Search Documents

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Beecher

The application of gas or air under pressure to obtain more oil from a sand which has been practically exhausted by ordinary production methods has been practiced to a limited extent for many years. Until recently such methods were confined to the Eastern fields, principally those of Ohio and West Virginia, where in many cases the production obtained after applying pressure for a few years was nearly equal to the total production prior to that time which had been obtained by the usual production methods. As early as 1917, J. 0. LewisL called attention to this method of increasing the recovery of oil and cited the phenomenal results obtained by H. E. Smith, I. L. Dunn and 0. C. Dunn, who pioneered the application of air or gas pressure recovery methods. With this information available it would appear that other oil-producing sections of the country have been extremely slow to realize the advantages of repressuring. However, after a few successful projects in the Mid-Continent area, the oil producers appreciated t' e value of this method for obtaining further and profitable production from their practically exhausted leases and are now making extensive use of it. In general, it has been the practice to apply pressure to the sands when production has declined to a small yield per well. The purpose of this paper is to discuss some of the advantages which may be expected from returning gas under pressure to the oil sands during the early stages of development, before the rock pressure has been dissipated and the gas exhausted, and to stimulate discussion of this subject on which comparatively little actual field data are available. The Function of Gas Gas associated with or dissolved in the oil is the source of energy causing movement of the oil to the well. When this energy is dissipated production ceases. The exception to this general statement is found in fields where hydrostatic water pressure may supply energy after the gas

Jan 1, 1929

By Earl Oliver, J. B. Umpleby

It is believed that in connection with the study of unit operation by the Petroleum Division of the A. I. M. E. a review of the simple principles of unit operation would be helpful. To that end, the following discussion is submitted. It is not to be considered in any sense as the conclusion of the committee, but rather as material submitted for its consideration and represents at this time only the viewpoints of its authors. Growth of the Oil Industry In 70 years the oil industry has grown from a single well on Oil Creek, Venango County, Pennsylvania, producing 25 bbl, per day, to more than 400,000 wells scattered over five continents with a daily output of 4,000,000 bbl. In that time petroleum has expanded from its simple use as a medicine in a few localities to a multitude of diverse uses in homes of every country the world over. During those years the oil fields of the United States have produced two-thirds of the world's output and have shipped their excess production into almost every country. In those years several hundred thousand good wells in the United States declined into small ones and depleted shallow deposits gave way to deep zones; so that the United States crude oil industry gradually changed from one of low cost production to one of higher cost. Throughout its entire life it has labored under two serious economic disadvantages, namely, constantly recurring periods of demoralization through overproduction, and competitive development methods that are wasteful. Development of Foreign Competition During the transition from low to higher cost production in the United States, events even more significant were taking place in foreign lands. Jungles were tamed and deserts conquered. Oil deposits were found and developed until, in the words of Sir John Cadman, "the globe is now drenched with a commodity which, although necessary to life, involves but an irregular and sometimes meager expenditure of life in its

Jan 1, 1930

By A. W. Ambrose

The present plans for the Petroleum Division of the American Insti-tute of Mining and Metallurgical Engineers provide for two principal meetings in the year 1928. The first will be at Tulsa, Okla., in September or October, 1928, with the exact date largely dependent upon the date of the .International Petroleum Exposition. The officers wish to hold the meeting at the same time as the Exposition in order that members of the Petroleum Division of the A. I. M. E. may have the advantage of attending both meetings at the same time. It is planned that this meeting will be devoted largely to petroleum production engineering problems. A tentative outline of subjects to be discussed is as follows: 1. Repressuring New Oil Fields, and naturally in conjunction with this falls Repressuring of Old Fields. 2. Air or Gas Lift. 3. Flow Strings in New Wells. 4. Deep Drilling Technique. It is also planned to have at this meeting a general paper relating to Supply and Demand of Petroleum and its Products. The second meeting is planned for February, 1929, in New York at the same time as the annual meeting of the Institute. Special details have not been carried very far on this meeting, although it is expected the program will cover technical problems in relation to production and refining of crude oil, as well as 1928 development in foreign fields and the United States. It is planned during 1928 to cooperate with the Bureau of Mines in an attempt to compile a set of definitions on petroleum engineering. These would be of value to the petroleum engineering profession, in order to better standardize various terms used in discussion of current problems. It has also been suggested that the Petroleum Division study certain problems in which research work is needed by the petroleum industry and outline certain definite programs that could be carried out by the Bureau of Mines and the U. S. Geological Survey, as a follow-up to

