Search Documents

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

Lime and cement manufacturing has a proud history in Otago, with the earliest lime kilns appearing around 1849 at Caversham and Kaikorai in Dunedin . At Dunback or Makareao (to be precise) three well-type kilns were built by the government in 1899. In 1909 these kilns were leased to the then Milburn Lime and Cement Company. They erected a large brick Schmatolla kiln in 1909, elliptical in plan and fired by coal gas. The kiln operated up until 1944 before being left derelict. The quarry which supplied the kiln also supplied the Burnside Cement works from 1929 up until its closure in 1988. The quarry was shifted to the top of the hill in the 1950s.

Jan 1, 1992

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By Christian Heili

In 1991 the Government of the Republic of Zambia passed legislation providing for the privatisation of Zambia Consolidated Copper Mines Limited (ZCCM). The newly formed Mining Companies, established after nearly a decade of difficult and protracted negotiations on such matters as, cash at close; retained percentage interest by ZCCM; equity investment; future investment commitment and tax concessions, were faced with great internal challenges and a harsh external environment. There was a convergence of a number of negative forces that had and will continue to have an impact on the mining environment in Zambia. The most crucial of these being, the competitive pressures of the global economy, fluctuating copper price and the prevailing HIV/AIDS pandemic. In the short period after privatisation, the Industry has seen the collapse of Binani Industries (Luanshya Mine), the withdrawal of Anglo America Corporation from Konkola Copper Mines Plc and the disposal of Chambishi Cobalt and Acid Plants by Anglovaal Mining Ltd. The objective of this paper is to provide a theoretical and practically researched foundation, which may be used to assist Zambian Mining Companies in making informed decisions on the issue of Strategic Outsourcing and the degree to which this may support the successful and sustainable growth of the Zambian Copper Mining Industry. If judiciously implemented, Strategic Outsourcing has the potential to generate a practical business valuation and process to assist Mine Management in the achievement of their business goals and consequently the return on investment to their Shareholders.

Jan 1, 2005

By E. H. Burroughs, M. J. Gavin

The references in the following compilation are selected chiefly from the literature of the years 1915-1920 , though a few of the more valuable standard works published before that period have necessarily been included . References to many articles have been omitted purposely , because the material covered by them is duplicated in publications included in the bibliography . It is manifestly impossible for the Bureau of Mines either to recommend or adversely criticize the statements of the various writers , particularly as to cost and profit estimates in articles referring to American shales , but it is hoped that the investigator will use caution in considering such statements , as it is well known that much of the literature on this subject has been published for promotion purposes and is therefore over- enthusiastic . Bearing this fact in mind , the reader should be able to judge for himself the reliability or usefulness of these articles .

Sep 1, 1921

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By Bruce McDonald

This report contains the Phase I findings of a study to select and test devices for preventing lack of alertness in haulage truck drivers. The extent of the problem was determined by visiting surface metal and nonmetal mines, interviewing drivers and safety personnel and reviewing accident reports. A number of devices for detecting a lack of alertness were considered and three were recommended for testing in actual operation.

Jan 1, 1977

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

Jan 1, 1970

By K G. Harding, E L. Haggard, C M. Sheridan

Mining is a water intensive sector, contributing to declining water resource quality around the world. Improvements to current mine water management practices can help reduce the amount of water utilised by the mining sector and the impact on water resources. Creating a water account can help companies understand water use in their operations and identify areas where water reduction is possible. Water accounting methods include the Water Footprint Network method and the WaterMiner tool.The Water Footprint Network method is used to determine the amount of direct and indirect water used by an organisation either in a process or to manufacture a product. The total water footprint is divided into the blue, green and grey water footprints. Blue water is the amount of water abstracted from surface and ground water resources. Green water is the amount of rain water utilised. Grey water is the amount of freshwater required to assimilate the waste stream to the natural resource and still conform to ambient water quality standards.The WaterMiner tool is a program available via the internet, which can be used to model water use of mineral processing sites. The program reports the amount of raw, worked and treated water used by the process and recommends flows that can be added to reduce the amount of fresh water required by the process.To gain information on mine water management practices in South Africa, a water account for a platinum mine was developed using the Water Footprint Network method and WaterMiner tool. Based on the results, suggestions to reduce the amount of fresh water utilised are made.CITATION:Haggard, E L, Sheridan, C M and Harding, K G, 2013. Water footprint for a South African platinum mine, in Proceedings Water in Mining 2013 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Jan 1, 1989

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By AIME AIME

THE 122d meeting of the Institute was held in the Lake. Superior Copper and Iron Country Aug. 20 to Sept. 3, 1920 with an approximate registration of 1100 members and guests. This is the &apos;first visit of, the Institute to this vicinity since 1904 although previously it held meetings there every six or, seven years. &apos;The eastern party assembled at Buffalo and sailed on the S. S. "Tionesta ". on Friday morning, Aug. 20, arriving at Houghton, Mich., Monday, Aug. 23. En route stops were made at Detroit, where sightseeing auto trips were taken, and at Mackinac Island, where a short stop permitted a visit to the picturesque and historic Fort Mackinac.

Jan 1, 1920

By C. L. Emery, A. V. Corlett

"The stress equilibrium is disturbed in a body of rock by a mine opening and is restored by a redistribution of the stresses around the opening. The pattern of the redistribution of unilateral stress around an opening has been established by mathematical analysis and photoelastic measurements. The pattern for multilateral stress is found by superimposition of unilateral fields. The mathematical analysts do not use the elastic moduli as parameters and they are not significant in photoelastic work. The medium is isotropic. The concept of unilateral stress from vertical loading and the classical pattern of its stress distribution around openings does not explain commonly observed failures around the perimeters of mine openings. They show evidence of compression where tension is postulated.When it is recognized that few minerals and perhaps no rocks are Hooke Solids, most rocks must be St. Venant Solids. The components have varying degrees of elasticity and viscosity. The assembly will be-have elastically to rupture under shock loading, but when loaded short of rupture will adjust viscously to equilibrium. Similarly, the highly elastic components may initiate rupture before equilibrium can be established when stress is instantaneously relieved. Polycrystalline adjustments may produce permanent deformation. The mechanics of consolidation, especially in sedimentary deposits, ac-quire a stress component normal to the direction of compaction which can exceed that of the loading. It is one source of prestress. There are others. The principles of prestress design are based on the normal beam reactions, modified by a built-in compression in the lower chord. When the beam is loaded to design limits, the lower chord retains some compression and the whole beam depth is effective in compression. Some of the . common evidences of failure in compression over a mine opening can be duplicated in a prestressed experimental model.When the triaxial stress pattern is recognized and suitable measuring techniques are devised, mine design can be done on a rational basis."

Jan 1, 1959

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963