Search Documents

By J. N. Butler, R. J. Morris

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:1 are possible on head assays of 0.10 to 0.50 pct U 3 O 8. Additions of certain base metal salts aid in recovery and materially increase the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals. RAPID increase in mining and milling uranium ores during the past seven years and the discovery of large tonnages of uranium-bearing material too low in grade to stand the cost of leaching have developed considerable interest in possible methods for beneficiating these marginal ores. Such ores are generally classed as those containing less than 0.10 pct U3O8. Development of a beneficiation method that would give both high recovery and high ratio of concentration would also make possible the beneficiation of higher grade ores and would provide higher grades of feed to existing leaching plants. Although considerable research and testing on physical or physico-chemical beneficiation of domestic uranium ores has been done in the past, to the best knowledge of the authors only a single application of physical beneficiation is now in operation on a commercial scale. Flotation has been attempted on the basis of mineral association rather than by direct concentration of the contained uranium minerals. Flotation studies conducted on this project on certain ores gave recoveries of 60 to 70 pct of the uranium by the use of conventional flotation agents such as oleic acid, but ratios of concentration were in the order of 1.5:1 to 2.5:1. Subsequent cleaning to upgrade the concentrates rapidly increased losses in the cleaner tailings, which were not later refloated in the rougher flotation. Selection of Collector: In selecting desirable organic collectors for these oxide systems, a thorough study was made of the relationship between structural characteristics and collector activity by an examination of the behavior of a number of different functional arrangements present in a variety of organic molecules, (see Fig. 1). It is generally accepted that a collector must have a relatively long-chain hydrocarbon radical and a chemically reactive elec-trophilic center. Such a requirement could be met by a large number of compounds, but steric effects at the uranium mineral surface, solubility, compat-ability with aqueous systems, air avidity, bond strength at the mineral surface, interfacial concentration of the collector, and diffusion rate of the formed complex from the air-water interface eliminated many as unsuitable for this purpose. Preliminary investigations were completed of possible collector designs consisting of aliphatic and aromatic hydrocarbon radicals attached to stable combinations of nitrogen, oxygen, sulfur, and halogen electrophilic centers, Fig. 1.Tests were made to determine melting point spans, solubility of mineral-collector combinations in various solvents, reactions with soluble uranium salts, contact angles, and floatability by semi-quantitative beaker methods.' Contact angle determinations were not too useful because of the fine particle sizes of available mineral samples. From the foregoing study it appeared that nitrogen-sulfur electrophilic centers coupled with straight-chain saturated alkyl hydrocarbon radicals would hold the most promise for floating secondary uranium minerals. As the dithiocarbamate compounds can be made to combine these attributes they were selected for further study. The dithiocarbamates form a parallel structure to the xanthates, with the fortuitous exchange of

