Search Documents

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to +15oC. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO3 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi O2. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1958

By Vernon Taylor

CANADA'S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada's total. In the British Empire, Canada's production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad's production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world's total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company's No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By F. C. Sturges

FOR some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are solved. Recently we have completed two 36-in. diam. core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years [ ] and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam. shafts were considered, but actual computations showed 36-in. diam. shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1947

By A. D. Brokaw

The so-called "paraffin dirt" of the Gulf Coast oil fields has been considered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist. If the material is brought into suspension in water, very fine sand settles out and may be recovered by successive washing and decantation. The sand is almost entirely quartz, but contains occasional fragments of feldspar—more or less kaolinized and iron-stained. Practically all of the sand passes through a 100-mesh screen and the grains are extremely sharp —possibly below the limit of rounding. A flocculent mud, of clay and organic matter, remains in suspension for days. Some material is taken into solution in the water, imparting a slight tendency to froth when vigorously shaken. The results of partial analyses of four samples of "paraffin dirt," and, for comparison, one of a coastal plain soil are given in Table I.

Jan 1, 1920

By David B. Scott

The Mogollon mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent. of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. Location and Topography The town of Mogollon is 75 mi. (121 km.) by a poorly located highway ,. from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western slope of the Mogollon Range. The main canyons i run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the mines are generally dry. The mountain ridges between the canyons have altitudes varying from 7000 to 10,000 ft. (2130 to 3050 m.) and drop sharply, on their western face, to the floor of the San Francisco Valley at an elevation of 5000 ft. (1525 m.). Erosion has been rapid, and the

Jan 1, 1920

Discussion of the paper of EZEQUIEL ORDOÑEZ, presented at the Pittsburgh meeting, October, 19.14, and printed in Bulletin No. 94, October, 1914, pp. 2531 to 2536. DAVID T. DAY, Washington, D. C.-Dr. Ordoñez is really the pioneer in the study of the occurrence of Mexican oil. His studies came at such an early time as to prove really prophetic. He was successful in pointing out the relationship of these oil deposits to the volcanic teeth which are so very characteristic as a geological feature in the coastal plain of Mexico. At that time only the first wells around Ebano had been drilled, and drilled under the direction of Dr. Ordoñez himself. Only these Ebano wells were available for a real study of the condition of the occurrence of oil, the other large gushers not then being known. From that time on, the study of the geology of the country has, in large measure, been able to keep up with the oil development. As usual, a great deal of haphazard work in the exploration of the oil fields has been carried on. The results have been good, bad, and indifferent. We know a great deal more about the distribution of oil in Mexico than we do about the geology of it. Two ideas have become prevalent in regard to the Mexican oil, due to the peculiar development there: (1) That oil is omnipresent over a tremendous area bounded by De Soto La Marina, in the province of Tamaulipas, on the north, to south of Tuxpam in Veracruz; and (2) that there are very few spots in all this region which have rich gushers. The truth is somewhere between the two. The amount of land taken up, chiefly by three or four large companies, is extremely great, and covers all the possible chances. The idea that oil is going to be discovered in a large percentage of the land taken up by the oil companies, seems to me entirely unjustified. The amount of oil that will be produced from comparatively small spots here and there over that territory and other territory, undoubtedly will be very great. I do not think there is any hope of multiplying the capacity of these large gushers by the area of that part of Mexico in which they are contained, as a, large number of promoters are inclined to do.

