Search Documents

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By Wagner Aldeia, Duclerc Fernandes Parra, Danae Lopes Francisco, Ademar B. Lugão, Lucilene Betega de Paiva

The inorganic nanotube halloysite (HNT) is a promising type of natural occurring filler for polymers. Its characteristics, such as high aspect ratio (10–50), small size, and high strength (elasticmodulus—140GPa) suggest that HNT shave a potential use in high-performance polymer nanocomposites. Compared to other nanoclays and nanosilica the relatively low content of hydroxyl groups on their surfaces makes HNTs relatively hydrophobic, although, sometimes, this is not sufficient for guaranty a good interfacial adhesion in composite systems. Further hydrophobic treatment is required to improve HNTs compatibility with polymer matrixes, maximizing interfacial interactions. In the present study, different percentages of EPB (2,2-(1,2-ethene diyldi-4,1-phenylene) bisbenzoxazole) was used to perform anon-covalent functionalization of halloysite, based on electron transfer interactions. The functionalization is characterized by specific surface area (BET), thermogravimetric analysis (TG) and water/toluene extraction experiment.

Mar 1, 2018

By Nan C. Jensen, Oliver Bowles

Stone , the foundation of the continents and the floor of the oceans , is one of the most substantial and enduring of all substances that constitute the material universe . Stone furnished rude shelter for aboriginal man , and through all succeeding ages it has provided a lasting and serviceable structural material . Limestone is one of the most widely used building stones .

Oct 1, 1947

By M. J. Lempel

A theoretical study of the heat-transfer characteristics of a dilute gas-solids mixture in an externally heated tube is reported. Detailed equations are developed describing the system, and a numerical method is presented to solve the equations using a digital computer. The methods are applied to a system containing fine coal particles entrained in hydrogen, flowing through a hot tube. Heat-transfer coefficients and several other physical constants are evaluated in detail.

Jan 1, 1967

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By W. E. Rudolph, R. E. Baylor

DUE to its location in the Atacama Desert, one of the most barren of the earth's surfaces, Chuquicamata's water supply presents unusual problems. Yearly rain-fall averages less than one tenth of an inch at the plant. However, there are summer showers above 12,000 ft in the Cordillera to the east, the resulting run-off flowing through old river valleys buried beneath more recent volcanic formations, to be impounded within sediment-filled basins. This water emerges at springs where the outlets of these basins are blocked by lava flows, and here are formed the small streams which feed the only important river of the region, the Rio Loa. Chuquicamata's water is obtained from these springs and rivulets. [ ] The map above indicates four pipe lines from which potable and industrial water are supplied. Potable water, amounting to 4500 metric tons per day, is conveyed in the Toconce pipe line from springs 59 miles due east of Chuquicamata. This water is used not only for drinking, but also for boilers and other needs requiring high quality. For industrial water at the oxide plant, there are two 12-in. pipe lines from the Rio San Pedro, carrying a total of 17,000 metric tons per day of slightly brackish water. This water is at present used mainly for leaching and for hygienic purposes. Water Source Found For the present and future needs of the sulphide plant, it was calculated that at least 32,000 metric tons per day of make-up water would be required. For this purpose, a pipe line of 44 miles length was constructed to bring in the entire flow of the Arroyo Salado, one of the eastern tributaries of the Loa. The salt content of this water is so high (over 5000 parts per million of solubles, mostly chlorides) that it is highly detrimental to farming, and the Chilean Government had been studying projects to separate these waters from others of the Loa system in order to improve agricultural conditions in the fertile valley of Calama. So it happened that the Government was willing to award rights to the Arroyo Salado waters under agreement whereby the Mining Company removes waters from the Rio Loa system above Calama for all time. The outlet of these waters, after serving their purpose at the new concentrator and leaving the plant in tailing, is the Salar de Talabre, an old salt lake which presents fully ten square miles of surface to serve as an evaporating pan, the outlets having now been blocked by dams. Here the dry climate of Chuquicamata is a favourable factor, evaporation averaging slightly above 1/4 in. per day. The Toconce and San Pedro pipe lines have been functioning from 26 to 34 years, and through the use of special cleaning tools which were developed at the plant, as well as deaeration of the more active Toconce water, these pipes are now maintained at capacities which do not diminish as years go on. Constructing the Dam The Arroyo Salado pipe line design and construction involved certain special and interesting features, and inasmuch as this line and its intake works are solely for the needs of the new sulphide plant, more detailed description is given. The waters are impounded at a gravity dam constructed of concrete to a height of 100 ft above the river bed, keyed into the precipitous Dacite walls of the narrow canyon (barely 6-ft wide at the bottom, only 25-ft width at 50 ft above). A small secondary dam was built 100 ft down stream from the main dam, providing a pool of 15-ft depth to protect the main structure from flood flows over the spill-way during the rainy season. A system of four 36-in. syphons was designed for discharging these flood waters from the lower depths of the lake, in order to avoid eventual sedimentation behind the dam. The lake has a length of 3300 ft, and its water level is controlled by an adjustable spillway permitting draw-down of eighty inches, amounting to 41,000 metric tons of available capacity. This regulation is necessary because of wide fluctuations in stream flow between day and night due to freezing of feeders. During the construction of the dam the entire river flow was handled within a 36-in. pipe line some 2000 ft in length. As the excavations proceeded