Jan 1, 1957

By J. S. Levine, M. Prats

Several methods are available for calculating the performance of solution-gas-drive reservoirs from the PVT properties of the oil and from the relative permeability and other properties of the formation. These methods require a number of simplifying assumptions. The present method of computation has made use of a high-speed computer to solve simultaneously the nonlinear partial differential equations that describe two-phase flow by solution-gas drive in order to calculate the performance of a reservoir. Some of the results obtained by the nonlinear partial differential equation solution are compared with those obtained with an approximate method, which has been called the semisteady-state solution. The pressure and saturation profiles from the wellbore to outer boundary calculated by the two methods are compared for one constant-terminal-rate case and two constant-teminal-pressure cases. The agreement in these profiles, as well as in the values of average reservoir pressure and cumulative recovery, leads to the conclusion that, for most engineering calculations, the semisteady-state method will give a reasonable approximation to the numerical solution of the differential equations describing solution-gas drive. An unfavorable (as regards ultimate oil production) set of relative permeability curves was used in the calculations in the belief that the effect of the parameters which were studied would be emphasized to a greater degree. Furthermore, the reservoir was assumed to be completely homogeneous, and these results should not be considered applicable to any other type of reservoir. Gravity effects are not considered. The absolute permeability was varied from 25 to 0.5 md. At an economic limit of 2 B/D, the recovery for a 25-md reservoir is about 1.8 times as great as that for a 0.5-md reservoir. The effect of permeability on the producing gas-oil ratio is minor. Once PVT properties of the oil and the relative penneability properties of the reservoir are fixed, the pro- during gas-oil ratio is found to be a function of the fraction of oil recovered. Well spacings of 10, 40 and 80 acres were considered. For the assumed homogeneous-reservoir properties, the effect of spacing on recovery at an economic limit of 2 B/D was very slight. Certain dimensionless groups can be used to extend the results to other fields having different penneabilities, spacings, reservoir thicknesses, well radii and porosities, so long as the PVT and relative permeability properties are similar to those used in this paper. INTRODUCTION An important aspect of reservoir engineering is the prediction of the performance of the reservoir based on the limited information normally available early in the life of a field. Usually, soon after a field has been discovered, it is necessary to decide upon the spacing to be employed and the production program to be used for most efficient utilization of reservoir energy. Where these decisions have not been dictated by legal or political considerations, they have frequently been based on experience factors which indicate that two fields with similar characteristics will probably have similar performances. To the extent that the industry has been successful in economically exploiting oil reservoirs, this rule-of-thumb method has been found to have merit. A large amount of theory has been developed with which it is possible to predict the performance of a reservoir by using certain known properties of the oil and the formation. Because of the difficulties of the mathematics involved for a drainage area having square or rectangular boundaries, the problem usually has been simplified and idealized by assuming each drainage area to have radial symmetry and the field to be represented by a number of these drainage areas. Muskatl was one of the first to formulate the theory for two-phase flow and to solve the equations for a few cases by numerical integration, using the relatively slow means of computing available at that time. His equations describing

By A. D. Schwope, L. R. Jackson, K. F. Smith

Burghoff and Blank1 have pointed out that the creep properties of hard-drawn coppers are closely associated with their individual softening characteristics and have further shown that the creep resistance of various types of copper is improved, under certain circumstances, by cold stretching. In the design of certain types of electrical machinery, it is important to have the creep resistance as high as possible; furthermore, short-time creep strength is important since in many cases stresses are large only during warming-up and cooling-down periods. In this paper, data are presented showing the effect of cold work on the short time creep strengths of various types of commercial copper under several conditions. It is shown that trends from short-time creep tests are evident at longer times. Materials Used in the Investigation The coppers used in this investigation were commercial grade and of two basic types, oxygen free high conductivity (OFHC) and tough pitch. Additions of silver in amounts of 15 and 25 oz per ton were added to each of the two coppers. The analyses of these six coppers are given in Table 1. Originally, they started as wire bars 4 X 4 X 54 in. A. square rod was made by hot rolling the wire bars to 9/16-in. rod in 8 passes. This rod was then cold drawn to 0.445-in.-diam rod and annealed for 3 1/2 hr at 1000°F. It was then cold drawn to 0.325-in. rod and again annealed at 1000°F for 3 1/2 hr. Hard square rods were then made by cold rolling to 0.257 X 0.257-in. rod. Soft wire was made from the hard- drawn material by annealing at 650°F for 3 hr. The final rolling was performed using a set of 9-in. grooved rolls revolving at 30 rpm, which produced square wires. Reductions of approximately 5, 20, 30, and 40 pct were obtained using several passes in the same direction for the large reductions. The 5 pct reduction by drawing was accomplished using a steel die having 2 parallel bearing surfaces. The die angle was 7 1/2 degrees and the wires were lubricated with a paste of ceresin wax dissolved in carbon tetrachloride. The speed of drawing was 13 fpm. Since work was done on only two sides of the wire simultaneously, it was necessary to rotate it 90 degrees each pass to insure uniform deformation. The room-temperature tensile properties of the various tempers are given in Table 2. The grain size of the an- nealed 0.257-in. wires was uniform and averaged about 0.035-0.045 mm. Experimental Procedures for Short-time Creep Tests Standard creep-test frames (Fig 1) were used for the testing. Special fixtures were designed to apply axial compressive and tensile loads to the copper wires. The compression specimens were 1 in. long and the ends were ground flat and parallel. The creep in compression was indicated by the movement of reference marks s-ratched on intersliding platinum strips attached to the moving heads of the fixture. The movement was measured with an optical micrometer fitted with a filar eyepiece on which the smallest division was 0.00005 in. The tensile creep specirriens were 4 in. long which provided ample gripping surface for the jaw-type grips. The platinum strips were attached to a one-inch gauge length of the wire and the creep measured as previously described. The single-specimen furnaces were connected to individual power and control sources. The controlling equipment consisted of Foxboro controllers