Jan 4, 1915

By B. H. Lehnhard, C. J. Cecil

The paper describes the use of the Electric Pilot in the Permian Basin for making permeability surveys of wells and for the selective acidization of wells. A general summary of the information obtained from the many permeability surveys run in this area is given, and the possible application of this information to reservoir control problems is discussed. The application of the Electric Pilot on specific wells, involving well completion, acidizing and workover operations is also included. Introduction The Electric pilot is a comparatively new tool in oil-producing areas. From the beginning, the possibilities of this new service caught the imagination of many of the oil operators and acidizing engineers. Through the continued and ever increasing use of the pilot during the past year, and the close cooperation of the oil operators who have used this service, the efficiency and utility of the Electric Pilot service has been increased to a point where it is now a well established and recognized service. There are two major uses for the Electric Pilot: (I) permeability survey; (2) selective acid treatments. Permeability surveys are made to determine the thickness of the various permeable sections at the borehole, the vertical position of these zones at the bore hole, and the relative capacities of the various zones. Nomenclature Data obtained from the permeability survey are used to calculate three different indexes that pertain to the volume of fluid injected into the various permeable zones. A nomenclature for these various indexes has been set up, which correspond with the various productivity indexes, except that they are a measure of injected fluid rather than produced fluid. The nomenclature and definition of the indexes used in connection with a permeability survey by the Electric Pilot are as follows: 1. Capacity.—The volume of water injected into an individual permeable zone, in gallons Per minute. 2. Capacity Index.—The volume of water injected into an individual permeable Zone, in gallons Per minute Per pound Per Square inch differential Pressure. 3. Specific Capacity Index.—The volume of water injected into an individual permable zone in gallons Per minute Per pound per square inch differential per foot of thickness of the zone at the borehole. Capacity is the most generally used index, and for planning initial acidizing procedures and most workover jobs it is sufficient. For comparing permeability surveys on the same well before and after

Jan 1, 1945

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400' to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report' with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By John Dasher, Wilfred L. Freyberger, James H. Pannell, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By Earl Oliver

This paper is based on the formula that the petroleum industry is sick—find the cause, eliminate it, and the industry will get well. There is perhaps no difference of opinion that the cause is overproduction, actual or potential. But that, again, is a result rather than a cause. The problem is to study the influences that serve to keep production and consumption out of balance. Production control is a popular theme and a natural one at this time when the whole world is unstable; but production control in its popular sense means little more than the application of emergency measures while danger threatens. Economists differ as to the effectiveness of these, most of which are designed to alleviate and not to cure, but we assume there are none who question the wisdom of promoting conditions under which economic forces are permitted to operate freely in bringing about stable conditions. The petroleum industry suffers from two classes of economic ills that serve to promote overproduction; namely, those which are common to all industries and those which are peculiar to this industry. It is of the latter I wish to speak. Strange to say, government is responsible in large part for this latter class of ills that affect the petroleum industry and we are coming to recognize that only through the assistance of government can they be corrected. Instability of the petroleunl industry, in so far as human agency was involved, had its inception in 1875 when a Pennsylvania jurist, called upon to make a decision for which there was no precedent and fancying he noted some resemblance between the so-called fugitive nature of oil and gas and that of wild game, made mention of that resemblance. Other courts being impressed by the analogy enlarged upon it, and gradually fixed upon oil and gas a legal status in certain important respects similar to that of wild game. Although later the courts abandoned this analogy, certain practices that developed out of that early concept have continued to this day and are largely responsible for the industry's present plight. Thus, instead of ownership in place that is characteristic of private property generally, the law of capture was applied to oil and gas. Now, the rapid and wasteful depletion of game

Jan 1, 1932

By Arthur Notman

DURING the past fifteen years there has been a great change in the methods of treating employ-ment and discharge throughout industry. Perhaps nowhere has this change come more abruptly than in the metal mining districts of the West. In 1909, when I went to work for the Phelps Dodge Corporation in Bisbee, their operations were roughly arranged accord-ing to shafts in seven divisions, each employing from 100 to 250 men underground, and the mechanical department employing some 250 men, mostly on the surface. The underground divisions were each in charge of a foreman who had under him a night foreman and from two to four shift bosses on' each of two shifts. These foremen reported to the underground superinten-dent and he in turn to the superintendent of the mine department. The mechanical department was in charge of the master mechanic who reported to the superintendent of the mine department. RUSTLING A JOB IN THE OLD DAYS It was customary for men seeking employment to "rustle" the division foreman at the shaft during the lunch hour or at the close of the day shift and the master mechanic at the shops. There was no real attempt at interviewing the applicants for underground work. They simply filed in and out of the foremen's office-50 to 150 strong-in ten or fifteen minutes. If the foreman needed men, and he generally did; to replace those that he and the shift bosses had removed during the morning, he picked out those he knew or strangers who took his' fancy. The former in many cases were chosen for negative reasons rather than positive. In selecting the latter, the foreman felt that if they failed to show ability promptly, he could replace them the next day, and often did so. Even if these foremen had been skilful and well trained in the art of selecting men, it would have been impossible under the pressure of other duties to exercise that skill and experience in so doing. The conditions in the mechani-cal department were little better. About all that can be said in favor of such a method was that with a sur-plus of labor it "got by." The labor shortage brought about by the war disclosed its fundamental weakness.

