Search Documents

By R. W. Huber

The successful development of a titanium prototype of the 81-mm. mortar base plate for the Army Ordnance Corps is outlined in this report. Information is presented dealing with forming, forging, and machining, welding and assembly techniques, and design changes relative to this prototype. INTRODUCTION The work of the Federal Bureau of Mines in making ductile titanium available2/ has resulted in the establishment of a new industry. Owing to its strategic importance and the combination of low density and high strength, titanium has received considerable attention as a structural metal. Titanium's favorable strength-to-weight ratio is of particular importance to the Army Ordnance for equipment that is transported by airplane or by foot soldiers.

Jan 1, 1956

By Nehemías López, Juan Escala, Nestor Deza, Antonio Bustamante

Desde el inicio de la operación minera en Antamina y a lo largo de los años, se han desarrollado e implementado tecnologías que han ayudado a optimizar los procesos de producción. Uno de los principales retos que se tenía, y en el que actualmente se está trabajando con más de una iniciativa, es reducir la dilución (material estéril enviado a la planta), pérdida (material con contenido metálico enviado a los botaderos de desmonte) y mezcla (representado por bloques de mineral de Cu enviado como CuZn y viceversa) de mineral en el proceso de carguío y acarreo.

Sep 30, 2022

Secondary blast holes are now being pierced in quartzite and sandstone quarries, using multiple hand-operated Jet-Piercing units supplied with oxygen, fuel and water from a compact mobile carrier. A unit of this type, operating in a Canadian quarry, enabled four Jet-Piercing blowpipes to pierce blast holes for two hours without shutdown. The piercing blowpipes used were developed by Linde Air Products Co., a division of Union Carbide and Carbon Corp. The mobile supply carrier was constructed by the quarry from specifications supplied by Linde and modified by the quarry operators for their particular use. Employment of the new self-contained unit, which allows up to four operators to pierce approximately 450 ft of blast hole without shutdown, accelerates rock removal operations. Normally, only two blowpipes are in operation at one time. Large boulders or ledges, which sometimes remain after primary blasting to hamper loading operations, can, in the case of certain hard rock, be prepared for reduction more rapidly with these new units than by any other means. A special feature of the new manual Jet-Piercing unit is the mobile gas and fluid supply carrier. It consists of a standard truck chassis fitted out with four banks of large standard-capacity oxygen cylinders, a steel-holding tank for fuel oil, and a gasoline-driven air compressor and tank for pressurizing the fuel oil tank. Cooling water for the blowpipes is supplied to the unit from a hose extension to the quarry supply line. Feeder lines from the oxygen cylinder manifolds and the oil and water tanks terminate in four sets of take-off stations on the control panel at the rear of the truck. As many as four hand Jet-Piercing blowpipes can be connected to the take-off panel by high-pressure rubber hoses. The hand Jet-Piercing blowpipe used with the mobile supply carrier is a highly portable device which can be manipulated comfortably by one operator. The blowpipe can pierce blast holes at rates up to 60 ft per hour, depending on the properties of the rock. Blast holes can be pierced at any angle from the vertical to the horizontal, making it necessary for the operator to drill from the top of the boulder. Hole diameter is held to approximately that which allows the use of a standard 11/8-in. diameter dynamite. The manual Jet-Piercing blowpipe has these important design features: a burner from which the combustion gases emerge at supersonic speeds (in excess of 6000 ft per sec); a hole-sizing shell which controls the minimum size of the hole and protects the copper burner; and a sliding shield which protects the operator against the steam and spallings ejected from the hole during the piercing. The Jet piercing process has been applied successfully in United States and Canadian quarries within the last several years as an advanced method of "drilling" blast holes.

Jan 1, 1952

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By Caio Fernando Dias Guillen

Ao longo dos anos os aços para moldes plásticos tornam-se cada vez mais importantes no campo de aços ferramenta. A aplicação destes materiais estende-se pela indústria de processamento de diversos polímeros. Assim são esperadas propriedades específicas dos aços utilizados em cada condição: resistência mecânica, polibilidade, usinabilidade, resistência à corrosão e resposta à texturização são fatores determinantes na escolha do aço. O presente trabalho objetivou caracterizar, com relação às propriedades mais importantes para os moldes plásticos, uma gama selecionada de aços. Através de ensaios foi possível elaborar um quadro comparativo que define os aços que melhor respondem à determinada solicitação. A caracterização dos aços ocorreu através de ensaios de tenacidade, impacto, tração, dureza, características micorstruturais.

Jul 30, 2018

By J. -B. C. Varnier, J. A. Cremeens, D. D. Overton

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County in Colorado in the United States were investigated using three-dimensional discrete element modeling methods. Large-scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back-analysis was conducted using prefailure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. IntroductionThe Pikeview Quarry is an aggregate quarry located approximately 8 km (5 miles) northwest of Colorado Springs in El Paso County, CO, USA. The quarry has been operated by several owners since the early 1900s. According to the U.S. Mine Safety and Health Administration (MSHA, 1986), the quarry has been a major source of construction aggregate for the Colorado Springs area for many years. In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy.A large-scale slope failure occurred on Dec. 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on Sept. 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure.The objective of this paper is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry, and both of these mechanisms were given equal credence in the present study. Quarry excavation and backfilling was a key factor in the slope instability for both failure mechanisms. The excavation was backfilled in stages in an effort to provide slope support. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability."

