Search Documents

By Bobby Dupree

I remember a big problem with a seismograph in the winter two years ago. In response to a citizen’s complaint I placed a transducer near the corner of a two-story home. It was a pretty nice day for the winter months, the people were pleasant, and I had no problems digging a hole to place the transducer.

Jan 1, 2004

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

Carlisle: An old friend and good friend, Alan Bateman, is the Silliman Professor of Geology Emeritus at Yale and editor of the Journal of Economic Geology. Now, Alan, let's start off by telling us something about how you became interested in copper. Bateman: Well, after I left Yale in 1913, I was appointed one of the field members of the Secondary Enrichment Investigation. We spent three years in the field studying all the copper deposits of North America, trying to find out how secondary copper enrichment took place. As part of this investigation, I went up to Kennecott, Alaska, in 1916. After the trip I was asked by the president of the company to become consulting geologist to them. I accepted his offer, and to this day I'm still consulting geologist to the Kennecott Copper Corp. Up at Kennecott, there were both Henry Krumb and my good friend Henry DeWitt Smith, who was general superintendent. He and I had been together at Yale, and I had ushered at his wedding. Interestingly enough, Henry took his bride to Alaska and I took mine there two months later. My assistant was Don McLaughlin, and I think that was his first experience in a mining camp. We published a paper on Kennecott together and cemented a friendship lasting to this day.

Jan 11, 1964

By C J. N Wilson

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c.0.28 m3 s-1. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust that precludes the development of long term magmatic cycles at Taupo. Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By Michael Rieber

In this study a generalized specification and costing model for high tonnage coal carrying conveyor belts of 3.5 to 100 miles is presented. These belt systems, in modular units or flights, of up to 9 miles in length can be considered in terms of gathering systems. The study format is sufficiently open to allow users to insert their own requirements and parameters. A specific case study is provided. Because conveyor belts are feasible almost anywhere, this study has not investigated any specific route or geographic location. Rather, it has concentrated on setting up an heuristic programming model for conveyor belt facility optimization and cost minimization. The analysis starts with the principle factors involved in the design of the system and their optimization for various cases. This is followed, in Section 5.4, with a factor by factor cost analysis based on industry data and the preceding optimization. The next step is the development of both facility and costing models suitable for computer analysis. Logic flow diagrams are presented at each major analytic step.

Jan 1, 1977

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By R. H. Hiltz

One of the major hazards in underground coal mining is fire. The inherent hazard of fire is exaggerated by the nature of coal mining restricted areas, the highly combustible nature of coal itself, and a potential for explosive concentrations or dust and gas in the air it becomes imperative therefore to make every effort to eliminate the causes of fires, while providing the most effective means possible to control and extinguish those fires which may occur it has been demonstrated by prior work that the problem of control increases in proportion to the time necessary to institute control procedures. There are several areas of underground coal mining with obvious fire potential. Some of these, like belt heads, have reliantly undergone improvements in standby fire control devices Others, although having fire suppression systems available to them, have not received as complete a systematic study of their problems. Face machinery, particularly those without a water supply, falls in this latter category.

Jan 1, 1973

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By L. A. Haas

A kinetic study of the carbon deposition reaction was undertaken by the Bureau of Mines as part of a broad investigation of metallurgical reactions in the iron ore blast furnace. The disproportionation of carbon monoxide on iron pellets was investigated at carbon monoxide pressures between 0.5 and 2 atmospheres (absolute) and temperatures from 400° to 1,075° C. Gas flow in the range from 0.25 to 0.85 standard liter per minute was found to have little effect on the reaction velocity. The addition of nitrogen and helium to caron monoxide exerted only a dilution effect on the rate of carbon deposition. However, an addition of 1 percent hydrogen increased the rate about 100 times. Small amounts of carbon dioxide in the inlet gas exerted little effect on the rate of carbon deposition. The maximum rate for carbon deposition in the first 2 hours occurred at 550° C. The apparent molar activation energies at various stages of the reaction were found to vary from 13 kcal initially to 36 kcal during the latter stages of the reaction. The reaction rate behavior was tentatively explained by an adsorption step followed by the diffusion of iron through a shell of inactive iron carbide.

Jan 1, 1968