Jan 1, 1950

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,' and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson' determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12'13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-' have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.' Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967

By Rex W. Woods

The clue history of performance of a highly volatile type oil reservoir which is now greater than 80 per cent depleted is presented. The reservoir is at a depth of approximately 8,200 ft and includes an area greater than 7,500 acres. The reservoir has been exploited by 10 wells which to date have yielded about 10,880,000 bbl of stock tank oil by pressure depletion. Reservoir pressure has declined from an original of 5,000 psi to approximately 1,450 psi. Produced gas/oil ratio has increased from 3,200 to 23,000 cu ft/bbl with a corresponriing increase in APl gravity of the stock tank oil from 440 to 620 . Pressure and fluid data are given for different stages of depletion. INTRODUCTION In papers by Sloan,' and Cook, Spencer and Bo-browski,' properties of highly volatile type reservoir oil were discussed in detail and methods were presented for predicting performance of reservoirs containing this type of fluid. The purpose of this paper is to present performance history of a highly volatile type oil reservoir designated as Reservoir A which has been produced by pressure depletion and field separation without processing of gas GEOLOGY The reterence field which includes Reservoir A is a structural feature north of a trend of major folding along a northeast-southwest axis. In the area of development, the structure has the appearance of a dome with formation dip of three to four degrees, but structural relations between the reference field and the axis of major folding to the south have not been determined. No faulting within the field is evident. Oil and gas productive sands have been found at depths of 7,000 ft to 10,000 ft in a columnar section of Mio-Oligocene age. The sand bodies in the section are lenticular and usually continuity of sand is limited to a small area. Sand A which forms Reservoir A at a depth of 8,200 ft, however, has exceptional continuous development in the reference field. Fig. 1 shows an isopachous map of net oil sand for Reservoir A. Net thickness of oil sand at producing wells ranges from 14 to 34 ft with an average of 22 ft. Pinch-out of sand has been shown by drilling in the southwest part of the field, but extent of the reservoir on the northwest and northeast parts of the field is indicated only by thinning of the sand. The vertical oil column between the highest and lowest producing well in the reservoir is 339 ft. No water-oil contact has been found within the reservoir. As interpreted from the isopachous map, the reservoir includes about 8,900 acres with an average net sand thickness of 12 ft. Because of limited data on extent of the reservoir, the isopachous map permits only an approximation of sand volume in the reservoir. DEVELOPMENT AND PRODUCTION Reservoir A was discovered during 1938 and was developed with eight wells to the end of 1942. One well was completed during 1946 and the tenth well in the reservoir was completed during 1951. Three of the original wells and the last completion have produced from Sand A only. Six wells have produced from Sand A through the casing side of dual completions. Initial producing rates of the original wells ranged from 800 to 1,000 BOPD. Production history for the reservoir is shown in Fig. 2. Production of the reservoir was begun during 1940 and in May, 1952, peak production from seven wells was 5,300 BOPD. At the end of March, 1954. cumulative production was 10.880,000