Jan 1, 1928

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed' figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

By M. S. Azun

The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also. I do not agree with the conclusion implying that the main goal for state companies is to capitalize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondent government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 1, 1985

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By Paul R. Martin, R. B. Kelly

The area comprising what is geographically termed "Central Texas" was somewhat less active in 1934 than in 1933. The year saw the completion of 182 dry holes and only 74 producing wells. Bexar, Williamson and Bastrop counties, with active fields such as Yturri-Southton, Byersville, North Dale and Cedar Creek contributed a majority of the new oil wells. Hilbig, in Bastrop County, 1933's most important discovery in the district, saw no development during the current year. New fields opened in 1934 were Byersville, a serpentine intrusion in Williamson County, and Manda, producing from similar material in Travis County. Like most of the other serpentine plugs, neither gives promise of covering a very large area. Other active counties were Bexar, Bastrop and Caldwell, although successful operations in each of them were limited to the old fields. The location of producing fields is shown on Fig. 1. New Fields Byersvil1e.—Late in 1933, Fritz Fuchs completed Zeischang No. 1, eight miles south of Taylor, Williamson County, for an initial production of 25 bbl. per day. The oil is 37" B6. A.P.I. gravity and is from Serpentine formation at approximately 900 ft. Additional drilling was carried on in 1934, and at the end of the year 18 producing wells had been completed, proving about 200 acres. Manda.—The Manda field, or Kimbro field as it is termed by some, received its first production Sept. 10, 1934, when the Humble Oil & Refining Co. completed No. 1 C. J. Peterson as an 8-bbl. oil well. The new field is near Littig, in eastern Travis County, and is about 15 miles northeast of Austin. Production is found in serpentine formation between 650 and 750 ft. The same company's No. 1 Buck Christian, second well in the field, flowed 190 bbl. per day through a ?-in choke. Although only a small area has been definitely proven it is expected that present drilling will provide extensions in several directions.

Jan 1, 1935

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By Leo D. Jones

The use of the centrifuge for dewaxing lubricating oils grew out of the effort to secure better results than had been attained by the common "cold settling" process. This process was the only known method for dewaxing steam refined cylinder stock (600" F. fire test), the product known as "bright stock" being commonlyused for building up "pressed," i.e., dewaxed neutrals of, say, 200-sec. viscosity [to a higher value. The process consisted of mixing the cylinder stock with approximately one and one-half times its volume of naphtha, heating, to dissolve completely all the oil and wax and then slowly chilling to about 15" F. in large insulated tanks. This caused the wax to precipitate. It was allowed to settle out by gravity. The supernatant liquid was then drawn off and the naphtha distilled off, leaving a still residue of bright stock. The sediment from the settling, of a slushy nature, was withdrawn. After removing the naphtha by distillation the residue was petrolatum. At some point in the process, preferably after the dilution but before chilling, the mixture was decolored by percolation through fuller's earth. The finished bright stock produced by this process had a cold test of about 50" F. Efforts to improve this by chilling to a lower temperature resulted in a considerable reduction in yield, and increased uncertainty of settling. Even when chilling to 15" F. it was not uncommon to find that after a week's waiting a tank had not settled. It was then necessary to heat and rechill. This uncertainty was a serious problem; in one case a refinery superintendent had men riveters hold pneumatic hammers against the tank for hours, hoping thus to cause agglomeration and settling of the wax. Yields of bright stock above 70 per cent, were uncommon. History of Centrifugal Application It is not surprising, therefore, that many attempts were made to improve upon the results obtained by cold settling. George H. Taber, vice-president of the Gulf Refining Co., Pittsburgh, Pa., made a number

