Search Documents

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,'. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955

By Vernon C. Davis

In initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining. The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost. This report, is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges. Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage. In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested. Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes. Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows paral-lel to one of the series of joint planes. Methods of detonation made little difference in breakage; but the milli-delay caps produced the best conditions for moving the broken rocks.

Jan 1, 1953

By S. R. Brown

A number of relatively recent factors associated with the design of new metallurgical processing plants have made the effective training of operators a requirement for a successful start-up. Some of these factors include large capital investment in a minimum of processing lines, highly complex process control systems, and stringent regulations on plant effluent, to name a few. More than ever, operating mistakes during the start-up phase can lead to substantial delays in achieving design production, as well as problems with government authorities if permit limits are exceeded. The only way to assure your return on plant investment is to ensure new plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted for plant operators and foreman, written by experienced operating personnel, is the only effective way to provide the necessary information for start-up-related training.

Jan 1, 1995

By C. F. Willis

The problem of the curtailment of forces in large numbers does not often come to employment departments and is, therefore, a problem that many departments are not prepared to handle intelligently. Those companies that are able to measure the individual efficiency of each man would probably lay off men according to their individual ability, irrespective of dependents, citizenship, or other considerations. During the war when labor was scarce, the business of the employment manager in industry was hiring men and carefully placing them where they were best fitted to work. The careful selection of employees had developed to a considerable extent before the war, and was becoming a recognized science. In the last few months, however, the cancelation of copper contracts, the accumulation of large stocks, the necessary curtailment of production because the copper could not be sold, and the lack of any immediate prospects of' the copper market opening, have led to a universal reduction of forces, and the problem that industry now confronts is that of discharging rather than employing. The problem has been aggravated by the cancellation of contracts in many war industries with the consequent turning loose of hundreds of thousands of men, a great amount of unemployment, and the return of the soldiers and sailors. The problem has now become one of reduction of working force with the least hardship and the least injustice, and yet caring for the soldiers, sailors, and marines who have been in the service of the government for nearly 2 years, and are now returning to their pre-war positions. The Copper Queen Branch of the Phelps Dodge Corpn., operating at Bisbee, Arb., found it necessary, like all of the other copper companies of the country, to reduce its force materially. In making this reduction it was, after due consideration, decided to classify employees with respect to dependents, length of service, and citizenship. The question of individual efficiency or workmanship was not considered. Copper produced to sell at 26 c. a lb. has been selling at under 15 c., and very little copper is being sold at all. Practically every copper producer in the country has enormous stocks on hand, and it would be profitable,

Jan 1, 1920

By D. S. Yantek, R. J. Matetic, A. K. Smith, E. D. Thimons, J. Srednicki

In a 2007 report to the U.S. Congress, the Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) stated that built-in-place refuge alternatives (BIP RAs) provide significant advantages over mobile refuge alternatives. At present, the requirement to locate refuge alternatives within 305 m (1,000 ft) of working faces makes BIP RAs impractical in most coal mines. BIP RAs would be practical if three issues are addressed: (1) allowing BIP RAs to be located at greater distances from the working face, (2) developing a reliable process for the design and approval of BIP RA stoppings that meet the 0.1-MPa (15-psi) design criteria, and (3) developing systems that reliably deliver breathable air to the refuge alternative. In 2015, NIOSH OMSHR conducted a study of these three issues and issued a report. In the report, justification was provided for allowing the placement of BIP RAs at greater distances from the working face than the currently mandated 305 m (1,000 ft), guidelines were developed that could be used by industry when submitting BIP RA stopping design applications for approval which are patterned after the Mine Safety and Health Administration guidelines for coal mine seal design applications, and insights were provided into options for providing a reliable supply of clean, breathable air to BIP RAs. This paper presents a summary of the study’s findings and also addresses issues discovered during the building and designing of a BIP RA that OMSHR researchers constructed in NIOSH’s Experimental Coal Mine in Pittsburgh to research the testing and improving of BIP RAs. These issues include several issues related to the delivery, distribution and exhaust of ventilation air to the BIP RA and some general construction issues that require further investigation.

Jan 1, 2016

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By J. F. Barry

Newmont Mining Corporation and Barrick Goldstrike Mines, Inc. concluded an exchange of land and reserves in an agreement signed May 3, 1999.This exchange of assets allowed Newmont to develop the Deep Post underground mine from within Barrick’s Betze-Post open pit, thus reducing capital expenditures, lowering operating costs, and advancing the production schedule by nearly three years. Based on previous experience, Newmont is confident that the Deep Post underground mine can be successfully developed and operated within a large, active, open pit mine. The project also faces difficult geotechnical conditions including weak ground, scattered pockets of groundwater, and elevated rock temperatures.