Jan 1, 1956

By R. E. Reed-Hill, W. H. Hartt, W. A. Slippy

An unusual form of double kinking has been observed at the ends of {1121} twins in deformed zirconium. These kinks lie partly outside of the twin and partly inside. While they are undoubtedly closely associated with accommodating the twinning shear into the matrix, they are apparently closely related to other important aspects of twin growth. A mechanism is proposed for {1121} twin growth involving interactions between 1/3 (1120) dislocations in the bend planes and twinning dislocations. It is also shown that boundaries without long range strain fields develop at the tapered ends of the twins. The {1121} twins can, therefore, grow without forming high-energy noncoherent twin boundaries containing large numbers of closely spaced twinning dislocations. NUMEROUS investigators have indicated that slip is often closely associated with deformation twinning. An example is twin accommodation kinking,1-3 where dislocations form bend planes and permit accommodation of a twinning shear within the parent crystal. Another is the incorporation of slip dislocations into twins, as proposed by Sleeswyk and verbraak4 and Ishii and Kiho5 for iron and ß-tin, respectively, and observed in hcp metals by Price.6 In addition, it has been shown that shear discontinuities exist at the points of twin intersections in zinc,7 magnesium,8 titanium,9 ß-tin,10 and bismuth," where the continuity conditions for twin intersections, originally proposed by cahn,12 are not satisfied. A similar situation occurs for zig-zag (1121) twins in zirconium13 and ?-phase silver-aluminum alloys,14 where the twinning shears of the two component twins are not parallel. In all these latter cases additional deformation by slip is believed to accommodate the twinning shear discontinuity. The present paper is concerned with a newly observed aspect of the slip and twinning interrelation, in which two kinks, one inside the twin and the other external to the twin, are formed. These kinks, observed in conjunction with (1121) twinning in zirconium, form to accommodate the twinning shear. A model has been constructed explaining the growth and accommodation of (1121) twins in terms of these kinks. This mechanism may be significant since it is concerned with an important twin mode, which occurs not only in zirconium but also in titanium and hafnium. The practical significance of (1121) twinning has been adequately demonstrated. At 77° K the high ductility of zirconium containing a large number of grains unfavorably oriented for slip is primarily due to (1121) twinning.'5 Also, (1121) twins nucleated at 77°K may grow during further deformation at room temperature. This growth can greatly increase the transverse ductility15 as well as produce large mechanical hysteresis effects.= EXPERIMENTAL PROCEDURE Arc-melted, sponge zirconium plate previously described17 was prestrained 0.65 pct at 77° K by cold-rolling to introduce {1121} twins into the structure. Tensile specimens were cut with axes normal to the plate rolling direction. These specimens were pulled in tension to near the point of failure in an Instron machine at room temperature at a cross-head speed of 2 x10-2 in. per min. This additional deformation caused growth of the twins nucleated by prestrain. Deformed specimens were then prepared for metallo-graphic examination. This included an anodizing treatment18 that made the surfaces sensitive to polarized light, permitting small lattice rotations to be revealed. EXPERIMENTAL RESULTS Nature of the Twin-Kink Band Structure. Fig. 1 is a photomicrograph of a typical specimen after prestrain at 77° K. The structure is characterized primarily by long, narrow, parallel sided (1121) twins which norma1ly traverse the entire grain. Fig. 2 shows several (1121) twins after additional straining at room temperature. These lie near the center of the polarized light photomicrograph and are inclined upward to the right. It is evident that this latter deformation has resulted in appreciable twin growth. The dark regions extending from the ends of these twins are accommodation kinks. The difference in reflected light intensity indicates the