Jan 1, 1924

By James Gayley

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1906.) It is to be regretted that the data respecting the use of dry-air blast, which were presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. It appears from the reported discussion that some of those who took part felt themselves to be at a disadvantage, in considering the economies secured through the use of dry-air blast, by reason of the fact that the data presented covered so short a period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs; and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natu-ral air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jan 1, 1906

By C. A. Heberlein

The present war in Europe seems to have stimulated the demand for quicksilver. In July last, the price ranged around $35 per flask of 75 Ib., while to-day it seems to fluctuate between $47.50 and $50. The use of quicksilver in the form of fulminate, containing 70 per cent., and as corrosive sublimate, containing 73.8 per cent., must be extensive and a further market advance may be expected. With such an advance, some revival in quicksilver mining may be looked for, particularly in California, where many abandoned properties exist. What can be done with low-grade quicksilver ores under favorable conditions, particularly with low mining cost, may be seen from the following description of the Oceanic mine, near San Luis Obispo, Cal. Its operations date back to 1876, when rich sand ores were discovered. In three years 7,400 flasks of quicksilver were produced, but since then the deposit has been worked only sporadically . Until two years ago various attempts had been made by the Oceanic Quicksilver Co. to mine the more refractory "mud rock," which was encountered lying beyond the " sand rock." Mud and sand rock in varying quantities were treated together, with poor results, but operations were successful with sand rock of fair percentage. About two years ago, when all the sand rock had been exhausted, Murray Innes purchased the Oceanic mine. He found large quantities of low-grade mud rock, varying from 6 to 8 Ib. of quicksilver per ton, which at the prevailing low price of quicksilver demanded very cheap mining costs, in conjunction with high but cheap metallurgical extraction. At that time the extraction of quicksilver from mud rock ranged between 40 and 50 per cent., as far as I am able to learn. Mining The low cost of mining was the principal consideration, since, with mercury at 50c. per pound, the total gross value of the ore did not exceed

Jan 1, 1915

By M. C. Messner, L. P. Davidson

The Giesche Spas Akcyjna, in Polish Upper Silesia, produces zinc, lead and coal, together with many byproducts emanating from the zinc-lead ores. The development of the concern in the 230 years of its existence has been influenced not only by metallurgical improvements but also to an unusual extent by political and economic factors. The company was founded by George Giesche, who was born in 1653 and died in 1716, and who in 1704 received from Emperor Leopold I the exclusive privilege of mining and selling galmei1 in Silesia. His children, who retained the business, gave the name to the firm—George von Giesches Erben. After 1802 modifications in the Prussian mining and corporation laws limited the rights formerly enjoyed. The family concern became a corporation and expanded its activities, building smelters and opening new mines. The establishment of the present eastern boundary of Germany resulted in the transfer of nationality of a large part of the mines and surface plants to Poland, which, in turn, necessitated the formation of a Polish company, the Giesche Spólka Akcyjna. The first concentrators at the Bleischarley mine were built between 1854 and 1860 and owing to dual ownership were two in number. They were used only for the treatment of galena. In 1873 a concentrator was built for the treatment of sulfide ore preparatory to treatment in the Recke roasting plant, which was the first to have an acid plant for recovery of the sulfur gas. This concentrator was replaccd by a larger one in 1888, when the present orebody was opened up. At the same time, a mill was built for the treatment of the galmei. The concentration of the sulfide ore resulted in a much higher grade of feed for the zinc plants after the first troublesome steps of the roasting process had been worked out. Consequently, the oxide ore in its primitively concentrated state was no longer highly valued as a retort charge. and steps had to be taken to increase its zinc content.

