Search Documents

By A P. Tinnelly

This paper explores the structural/physical and policy based issues that have lead to the apparent resource conflict between Forestry and Mining on the West Coast. Both industries are important to the West Coast and bear many similarities, particularly at the corporate end of the mining scale. However there are very distinct structural differences which set the scene for friction at the boundaries. Examples of how mining impacts upon forestry illustrate where some of the friction arises and provides some insight as to where some solutions are or may be found.

Jan 1, 1996

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) conducted a series of large-scale experiments to evaluate the effectiveness of optical flame detectors, photoelectric smoke detectors, and combined ionization and photo­electric smoke detectors for rapidly detecting mining equipment cab fires. The detec­tor alarm times were then used to trigger the discharge of a fire inerting system inside the cab to suppress cab material fires. This paper discusses the types of fire detectors tested, the experiments that Were conducted, and the results that were obtained. Con-" elusions are that rapid detection of equipment cab fires can be achieved to trigger the discharge of a fire inerting system inside the cab to protect the operator in the cab.

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By José Cuadros

"El presente trabajo señala el proceso de evolución del método de minado en la mina Chupa, perteneciente a la unidad minera de Iscaycruz. La evolución del método de minado se determinó por la búsqueda de mejores condiciones de seguridad y eficiencia en la operación. En ese sentido, los resultados logrados con cada una de las alternativas de minado por subniveles, indica que se ha logrado optimizar las diferentes variables mineras y cumplir con el plan estratégico de Empresa Minera Iscaycruz S.A. (EMISA). Para cumplir con el citado plan estratégico, se debe optimizar el método de minado de Chupa, a través de una mayor producción a un menor costo,así como del aprovecho de las labores de desarrollo y preparación ejecutadas según el planeamiento inicial del minado. Por ello, la secuencia del avance del minado y la reestructuración del sistema de relleno de la mina son los aspectos importantes para lograr este objetivo. "

Jul 31, 2003

By J. L. Potter

An inert-gas fusion technique was applied by the Bureau of Mines to the oxygen analysis of mixed-fluoride electrolytes used in electrowinning uranium and the rare-earth metals. Method development included: (1) Thermodynamic and experimental evaluation of the temperature required to quantitatively remove oxygen from a fluoride melt; (2) installation of a water and an acid trap to entrain the volatilized fluorides; (3) development of a suitable sample-preparation technique for the heterogeneous fluoride baths in which both pulverizing and pelletizing were necessary to achieve reproducible results; (4) comparison of platinum flux and dry crucible techniques, which showed that the use of platinum was not necessary. The accuracy of the method was evaluated by analyzing fluoride baths containing known amounts of oxygen added as the metal oxide. In the 0.05-to 0.5-percent range, the relative error was about ±5 percent.

Jan 1, 1962

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By A. E. Lewis

The emphasis of this paper is on the characterization and testing of the slag produced by a secondary lead refinery. This work forms part of a broader investigation aimed at reducing loss of valuable product from the process as well as minimizing the environmental impact of the process wastes. It was this work that led to a critical examination of the standard waste classification tests. Characterization of the slag was carried out using a number of complementary techniques. In the broader context, the slag characterization aided in identifying process deficiencies and thus was a critical tool in suggesting potential for process optimization. For this study, the slag characterization provided a relatively comprehensive picture of the composition and properties of the slag, which facilitated understanding the behaviour of the slag under batch test conditions. On the basis of quantity of hazardous components alone, the slag is hazardous according to South African Acceptable Risk Limits (ARL). However, when both the quantity and the leach potential of the hazardous components is taken into account, standard waste tests carried out by three independent agencies indicate that the slag should not be classified as hazardous according to local regulations. Also, according to United States Environmental Protection Agency (US EPA) limits, which are independent of the quantity of the waste, the slag would not be classified as hazardous. The standard waste tests used by the independent agencies was the Toxicity Characteristic Leach Procedure (TCLP), a test which was developed by the US EPA to classify hazardous wastes. One of the requirements of this batch test is that it should be quick, simple to carry out and that the results should be reproducible. Previously, the applicability of the TCLP test to mineral processing and metallurgical wastes has been challenged on a number of points. Additional testing of the slag was carried out using both the TCLP and the Synthetic Precipitation Leach Procedure (SPLP) recommended by the American National Mining Association as being more appropriate for mineral processing wastes. The particular physical and chemical characteristics of the secondary lead slag highlighted additional limitations of both the TCLP and SPLP tests as standard laboratory batch procedures. Keywords: environmental protection, secondary lead processing, slag, leach testing, TCLP, SPLP, ARL, hazardous waste, batch tests