Jan 1, 1969

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li2O and 0.45 pct Fe2O3, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing. SINCE the close of World War II there have been numerous developments resulting in the increased use of lithium by industry. Notable among these has been the development of an industrial lubricant, based on lithium stearate, which is fluid at low temperatures, stable at high temperature, and insoluble in water. A new bleaching agent, lithium hypo-chlorite, has also been developed recently.' Other well-known uses are listed below: 1—Lithium oxide in ceramics reduces firing time, lowers melting temperatures, lowers thermal expansion, raises refractive index, and improves chemical resistivity. 2—Lithium carbonate and lithium strontium nitrate are used in pyrotechnics for their brilliant red color.' 3—Lithium chlorides and fluorides are used as fluxes for welding aluminum and magnesium.' 4—The affinity of lithium for nitrogen is the basis for a process used in purifying helium." 5— Lithium chlorides and bromides are used in air conditioning for their powers to absorb organic amines, ammonia, and smoke.6-—Lithium hydride has been used as a source of hydrogen to inflate life rafts and balloons used by the Air Forces and Navy.' 7— Lithium metal and lithium hydride are useful in the atomic energy program in connection with the production of the isotopes of hydrogen." During the 1942-45 period of World War 11, Solvay Process Co. operated a flotation plant with a daily capacity of 300 tons of ore for the production of spodumene concentrate near Kings Mountain, North Carolina. The operation was shut down upon reduction of wartime demand for lithium chemicals, and until recently there has been no production from the Carolinas. In April 1950 an investigation of the problem of spodumene flotation from North Carolina ores was begun at North Carolina State College Minerals Research Laboratory at Asheville, N. C. This laboratory, operating under the combined auspices of North Carolina State College, North Carolina Department of Conservation and Development, and the Tennessee Valley Authority, undertook the spodumene project at the request of Foote Mineral Co. of Philadelphia. The work, involving a period of 15 months of intensive batch and pilot plant investigation, was completed in June 1951 and resulted in development of a process for concentration of spodumene by flotation which has been hereto unrecorded in the literature. A similar approach has been used before on iron, ilmenite, and other minerals, but the literature shows no record of its having been applied to spodumene. Parts of the process are now being used on a commercial scale at the Foote Mineral Co. plant near Kings Mountain, N. C., which has been in production since July 1951. It is the purpose of this paper to describe some of the results of the investigation. The Orebodies Spodumene-bearing pegmatites occur in a narrow belt 24.5 miles long and 1.8 miles wide extending southwestward from Lincolnton to Grover, N. C. According to statements judged to be conservative, the tin-spodumene belt of the Carolinas contains an estimated 4,300,000 tons of pegmatite ore averaging 15 pct spodumene. This amounts to "a reserve of at least 650,000 tons of spodumene (more than 20,000 tons of metallic lithium) to a depth of 100 ft."' This figure includes only bodies having an average thickness of 35 ft and length of 550 ft. There are hundreds of pegmatites in the belt, many of which are less than 10 ft wide. The largest pegmatite in the area has a maximum thickness of 395 ft and maximum length of 3250 ft.' These larger pegmatites are composed principally

Jan 1, 1954

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By C. E. Williams, G. H. Bruce

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et&apos; al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4&apos;5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7&apos;8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

By J. E. Miller, W. E. DeVaney, L. Stroud

During a recent phase study of a natural gas, two stable equilibrium liquid phases were observed at temperatures below —200°F and pressures above 200 psi. This paper reviews the published literature on the occurrence of multiple equilibrium liquid phases and presents analytical data for the vapor and two equilibrium liquid phases of the liquefied natural gas at five experimental conditions. In addition, data for 30 conditions of two-phase equilibria are included. INTRODUCTION The low-temperature phase behavior of gases, most of which contained helium, has been investigated in the laboratories of the Helium Activity for many years. Since 1952, experimental studies of these systems have been continuous as part of the research program at Amarillo, Tex. Because of their value to private industries interested in participating in the Helium Conservation Program, several "Open File" reports containing phase equilibria data for heliurn-bearing natural gases have already been released by the Helium Activity. A paper containing information on the general phase behavior, operating criteria and extensive vapor-liquid data for two helium-containing systems was recently published.2 Additional publications presenting experimental data on the phase relationships of various gas systems are now in process and will be available in the near future. PREVIOUS EXPERIMENTAL WORK Although the formation of multiple liquids has been reported for various systems, to our knowledge this paper is the only substantiated evidence of a vapor-liquid-liquid equilibria in a naturally occurring gas. In 1940, Vink, Ames, and others13 reported the presence of two liquid phases in a hydrocarbon system consisting of mixtures of crude oils, solvents and natural gas. Eilerts and co-workers; published data on the recombined fluids from a gas-condensate well. This condensed gas, containing approximately 76 per cent methane and 24 per cent ethane-plus, exhibited two distinct liquid phases. Weinaug and Bradley 14 observed "unusual" phase behavior in a reservoir mixture. These workers postulated that the anomalous phase behavior was due to the "imminent formation of a second liquid phase". Botkin, Reamer, Sage and Lacey 1 studied two California crude oils that exhibited multiple phases. Kohn and Kuratal0 recently reported two equilibrium liquid phases in the methane-hydrogen sulfide system. Roof and Crawfordl1 and Eakin, et a16 also have reported experiments with binary systems that formed two stable equilibrium liquid phases. APPARATUS AND PROCEDURE A U. S. Bureau of Mines Phase Equilibrium Apparatus was used in conducting this study. The apparatus and procedures employed in its operation have been previously described3 and will not be repeated in detail ill this report. Briefly, the apparatus consists of a windowed cell which can be maintained within ±0.5°F for temperatures between room temperature arid -320°F. Pressure within the cell can be maintained within 0.1 per cent of gauge reading up to 800 psig. Equilibrium vapor and liquid samples are obtained in special containers4 for analysis by a mass spectrometer. Although the accuracy of the analyzer is about ±0.1 mol per cent, the reproducibility of the phase-equilibrium apparatus is considered relatively poor. Values reported from methane and nitrogen are considered accurate to ±l.0 and ±0.6 mol per cent. Data for ethane-plus in the vapor are accurate within 0.2 mol per cent; liquid-phase data for this aggregate compolnent are accurate within 1.5 mol per cent. For helium in the vapor phase, the analytical data are accurate within 0.2 mol per cent; liquid-phase analyses for this component were obtained by the charcoal adsorption method described by Frost8 and are accurate within 0.006 mol per cent. All of these references to the accuracy of reported values are conservative estimates based upon a statistical treatment of reproducibility data obtained with the apparatus.