Jan 1, 1935

By R. V. Norris

The removal of mine-water by hoisting in tanks instead of pumping, while somewhat a reversion to the methods of the ancients, has come very rapidly into favor in the anthracite region of Pennsylvania during the past few years. In fact, so much so, that at the present time there are at least eight large collieries at which all the water is hoisted, and six more plants are in preparation. The particulars of the plants in operation and under construction, as far as decided on, are given in the tables on pages 107 and 108. Besides these, the Delaware, Lackawanna and Western R.R. Co. is constructing a hoist of large capacity for a depth approximating 500 feet, to be located in the Keyser Valley, near Scranton. The hoists will be driven by electric motors, geared directly to the sheaves. The Lehigh Valley Coal Company is planning a large hoist for the Packer collieries in the Shenandoah district, but no work has been done on this as yet. The earliest regular hoisting, I believe, mas done by means of semi-cylindrical tanks (Fig. 1) at the Nanticoke collieries of the Susquehanna Coal Company. These tanks were attached under the regular shaft-carriages, taking in water through six large clack-valves in the bottom, and discharging through an endgate opened by a lever which was operated by a guide-piece on the shaft head-frame. These tanks were designed July, 1880, by the late J. H. Bowden, one of the very early members of the Institute. Similar tanks are still used in emergencies at the Nos. 1, 2, 3 and 6 shafts of the company. The objections to. their use were: that water could only be hoisted during the night-shift, or when the shafts were not in use for hoisting coal, thus requiring a very large sump, and greatly limiting the water capacity of the plants; that the alternate wetting and drying

Jan 1, 1904

By Fred C. Bond

SIX years have passed since the last grindability table was published.' In that time the list has been increased with many new tests, and the development of the new Third Theory of Comminution2 has made possible the reduction of all results to a consistent work index value. In this tabulation all grindability and crushability test results are given in terms of the work index, with formulas for reversion to the older units if desired. The average values for 57 different classes of materials are listed in Table I. The total number of work index values listed is 1211, and the overall average work index is 14.42. The complete tabulation, with each test listed alphabetically both under material type and under company name, can be obtained by writing to the Allis-Chalmers Manufacturing Co., Processing Machinery Department, Milwaukee 1, Wisconsin. The work index Wi is the calculated total work input in kilowatt-hours per short ton required to re- duce from theoretically infinite particle size to 80 pct passing 100 microns, or to approximately 67 pct passing 200 mesh. The work inputs required per ton for the same size reduction of different materials are directly proportional to their work indexes, and according to the Third Theory the work input per ton is inversely proportional to the square root of the diameter of the product particles. Where W represents the work input in kilowatt hours per ton, where F is the feed size, or diameter in microns of the square hole which 80 pct of the feed passes, P the product size, or microns which 80 pct of the product passes, and Rr the reduction ratio F/P, the work index Wi is found from Rr-l 100 When the work index Wi is known, the work input W required to reduce from any feed size F to any product size P is found from W = Wi ( Rr- 1 100

Jan 1, 1954

By Riki Kobayashi, Donald L. Katz

The dew point of natural gas which has been in equilibrium with gas hydrates has been reported to be lower than that obtained for natural gas in equilibrium with water1,? Hammerschmidt' reports a lowering of the dew point of 13 F for a natural gas in equilibrium with hydrate at 380 F and 525 psi. Records and Seely2 likewise show that the dew point of gas leaving hydrate separators' is as much as 150 F below the separator temperature. This paper presents the reasons for the observed differences between the equilibrium temperatures and the dew point temperatures. Descriptions of the dew point determination by the Bureau of Mines and ASTM tester3 indicate that the dew point is taken as the temperature at which liquid water droplets first begin to appear on the cooled mirror surface even though the temperatures involved are below that required for the formation of gas hydrates or ice. PRESSURE-TEMPERATURE DIAGRAM FOR METHANE-WATEK SYSTEM Fig. 1 presents a schematic pressure-temperature diagram for the methane-water system" for some constant pressure between the critical pressures of pure methane and pure water i.e., pressures frequently encountered in pipeline operations. The possible equilibrium relations are shown by the heavy solid lines. Curve AE represents the saturated water content or dew point of gas in equilibrium with a water-rich liquid solution while curve EF represents the dew point of gas in equilibrium with hydrates. In addition the dotted line DE labelled "metastable dew point" is introduced to explain the apparent discrepancy betwceen the dew point determination and gas-hydrate equilibria. Thermodynamics place certain restrictions on the location of line DE6, namely, that (1) the concentration of water along the line DE be greater than the concentration of water along EF or that the metastable line split the angle formed by the intersection of line GE and EF

