Search Documents

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

Jan 1, 1967

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P205 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By James R. Kunkel

The paper point out the use about of robust water-balance method for sizing heap leach solution ponds and water reservoirs. In this sense, using a robust water-balance method to size storage ponds and reservoirs as well as to calculate operational water demands is important to assess the interactions between operational and climatological variables for the project.

Sep 13, 2001

By Douglas A. Anderson

The simplest method used to predict ground vibration from blasting is scaled distance -the distance from a blast divided by the square root of the Pounds per delay. Pounds per delay is defined as the number of pounds of explosive detonated within an 8 millisecond (ms) interval. Based upon this definition, regression plots of peak particle velocity vs. scaled distance have been used to determine likely values of peak particle velocity.

Jan 1, 1989

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By A. P. E. Dirige

Extensive field study has been performed to assess the capabilities of thin sprayon liners (TSLs) and conventional spray-on support systems for preventing rock and support material damage that often results due to mining-induced rockbursts. Support performance was studied using field scale explosive detonation trials to simulate dynamic failure effects that are known to develop during typical rockburst events. Multiple seismic and high speed photographic monitoring techniques were used to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion, and support liner survivability characteristics. Results of this study have demonstrated that TSL?s and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In this study, field results have been verified using numerical modeling procedures to better understand the support behaviour of TSLs when subjected to highly stressed mine environments and mining-induced rockbursts, a factor that is essential when designing any rock support system. A series of numerical modeling assessments were conducted using FLAC3D modeling of a half circular TSL-lined tunnel, influenced by anisotropic stresses and simulated mining-induced rockbursts, to investigate the support potential of TSLs under prototype conditions. The effect of a mine rockburst was simulated using the three-dimensional dynamic analysis option of FLAC3D. Results of TSL-lined tunnels in highly stressed and mine rockburst conditions indicated exceptional effectiveness of TSLs for suppressing rock deterioration resulting from stresses and rockbursts. The rock support potential of TSLs on tunnel surfaces was compared with that of thin shotcrete linings, and results indicated that thin spray-on lining products currently available may be equally as effective in support as shotcrete materials.

May 1, 2009

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

This paper examines some of the fundamental economics of mining - in particular, for optimisation studies, for production rate determination and for reserve estimates.It includes introductory discussion on the principles as to how economics drives mining investment decision-making, applicable to the optimising of pit shapes and production, or truck fleets, or any other part of the mine.The main part of this paper looks at the decision to start-up a mine and why the &apos;optimum&apos; production rate to start-up a mine is not the point of lowest cost according to traditional discounted cash flow (DCF) analysis. The optimum production rate is usually substantially less than this rate. The paper recognises the difference between typical mining investments and investments in other industries that do not have the unique characteristics of mining and the problem of uncertainty resolution. It examines the marginal revenue effects, the marginal cost of capital and the value of a real option to expand pending uncertainty resolution as determinants of optimum initial production rates.The final part of this paper looks at applying these principles to renewable and non-renewable resources. It examines mine life and reserve estimates from an economic perspective.

Dec 6, 2010

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By Bill Williamson, Doug Richmond, Kerri Kuntz, Gus Gilman, Larry Heywood

This was a description by the poet of what occurred over two centuries earlier to Hannibal’s troops as he passed through the Alps. Interestingly, the pass that many feel is the route that Hannibal chose, Col de la Traversette, is the sight of possibly the earliest avalanche mitigation known. Monastery records describe a tunnel built in 1470, near the top of the pass designed to protect pilgrims from the upper slopes. For the next several centuries, avoidance and reinforced structures were the primary tactics to defend from avalanches

Jan 1, 2009

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010