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By Hisaaki Takata, Nobukazu Nanko, Ichiro Izawa

INTRODUCTION Tochibora Mine belonged to Kamioka Mines, which are located in Gifu Prefecture, the cen- tral part of the Japanese main island, has occupied the important position as a main source of silver, lead and zinc for the smelter of Mitsui Mining & Smelting Co., Ltd.. The annual production of crude ore goes up to about 1 mil- lion metric tons with average grades of 20g/t Ag. 0.31% Pb, and 4.18% Zn. For the last 20 years, the mine has struggled with the depressed zinc metal price in yen and the escalation of operating cost, especially la- bour cost. For instance, prices of commodities and labour cost have been raised 8 times and 14 times respectively during this period. On the other hand, total operating cost has been con- trolled to increase 4.5 times. The productivity of the mine has been increased 4 times by means of improvement of individual works and adoption of perfectly mechanized trackless mining system to reform the mining method. Some improvements are presented as follows; Today, drifting is carried out by the tunnelling crew which consists of 9 operators equipped with 5 Mobile-Jumbos, 2 LHD&apos;s and a jeep for carrying and loading ex- plosives. In order to get the high utilization of these machines, each crew manages systematically and continuously adjacent 15 faces under the direction of a forceman. As a result, we have accomplished high advance of drift. Furthermore, raising is carried out by a set of the raise-borer in case of long raises like ore- passes and also by the stage blasting method in case of short ones like slot-cuts. Generally speaking, the sublevel stoping method is considered to be one of the best methods for various respects; high productivity, low cost, easy grade control and safety. This method has been introduced in Tochibora Mine since 1950 and is now widely applied to lodes that could not be mined before by this method be- cause of the shapes of them and the conditions of their country rock. Now we are convinced to be nearly accomplished for our method. This report presents some examples of the standard sublevel stoping method and its variations which are practised at the mine. STANDARD SUBLEVEL STOPING Up to 1979 since 1950 when this method was first applied at the mine, 17 million tons of crude ore have been produced by this method, which amounted to 55% of the total production of the mine. During three decades, the productivity has been increased considerably by means of trackless mining system using large-sized machines and etc.. In other words, mining efficiency has been increased from 20 tons/man.shift to 100 tons/man.shift at large stopes. Formerly undercutting was carried out above the drawing drift by jack-legs and small scrapers and then several cone-shaped glory holes were made by stopers between the undercut level and the draw level. But now, a undercut drift is driven in parallel with the haulage drift at the same level of it. And at the undercut drift, drilling upward is carried out by a large-sized machines like the fan drill in order to extract the broken ore directly at the drawing drift connected with the haulage drift. Simplification of the work as well as utilization of large- sized machines enables to get higher productivity. But if the deposit is comparatively wider and the broken ore around the middle part of the deposit cannot be extracted, several drawing drifts are driven to the deposit and in order to minimize dead ore at the final stage of operation, the