Jan 1, 2000

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Jan 1, 1993

By G. E. Agar, W. B. Kipkie, V. K. Drylie

"This paper describes mineral processing test work on drill core samples from an ilmenite deposit in Terrebonne County just north of Montreal.Mineralogical examination showed that the intimate associa¬tion between ilmenite and hematite precluded their separation. The maximum concentrate grade was therefore limited to 22.9% Ti. Liberation of gangue from the hemo-ilmenite grains occurred around 400 µm, a size which proved to be too coarse for recovery by flotation.Other physical separation techniques, such as elec¬trodynamic, magnetic and jigging, were tried in order to take advantage of the relatively coarse liberation size. An all-flotation procedure and a combination of jigging and flotation yielded similar separations.IntroductionInco Metals Company, through its subsidiary Canico, optioned an ilmenite deposit in Terrebonne County, just north of Montreal, and conducted a drilling campaign to confirm previous geological assessments of the deposit and to provide core samples for mineralogical study. Parts of these core samples were used for mineral processing studies, which will be described in this report. The objective was to identify suitable upgrading procedures, to determine the optimum combination of concentrate grade and recovery, and to provide suitable batches of concentrate for further treatment."

Jan 1, 1980

The preeipitation of dissolved lead from a strong brine by metallic iron is a chemically controlled, first order reaction. The precipitation rate is sensitive to changes in chloride concentration and temperature. The precipitation of dissolved silver is a diffusion controlled, first order reaction. The precipitation rate is insensitive to changes in chloride concentration and temperature.INTRODUCTIONLead and silver sulphates can be extracted from electrolytic zinc plant tailings, or residues, by leaching with strong brine solutions, the lead and silver going into solution as complex chlorides. One of the methods which can then be used to recover the dissolved lead and silver is to precipitate them with metallic iron. The deposition reactions which take place are of the type Pb++ Fe - Fe++ Pb............ (a)To fit such a method of precipitation successfully into a practical flowsheet it is necessary to have some knowledge of the kinetics of the various reactions, Le. to know how the precipitation rates vary with temperature, brine and metal concentrations, and so on. Reaction rates are also needed to design suitable precipitation vessels. However, when examining the possibility of using a brine leaching process to extract the lead and silver from the residue produced at the Risdon plant of the Electrolytic Zinc Co. of Australasia, it was found that, although the use of metallic iron to recover lead and silver from the pregnant brine had been reported by Ralston (1924) and by TrumbulI, Hardiek and Lawford (1948), very little was known about the precipitation reactions. Consequently a laboratory investigation was undertaken, and this paper covers those aspects considered to be...

Jan 1, 1961

By Franciszek Letowski

"Recovery of precious metals associated with a sulphidic matrix has an important economic effect on complex sulphide ore treatment. Because a significant portion of the silver and gold associated with pyrite are rejected to tailings during the selective flotation of pyritic Zn-Pb-Cu ore, other ore processing routes have been investigated.Direct leaching of the ore with ferric sulphate solution followed by separation of different components of the solid suspension by flotation was applied. Such a process allows for: production of zinc sulphate solution; transformation of galena PbS to insoluble lead sulphate PbS04 and its accumulation in a non-floatable fraction together with precipitated geothite FeOOH and other insoluble gangue minerals; separation of sulphur and non-decomposed sulphides in the floatable fraction.Laboratory research carried out on the ore samples from an Alaskan pyritic deposit from the Delta region indicates that gold and silver are mostly concentrated in the floatable fraction.Total recovery of zinc from the ore attains 96.5% to 98.5% after ferric sulphate leaching. About 85% of copper was extracted from the ore during the ferric sulphate and subsequent ferric chloride leaching, and about 6% of the copper remained in the non-floatable fraction and mixed fraction during the leaching-flotation step. Extraction of lead from the nonfloatable fraction during leaching with calcium chloride solution attained 98% to 99%. Extraction of silver from the floatable fraction during leaching with ferric chloride solution reached 98%. Extraction of gold from the floatable fraction during cyanide or thiourea leaching reached 71% to 89%. The results of the laboratory research are presented."

Jan 1, 1987

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985