Jan 6, 1923

By Douglas Bunting

The first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel. Although, as far as we know, the accidents of the past have not resulted in the loss of life, except in two instances, yet nearly all were attended with more or less miraculous escapes of men working in the vicinity of the breaks, so that the probable existence of pot holes, etc.,

Jan 1, 1915

By A. L. Holley

THE general usage of engineers, manufacturers, and merchants, is gradually, but surely, fixing the answer to this question. In every country rails, boiler-plates, and machinery bars, whether hard or soft, are almost universally called steel, when they are made from cast ingots. Other names for the softer steels, such as " homogeneous metal," " Bessemer iron," " Martin iron," and the like, have failed to obtain general recognition. The meaning of the term steel, before it was enlarged to cover newly developing varieties, has been traced, by a recent writer, down through Percy, Shakspeare, and the Bible, in a most interesting manner, from an archaeological point of view. Undoubtedly, it did characterize hardness and other qualities imparted by carbon. It is within the memory of most of us, that all steels were tool steels, and that the soft, structural varieties were introduced-varieties which harden but little, which bend cold, and which, in many physical properties, are akin rather to wrought-iron than to tool-steel. But, since both the hard and the soft steels are made by the same processes, and have their great, distinguishing structural feature in common, viz., homogeneity resulting from fluidity, it has come to pass, despite every other proposed nomenclature, that all the compounds of iron which have been cast in malleable masses, are called steel, the term wrought-iron being still confined to malleable iron made from pasty masses, and hence laminated in structure. No inconvenience has been found, so far, in distinguishing between the more or less carburized products, in general, by the terms " high-steel," " low-steel," " tool-steel," etc., and, in particular, by prefixing the percentage of carbon and other ingredients, to the terra steel. Steels which contain distinguishing ingredients other than carbon, are called "chrome-steel," " titanium-steel," and the like, just as variously compounded bronzes are called "phosphor bronze," "alu¬minium bronze," etc. Thus the combination of several words or symbols, and figures, may completely disclose the characters of the metal, in terms that are subject to no misunderstanding. But inasmuch as several high metallurgical authorities and clever writers have of late proposed to disturb this natural and somewhat settled nomenclature, it seems important to consider the claims of the various classifications. I shall attempt, in this paper, to show

Jan 1, 1876

By T. Cameron Kenney

INTRODUCTION Whereas the design of rock slopes in open-pit mines is done largely by mining engineers and geologists, the design of slopes in overburden at this point in time is a problem for which civil engineers or geotechnical engineers are best prepared to deal. The reasons for this situation are to be found in the educational curricula and the technical journals of the two groups, where soil mechanics has received little attention by mining engineers and geologists, and rock mechanics has similarly received little attention by civil engineers. In ten years' time this paper will hopefully be considered by young mining engineers to be a repeat of the material that they studied at university. However, even in ten years time I believe that the civil (or geotechnical) engineers will be extensively used as consultants on overburden- slope problems of open pit mines because mining companies will find this more expedient than maintaining their own geotechnical staff, special field equipment and special testing laboratories. For this reason, the purpose of this paper is not to condense several university soil mechanics courses into a twenty-page text for mining engineers and geologists. Rather, the purpose of the paper is to offer a general explanation of various factors affecting slope stability so that mining engineers and geologists will have a better understanding of the behaviour of overburden soils in slopes. A great deal has been written in soil mechanics literature on the subject of slope stability. No attempt will be made to reference all this material but rather only a selected number of references will be cited. Excellent general treatments of the subject of stability of overburden slopes are available (1,2,3,4). Further information of a more specialized nature is to be found in such publications as the Journal of the Soil Mechanics and Foundation Division of the American Society of Civil Engineers, Geotechnique (printed by the Institution of Civil Engineers, England), Canadian Geotechnical Journal, and the proceedings of the conferences of the International Society for Soil Mechanics and Foundation Engineering. FACTORS INFLUENCING SLOPE STABILITY There are two general scales of slope-stability problems, gross stability and local stability. Gross stability refers to large volumes of soil, and gross instability would involve large rotational-type shear failures. Local stability refers to something much smaller and examples