Jan 1, 1981

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last 15 years. Fifteen years ago a 21/4-cu-yd front end loader was the largest standard machine you could purchase. Today there are two commercially available 15-yd front end loaders and many 10-yd loaders. The estimated total worldwide market for all front end loaders over 1 cu yd has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 and 24-cu-yd front end loaders in prototype form. It is not inconceivable that within another 15 years there will be front end loaders in the 50-cu-yd class with design features quite different from today&apos;s. These larger loaders are being designed at the demand of the mining industry, and the design criteria are being directed at this market area. The costs of these larger loaders may be greater per unit of capacity, but it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Table 1 are data for U.S. production of front end loaders (5 to 6-cu-yd class and 10-cu-yd class) and U.S. production of cable-operated, crawler-mounted power shovels, draglines, and cranes (11/z to 5-cu-yd class) for the years 1965 and 1970 (Source: Bureau of Census, U.S. Department of Commerce). Many believe that the decline in shovel production, in particular, is due at least in part to the acceptance of the front end loader as a primary production tool. However, the foregoing comparison is for a smaller shovel class than for front end loaders. It has generally been a rule of thumb that a front end loader is competitive on a cost and production basis with a shovel when it is approximately twice as large as the shovel. This same relationship may not hold true with the larger 10 to 15-cu-yd electric shovels, but at some point, direct competition will probably occur. Current Trends There are many trends today that are significant. One major usage trend in large front end loaders involves load and carry operations. This application is defined as "performing the functions of loading, hauling and dumping with one machine over distances within its economical limits." Many people are using front end loaders to transport material as well as load it. It is estimated that nearly half of all 10-cu-yd front end loaders sold in 1970 went into primary load and carry work. Many times, significant savings result from using the load and carry system, instead of small truck and shovel operations, for distances in excess of 1000 ft. Strip mining in coal utilizes great numbers of front end loaders in this manner. In-pit crushing of limestone is developing on an ever-increasing level, especially in Europe, and this stimulates interest in load and carry operations. In Table 2 is a cost example for 10-cu-yd front end loader in a limestone quarry. More than likely, load and carry use will continue to increase over the next few years. While some types of mining do not lend themselves to load and carry in the pit, such areas as surge piles are applicable and should be studied. In the area of machine operating cost reduction, there

Jan 1, 1974

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer&apos;s organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By H. M. Myers, J. E. Funk

The two-phase flow of a drilling fluid in a diamond drill bit is investigated by deriving and solving the steady-state continuity and momentum equations. Parameters in this analysis are rotational speed of the bit, local rate of addition of drill solids, non-Newtonian nature of the drilling fluid and drilling rate. The describing equations relate the flow and pressure drop to the design characteristics of the bit. The equations are integrated numerically yielding the flow-rate pressure drop characteristics for the bit, flow distribution in the bit and velocity and static pressure as a function of position in each flow channel of the bit. Results are presented for a particular bit design. This paper shows that under normal drilling conditions certain parameters may be neglected in the hydraulic calculations for a diamond drill bit. Therefore, shortened forms of the equations presented can be used to fit the proper diamond bit to the drilling fluid hydraulic system. INTRODUCTION Like the conventional bit, the diamond drill bit is a key component in the circulating system of a well. The conventional rock bit is fitted to the circulating system by selecting the flow nozzles which provide the system with the proper flow-rate pressure drop relationship. Fluid behavior across the face of the diamond bit must be better understood so the bit can also be fitted to the circulating system. Data from field-operated diamond bits are presently available and do yield some information regarding the flow-rate pressure drop relationship. However, the number of factors affecting this relationship is quite large. Drilling parameters and conditions such as bit penetration rate, bit weight and rotational speed are important. Moreover, flow channels in the bit are part of the cutting head, and introducing drilled solids into the flow channels reduces the flow area, causes additional drag and influences the pressure drop. Many tests would have to be performed if field tests were required to study all parameters which might influence fluid behavior in the bit. A logical approach to this problem is to investigate analytically the fluid behavior in the bit, including parameters that are present under normal drilling operations. This approach, which seems to offer the best method for future studies, is presented in this paper. Following is the general procedure. 1. Equations describing the most general flow channel are written and include the addition of drilling solids (which is related to penetration rate), rotation of the bit, design parameters of the bit and non-Newtonian properties of the fluid. 2. A typical bit is designed and the bit parameters are substituted into the equations. 3. Parameters are assumed (penetration rate, rotational speed of the bit, mud weight, etc.). 4. The describing equations are numerically integrated to obtain the pressure drop across the face of the bit as a function of flow rate. 5. The pressure-drop contribution of each component (friction, acceleration, etc.) is obtained from the numerical solution, and those factors which largely influence the total pressure drop are identified. Classifying the drilling fluid is important in establishing the friction factor relationship since the frictional pressure losses are the main contributors to the total pressure drop. High-density drilling fluid is commonly assumed to be a Bingham plastic. 1-3 Govier4 presented a method for selecting a friction factor in the laminar flow region from the rheology properties of the mud and a modified Reynolds number. Metzner5 presented a criterion for selecting the friction factor in the turbulent flow region. The bit design used in conjunction with the solution of the equations has divergent flow channels. Stall, which is the backflow of fluid in the channels due to eddies that occur on the outer perimeter of the flow stream, can occur in these divergent channels (or diffusers). When stall does occur the static