Jan 1, 2000

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By D. A. Reynolds

Yields of ammonium sulfate obtained in the carbonization of coal frequently vary from plant to plant, because ammonia is an unstable compound at high temperatures and therefore sensitive, to changes in carbonizing conditions. Differences in byproduct yields of ammonium sulfate obtained at different plants generally are accounted for by variations in plant procedure, either in preparing the coal or in its carbonization. However, technicians of one large corporation,- which frequently obtained higher yields of ammonium sulfate in its Alabama plants than ever were attained in its Ohio plants, "could not reconcile the differences in yields with their plant operations. These investigators suspected that the Alabama, coal used in their southern plant yielded more ammonia because its composition differed inherently from that of the Pennsylvania and West Virginia coals fused in their Ohio plants, although this concept could not be proved readily in their large-scale operations. Their view is supported by experimental data obtained A Beau of Mines-American Gas Association (BM-AGA) carbonization tests) -21 of a large number of coals including those carbonized commercially in Alabama and Ohio.

Jan 1, 1949

By James R. Gingery, Byron Foster, Bret Lingwall

While microzonation and setbacks are the typical mitigation for structures exposed to surface fault rupture hazards, lifelines and lifeline facilities are not easily relocated to avoid faulting. In these cases, other remedial measures including ground improvement may be warranted. Deep soil mixing ground improvement was used in this case to mitigate surface fault rupture and liquefaction hazards for a pump station at a wastewater treatment plant with wet wells up to 36-feet (11-m) deep. Paleoseismic field investigations were performed to characterize the site, then deterministic and probabilistic fault rupture displacement estimates were made and used to develop design scenarios. The fault rupture mitigation design consisted of a solid block of DSM encompassing and protecting the pump station and its wet wells. Three dimensional soil-structure interaction numerical modeling of the fault rupture scenarios was performed as part of the design. The analyses showed the fault rupture displacements could be diverted by the DSM and that satisfactory structure performance could be achieved. The design required construction of a large 100 percent replacement ratio block of DSM with a compressive strength of 500 psi. Aspects of construction of this DSM block are discussed.

Sep 8, 2021

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Abrahan Barriga

The present study demonstrates the feasibility of the ultrafine grinding and atmospheric leaching process applied to refractory gold concentrates from Salave Project located in northern Spain. At bench scale, it was found acceptable sulfide oxidation was about 84-85% and CIL gold recoveries between 95-96% applying specific energy consumption between 30 and 60 kWh/t during ultrafine grinding. The atmospheric oxidation of the sulfide concentrate was controlled between pH 4.4 and 4.8 with a mixture 90/10 of CaCO3/NaCO3 with residence time of 48 hours for the atmospheric oxidation and 30 hours residence time for the CIL process.

Sep 30, 2022

By Taisuke Sakakibara, Shinya Suzuki, Tatsuya Kato, Chiharu Tokoro, Kenichi Muto

Surface complexation using a diffuse layer model were constructed for arsenic (As(V)), zinc (Zn(II)) and silicate (Si(IV)) for aluminum hydroxide in the co-precipitation process. From experimental investigations using isotherms, zeta potential measurement and XRD analysis, it was confirmed that co-precipitation involved not only surface complexation but also surface precipitation. However, surface complexation was major mechanism for As(V), Zn(II) and Si(IV) removal under the target removal level of the Japanese effluent standard. In surface complexation modeling, exchange capacity of aluminum hydroxide was determined from specific surface area obtained from experimental measurement and site density obtained from reference. Surface complexation coefficients were determined by fitting the removal property and sorption isotherm obtained from co-precipitation experiments. These parameters were in agreement with the numerical parameters found by Karamalidis and Dzombak (2010) who reported a database of adsorption equilibrium constants for gibbsite. The surface complexation models constructed in this study were applied to neutralization process of an actual AMD treatment. Our model could successfully represent the pH edges for As(V), Zn(II) and Si(IV) in the neutralization of AMD.

Jan 1, 2015

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By A. Rodriguez-Prado, P. Kuschk, R. L. Legge, W. C. Lennox

Using constructed wetlands to chemically reduce hexavalent chromium Cr(VI) to Cr(III) from industrial and mining wastewater has proven to be feasible and efficient. Applying first-order kinetics to describe the process is simple, but in some cases a more accurate model is required to reflect the process. This paper studies the feasibility of using non–first-order kinetics to describe the reduction process. Results indicate that half- and second-order kinetics adequately described Cr(VI) reduction in laboratory wetland mesocosms. The organic carbon content played a relevant role, whether it was built up by plant growth or spiked into the feed water.

Jan 1, 2014

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014