Search Documents

By Tim Ross

Several shear failures were observed in Shaft #1 at the Mountain Coal Company, LLC, West Elk Mine, after mining longwall Panel 23, 1,100 ft to the east of Shaft #1. It was speculated that this shear damage could be related to differential ground movement caused by in situ stress relief from the ?stress shadow? of the caved zone above longwall Panel 23. A numerical study was conducted to assess the possibility of the shaft shear damage being caused by in situ stress relief and the potential for additional damage to Shaft #1 and two other nearby shafts, due to mining nearby longwall Panel 24. Three-dimensional (3D) models were built in FLAC3D to simulate past and future mining near shafts, the estimated local anisotropic and directional horizontal stresses, and the overlying variable surface topography. The numerical analyses indicated that stress relief due to mining Panel 23 caused the shear damage to Shaft #1and that additional damage to Shaft #1 and the other two shafts, would likely result from mining longwall Panel 24. Additional shear damage was documented in Shaft #1 when longwall Panel 24 was mined, confirming the results of the numerical analyses.

Jan 1, 2006

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Joseph J. Mgumbwa

Pillars are any structures left between two or more underground openings. The stability of pillars is normally considered to depend on shape (defined by width to height ratio), rock mass strength, extraction ratio, in situ stresses and the gross structural features (i.e. joints, contacts, faults etc). Recent experience has shown that pillar stability is also controlled by the relative orientation of the orebody with respect to the in situ principal stress. In inclined orebodies, pillars are loaded in compression and shear, thus creating unsymmetrical stress distribution. Failure mechanisms of these pillars are little known. This paper investigates the failure mechanisms of pillars under shear loading. Two dimensional elastic numerical modeling was used to examine the behavior of pillars in different orebody inclinations relative to the major farfield stress orientation. First, the paper reviews pillar design approaches including the empirical pillar design chart and uses numerical modeling to investigate the effect of the major farfield stress orientation on pillar stability. It is concluded that the empirical pillar design chart be used with caution, and that for orebodies under shear loading mine planning and design should take this into consideration since such geometrical orebody/stress relations put mine structures at higher risk of instability.

Oct 1, 2010

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

The Porgera gold deposit is an epithermal gold base-metal deposit located in the Enga Province of Papua New Guinea. Gold-silver-sphalerite-galena-pyrite mineralisation is related to stocks and dykes of dioritic composition which have intruded a series of folded marine sediments, mainly shales and siltstones, often with calcareous and carbonaceous horizons, of middle Jurassic to middle Eocene age. The most intensely mineralised zone is at Waruwari Hill, where the mineralisation occurs predominantly as massive mixed sulphide veins, and less frequently as quartz-chlorite veins and as disseminations. Mineralisation occurs in all rock types and several phases of mineralisation have been recognised.

Jan 1, 1980

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

Study on Mechanism of Sphalerite Flotation in the Presence of Main Metal Ions by Molecular Mechanics

Sep 13, 2010

The newly implemented mineral law framework exacerbated the need to clarify the roles and responsibilities of mine and land surveyors in the preparation and registration of plans and diagrams. The main concern is that survey tasks may be performed by persons who are not considered competent under the different laws. The methodology used was to analyse historic and present legislation on the issue in order to formulate a narrow interpretation of the current requirements. The major findings are tabulated to present a summary of who is responsible for which areas of survey.

Jan 1, 2010

By Blott S. F

The smelting plant and equipment at Mount Isa, as originally designed and built, was described by J. M. Callow (1) *.F. A. Forward (2) described alterations and additions to the plant and discussed the metallurgy of mixed carbonate-sulphide concentrates at Mount Isa, prior to 1933, in the Proceedings of this Institute.In 1933, A. F. McAskill (3) gave full mechanical details of the plant in a paper presented to the Institution of Engineers, Aust.FLOW SHEETSFig. No. 1 represents the present general flow sheet. Forward's (2) flow sheet is reproduced here as Fig. lA, and will serve for comparison in depicting subsequent deletions from, and alterations and additions to, the plant.Fig. No. 2 presents the daily tonnage flow sheet of 1939 practice.ALTERATIONS SINCE 1933General. Many changes in metallurgy and operation have taken place, particularly subsequent to March, 1935, when the treatment of a mixture of carbonate and sulphide ores was discontinued and the mill commenced operating on all-sulphide ore. This alteration brought about the elimination of gravity concentration-Jigs and Tables and resulted in the production of all-floatation concentrates of a very fine sizing. Refer Table No. 2, page?) Radical changes in the analyses and physical nature of concentrates also followed (see Table Nos. 1 & 2, page ?) and, similarly, radical changes in the smelting plant have been slowly brought about.

Jan 1, 1939

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

Cyclone Process for Heavy Metals Decontamination of Sediments

Sep 13, 2010