By R. S. Shoemaker, D. L. Harris

PST investigations into the possibility of concentrating the low-grade iron ores of the Gogebic Range in Wisconsin have been hampered by the complex association of the constituent minerals. In part the problem arises from the fact that the iron occurs essentially as two minerals, hematite and goethite, having nearly the same chemical composition but exhibiting different physical properties. Individual grains of these minerals are usually so small that the ore must be ground to a size finer than 325 mesh if substantial liberation of the minerals is to be secured. Appraisal of beneficiation tests on this iron ore requires, therefore, some method of determining quantitatively the contents of constituent minerals in the various products of the beneficiation. Because of the chemical similarity of the two iron minerals, chemical analyses do not provide a means of differentiation. Although the minerals are different physically, they are both opaque and friable, and as the ore must be ground to a very fine size for liberation to be secured, quantitative microscopic methods of analysis are extremely difficult at best. In an effort to overcome these analytical problems, a quantitative X-ray diffraction analysis method has been developed at the University of Wisconsin for the research program on iron ore beneficiation. The X-ray diffraction analysis of chemical compounds of crystalline form has proved of inestimable value for structure studies and rapid qualitative analytical purposes in a number of fields.&apos; In some cases X-ray diffraction analysis has been found suitable for quantitative determinations. H. P. Klug2 found that quantitative procedures for quartz powders when mixed with calcium fluoride were reproducible within ±1.0 pct. Talvenheimo and White3 reported quantitative analyses of clay minerals to be accurate within 10 pct and also detected 1 pct of bentonite in 99 pct illite. In other investigations,&apos;" powders of quartz and mica have been analyzed quantitatively with accuracies from 1 to 5 pct. A powder of tungsten carbide was analyzed similarly by Redmond7 and Rooksby8 reported the determination of small amounts (0.11 pct) of calcium oxide in magnesium oxide. In the most generally practiced use of X-ray diffraction, traces of the diffracted beam are recorded as lines on a film much as lines of elements are recorded on an optical spectrograph film. As with the spectrograph, the darkness of the lines denotes the amount of the constituent in the sample. If the film is replaced by a Geiger tube assembly and a graphic recorder or a scaling unit, the intensity of the diffracted beam can be registered as a peak on a chart or energy impulses per unit of time on the scaler. Several methods of quantitative measurement have been investigated and reported in literature. Klug2 used manual operation of the goniometer and a counting technique to determine the difference in counting rates at the diffracted angle and for the background. In another case3 the area under the recorded diffracted peak was the basis for the determination. In other instances the height of the recorded diffraction peak above background, measured while the goniometer was moving, has been the basis for the measurement. The sizes of particles most suitable for diffraction techniques are reported in the literature as follows: for tungsten carbide a maximum of 40 microns7 and for quartz a maximum of 5 microns.&apos; Very fine sizes of crystals are known to cause a broadening of the diffused beams; hence some workers have set a lower limit of 0.1 micron for quantitative results. Guinier10 has indicated that broadening of the diffracted X-ray beam is not appreciable for crystallites larger than 0.02 to 0.03

Jan 1, 1956