Jan 1, 1952

By José Wilmar Calderón-Hernández

Aços inoxidáveis supermartensíticos (AISM) são aços de matriz martensítica contendo baixos teores de carbono, abaixo de 0,03%. Eles vêm sendo utilizados na indústria de óleo e gás para aplicações específicas que exigem resistência mecânica aliada a moderada resistência à corrosão. Após serem temperados para a obtenção da estrutura martensítica, esses aços são submetidos a tratamento de revenimento para alívio de tensões e melhoria das propriedades de tenacidade e ductilidade. Durante o revenimento é esperada a ocorrência de mudanças microestruturais resultantes principalmente da precipitação de diferentes fases. Tais precipitados influenciam tanto as propriedades mecânicas finais quanto a resistência à corrosão desses aços. Nesta pesquisa foi avaliada a resistência à corrosão por pite de dois AISM do tipo 13Cr5Ni2Mo, um deles contendo Nb (0,11%), através de ensaios de polarização potenciodinâmica em soluções de 0,6M NaCl sem e com adições de 0,3M e 0,6M Na2SO4. Os resultados mostraram que a adição de Na2SO4 no eletrólito contendo NaCl inibe consideravelmente a corrosão por pite. Foi constatado também que o AISM contendo Nb apresenta maior resistência à corrosão por pite nos eletrólitos de misturas de cloreto e sulfato. Além disso, os resultados mostraram que o revenimento a 575°C melhora a resistência à corrosão por pite, comparativamente ao revenimento a 600°C. O melhor potencial de pite foi obtido para o aço ao Nb, revenido a 575°C por 2h, em eletrólito 0,6Na2SO4+0,6NaCl.

Jan 16, 2018

By Donizete Lúcio de Campos

Vários estudos vêm sendo realizados em ligas com efeito de memória de forma, em especial as ligas a base NiTi devido a suas excelentes propriedades mecânicas e pronunciadas características como o Efeito Memória de Forma e a Pseudoelasticidade. A adição de terceiro elementos na liga NiTi permite alterar determinadas propriedades desta liga. Este trabalho avalia a influência do teor de Cu na liga base de NiTi. Através de análises térmicas e metalográficas observou-se redução significativa da histerese de transformação com o aumento no teor de Cu em substituição ao Ni em liga equiatômica de NiTi.

Aug 16, 2017

By Robert H. Merrill

This report summerizes the various studies made to determine the size and support of roofs in the upper shale formation, White Pine Copper Mine, Michigan. These studies were a cooperative effort of the White Pine Copper Company and the Federal Bureau of Mines. Before this investigation, the upper shale formation had been found to contain about 30 to 40 percent of the total mineralization in the ore zones. Investigators estimated that this shale could be economically mined by room-and-pillar methods, provided that the roof would stand over spans of 25 to 32 feet. The problem remained to determine the number of bolts required to safely support these spans. Unbonded fractures in the roof structure of the deposit complicated the use of laboratory methods for determining bolted roof support. Therefore, a method was devised to determine the in-place support which would consider the unbonded fractures. In this method the roofs of 3 rooms with spans of 20, 28, and 36 feet were intentionally overbolted as the rooms were mined. Following stability tests that sometimes exceeded 6 months, the bolts were selectively removed and roof sag, roof strain, and changes in bolt loads were measured concurrently. The number of bolts required for support of these spans was computed from these data.

Jan 1, 1961

By C. Cristoffanini

A real-time transient pipeline simulation was used to model the operational pressure response in the concentrate and tailings pipelines of the Minera Los Pelambres copper mine in Chile. A high-fidelity simulator was needed to train the operators on safe operation of the pipeline for different scenarios. A simulator that solves the transient equations was used to dynamically predict the pressure and flow throughout the pipeline to provide real-time responses to operational changes such as opening or closing a choke valve, or sending a water batch. Slurry rheological properties were incorporated into the model. This paper presents the technical background of the pipeline simulation model and the study of slurry properties. The paper shows the results of the transient simulation for different operating scenarios such as start-up, shutdown and leakage, by presenting the hydraulic gradient curves for each case. Finally, the paper briefly presents how the simulator was connected to an emulated control system and used to train the operator, it demonstrates the most effective tool available to learn to resolve undesirable conditions.

Feb 23, 2014

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Pedro Lilienfeld

The objective of this program was the development, design, and fabrication of six personal-sized completely self-contained dust monitors capable of real-time as well as time-averaged monitoring of the concentration of respirable particles in coal mines, in the range of 0.1 to 100 mg/m3. The operation of these monitors is based on light scattering and passive air sampling. The design stressed overall miniaturization, ruggedness, simplicity and versatility. These instruments incorporate a single-chip CMOS microprocessor to perform all signal processing, data display and storage, and timing functions. The overall dimensions of these devices are, approximately, 10 by 10 by 5 cm.

Jan 1, 1982