Jan 1, 1972

By B. B. Rath, Hsun Hu, R. S. Cline

FOLLOWING the techniques used by Beck and co-worker~ "~ the characteristics of selective growth in the recrystallization of a zone-refined aluminum single crystal, rolled 80 pct at -78°C in the (110)[112] orientation, have been studied. The material was 99.999+ pct pure. The as-grown crystal had a resistance ratio, R(298°K) /R(4,2°K), of approximately 5000. The method of preparation of the single crystals and the necessary precautions in handling them during rolling in order to avoid recrystallization in locally distorted regions were described in an earlier paper.3 The rolling texture of this zone-refined aluminum crystal is practically identical with that of less pure aluminum crystals rolle! in the same orientation, i.e., a very sharp (110)[112]. Random nuclei were provided by artificial nuclea-tion by abrading one face of the rolled crystal on 600-grit emery paper in a random fashion. The thin layer of disturbed metal recrystallized at room temperature into fine grains almost immediately. An X-ray diffraction pattern was taken from the abraded surface of the crystal, and the relative intensities of the various reflection peaks were compared with those obtained from a powder specimen. As shown in Fig. 1, the relative intensities of the various peaks from the recrystallized layer varied somewhat from experiment to experiment, depending presumably on the abrading technique. However, the texture of the recrystallized layer produced by this method is nearly as random as that of a powder specimen. Fig. 2 shows the texture determined from the "growth side" (face opposite the abraded surface) of the crystal after it was kept at room temperature for 100 hr. The specimen was only partially recrystallized, as shown by the remaining deformation texture. The new orientations are derived from the recrystallized grains grown through the thickness of the crystal from the "nucleation side" (the abraded surface). Fig. 3 shows the texture after complete recrystallization produced by annealing at 60°C for 1 hr. The arrows indicate 40-deg rotation around the (111) axes of the deformation texture. The microstructure of a completely recrystallized specimen is shown in Fig. 4. As shown in Figs. 2 and 3, the texture of the re-crystallized grains grown from the nucleation side to the growth side is essentially the same as that observed in less pure aluminum' (99.994 pct) and dilute alloyz crystals rolled in the same orientation. How-

Jan 1, 1968

By Henry Louis

The work performed by the Royal Commission on Mining Subsidence is likely to prove of permancnt value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions." Report on the Doncaster Area The Commission submitted an interim report at the end of 1925, which referred solely to one area, usually spoken of as the Doncaster area, and recommended that a Commission of a more technical character be appointed to investigate this particular case. This recommendation was acted upon, and the Commission thus appointed reported early in 1928. Here it is necessary only to indicate the nature of the special problem that had to be solved, the proposed solution being mainly of local interest. The Doncaster area consists of about 330 sq. miles of low-lying land in the southeasterly portion of Yorkshire and adjoining parts of Lincolnshire and Nottinghamshire. No less than 78 per cent, of this land lies below the 25-ft. contour line, and a good deal is even below high-water level. It includes a large tract of land known as Hatfield Chase, swampy ground which has always been a source of trouble on that account, so much so that in 1626 a Dutchman, Cornelius Vermuyden, was called in by King Charles I to devise and execute schemes of drainage for its reclamation. The entire Doncaster area is

Jan 1, 1930

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970