Jan 3, 2018

MONDAY, FEB. 17 9.00 A.M. to 9.00 P.M. Registration at Institute Headquarters. 9.00 A.M. Meeting of Committee on Development of the Activities of the Institute, Room 905, 9th Floor. 10.00 A.M. Simultaneous Sessions of Institute of Metals Division, Room 2, 5th floor. Industrial Organization, Room 1, 5th Floor. 12.30 P.M. Luncheon at Headquarters, 5th Floor. 2.00 P.M. to 4.25 P.M. Simultaneous Sessions of Institute of Metals Division, Room 2, 5th Floor. Industrial Organization, Room 1, 5th Floor. Petroleum and Gas, Room 905, .9th Floor. 2.30 P.M. Sightseeing trip by automobile for the ladies. Among the points visited will be: The American Museum of Natural History. The Episcopal Cathedral of St. John the Devine. The Spanish Museum. The American Geographical Society. The American Numismatic Society. The visits will be followed by Tea. 4.30 P.M. Memorial Service to Dr. Rossiter W. Raymond, Auditorium. 8.30 P.M. Smoker, 5th.floor.

Jan 2, 1919

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By Aprígio Ângelo de Jesus

No presente trabalho, foram avaliados os efeitos do tratamento térmico de alívio de tensões na microestrutura e propriedades mecânicas de juntas soldadas dos aços SA516-70 e SA387-11 (ambos aplicados na fabricação de vasos de pressão). Chapas com 40 mm de espessura de ambos os aços foram soldadas por arco elétrico com arame tubular e, posteriormente, submetidas a tratamento térmico para alívio de tensões. A variação de dureza ao longo da solda e a resistência à tração dos materiais soldados e tratados termicamente foi avaliada. A microestrutura dos materiais soldados foi acompanhada por microscopia ótica convencional. Por meio do tratamento térmico empregado foi possível observar a redução do nível de encruamento nos metais base e zonas termicamente afetadas das juntas em ambos os materiais com aumento de ductilidade no aço SA516-70.

Aug 8, 2018

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975

By L. A. André Santos

Atmospheric processing of nickel lateritic ores with low costs has been encouraged. In this work the kinetic of atmospheric acid leaching of a northern- Brazilian ore with 1.63% Ni and large amount of fine particles (d50 ≈ 0.075 mm and 40% below 0.038 mm) is presented. Chemical analysis showed a trend of Ni and Fe concentration in finer fraction (−0.075 mm) and Si and Mg in the coarsest one (−0.500 + 0.150 mm) associated to distinct mineral phases. Nickel is widespread in the mineral matrix. Distinct behaviors were observed as a function of particle size associated to the distribution of silicates and iron oxides in the ore. The kinetic modeling indicated that leaching is controlled by porous layer diffusion at 65 °C, but at 95 °C exhibits a mixed control by porous layer diffusion in initial minutes (60 min) and by chemical reaction or diffusion through the pore layer in final minutes (60–240 min) depends on metal evaluated.

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

NEW YORK LOCAL SECTION Executive Committee LEWIS W. FRANCIS, Chairman WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. PHILIP A. MOSMAN, Treasurer Louis D. HUNTOON WILLIAM A. POMEROY The October meeting of the New York Local Section was held on Oct. 2 at 1424 Broadway, following a beefsteak supper, at which 71 members were present. B. B. Thayer spoke briefly on present labor conditions at Butte, A. A. Blow discussed labor conditions in New Zealand, and Hennen Jennings discussed the fundamental problems of industrial unrest. Several other members joined in the informal discussion which followed. The next meeting will be held on Nov. 7. THOMAS T. READ, Secretary.

Jan 11, 1914

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (>50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Rodrigo Rangel Porcaro

Desenvolveu-se um dispositivo para soldagem por gravidade com eletrodos revestidos e investigou-se o comportamento do dispositivo em função de variações nas condições operacionais. Ciclos térmicos durante a deposição de cordões em tubos de aço API X65Q foram avaliados por meio de medidas experimentais, utilizando-se termopares inseridos na poça de fusão durante a soldagem por gravidade. Amostras do metal base e do cordão depositado em diferentes condições de aporte térmico passaram por análise química, microestrutural e metalográfica. Observou-se boa repetibilidade na velocidade de deposição do dispositivo e aspecto visual adequado de cordões de solda depositados. Os resultados dos ciclos térmicos mostram que as variações nos valores de ?t800/500, utilizando eletrodos AWS E7018 e correntes de soldagem de 70A e 150A, causaram redução de 21% na proporção de ferrita acicular e, consequente, redução de 22% nos valores de microdureza do metal de solda com maior aporte térmico.

Oct 30, 2017

By R. T. Johansen, R. J. Heemstra

In water flooding the gradual accumulation of insoluble materials on the sand face causes the injection pressures to increase while decreasing the amount of water injected . This plugging material often is composed primarily of insoluble precipitates of calcium , iron , and magnesium . Treatment with sodium tripolyphosphate ( STP ) either eliminates or reduces the formation of precipitates . Field tests are discussed showing the almost immediate effects of using STP in the injection water . Methods of treatment , solubility of STP in fresh water and brines , and precautions to observe when starting to treat a waterflood with this chemical are given . Laboratory data show that the preferential wettability of a crude oil for reservoir rock can be reversed by adding a small amount of STP to the flooding water . This reversal in wetting tendency should not only decrease the injection pressures but also increase oil recovery by improving the sweep efficiency of a water flood .

Jan 1, 1964