Jan 1, 1956

By Randolph H. Schnitzel

MARINGER and schwopel have investigated the internal friction of high-purity molybdenum. After light tensile deformation, they observed internal-friction peaks at about 230° to 290°C, 310" to 370°C, and 820° to 870°C, which they have attributed to the interstitials carbon and nitrogen, and to stress relaxation across grain boundaries, respectively. The electron-beam melting technique has been successfully applied to refractory metals including molybdenum. By this technique single crystals and higher-purity levels than those of commercial molybdenum are readily obtained. Since electron-beam processed molybdenum possesses such desirable qualities, it seems reasonable to determine: u) if internal-friction peaks do exist in these single crystals, and b) if so, whether or not these peaks can possibly be attributed to the motion of specific interstitials. The molybdenum crystal used in this investigation received four melting passes in the electron-beam furnace. This crystal was about 11 in. long and had an orientation 4 deg from the [loo]. The process of making wire consisted of grinding the crystal rod to a diameter of 0.040 in. and then electropolishing to a final diameter of 0.030 in. Since Maringer and schwopel have indicated that the peak at 230" to 290°C may be due to the presence of carbon, the wire was cut into two equal lengths and one length was carburized prior to the internal-friction measurements. The critical condition necessary for the controlled addition of carbon proved to be a difficult problem. Therefore, a simpler nonequilibrium method was used. This consisted of carburizing at 2000°C in graphite powder to obtain a case, annealing at higher temperatures in vacuum to partially dissolve carbon into the molybdenum, and then removing the remaining case by dissolving it elec-trolytically. After this treatment, metallographic examination of a small section of the specimen revealed carbides in the matrix. Vacuum fusion and carbon analyses for both the virgin (as melted) and carburized specimens are given in Table I. Internal-friction measurements of these specimens were conducted in an apparatus of conventional

Jan 1, 1964

By A. C. Dorenfeld

Ores of the Mammoth mining district, some 45 miles northeast of Tucson, Arizona, are treated by Mammoth-St. Anthony, Ltd. The ores now treated come from a complex system of veins and faults, comprising three mines, in close proximity: The Mohawk, Mammoth and Collins. The ore treated in the past was oxide ore, which contains economic amounts of gold, silver, lead, molybdenum, and vanadium (as wulfenite and vanadanite). The lead-zinc sulphide ore has never been treated before. The Ore The sulphide ore contains galena, sphalerite, marmatite, pyrite and some chal-copyrite, covellite, chalcocite and bornite, as well as small amounts of gold and silver. The value of the ore is principally in the lead and zinc content. The lead-zinc sulphides are substantially liberated at a minus 65-mesh grind. However, a large part of the chalcopyrite and other copper minerals is not freed, but remains as pin points on the sphalerite. Economically, the copper is unimportant. The gangue is a rhyolite granite, with very little limestone. There is no molybdenum or vanadikm in the sulphide ore. History of Sulphide Treatment Test work on samples of the sulphide ore was conducted by several equipment companies, the Arizona Bureau of Mines and the company's laboratory. Results of this test work indicated that for some reason, which at the time could not be explained, recoveries would be only about 65 per cent lead and 50 per cent zinc. Notwithstanding this, because of the nation's need for metals, the management built a 150-ton treatment plant. The mill was started in June 1942. During December 1942, using the standard method of treating lead-zinc ore, the monthly results were as shown in Table I. These results were poor. Too much lead was in the zinc concentrate, and too much zinc in the lead concentrate. It should be noted here. that prior to December attempts were made to depress the sphalerite with large and varied amounts of cyanide, zinc sulphate, and sodium sulphite with poor results.

Jan 1, 1947

By Richard Lee

SINCE the economics in the blast furnace resulting from enriching iron ores are so great, much attention, has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods . of agglomeration and sintering, of more or less value, have been put 'into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the substance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the sides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 10, 1913