Search Documents

By Leon J. Perrier

The paper describes the equipment in use, haulage grades, road conditions, tire sizes, tire performance and related problems. Various types of failures and causes, corrective action taken, tire records and reporting for control are also discussed.

Jan 1, 1977

By Lifeng Yang, Xiang Zhang, Liang Yuan, Yonghui Wang, Bing Hou, Mian Chen, Rixing Zhang

Large-scale hydraulic fracturing technique has been widely applied to the development of shale gas reservoirs, where the interaction between natural fractures and critical fracture zones has substantial impact on the propagation of hydraulic fractures. Therefore, it is of significant importance to understand and experimentally verify such mechanism. To reach this end, tri-axial fracturing tests were implemented on 400mm×400mm×400mm block samples collected from Longmaxi shale outcrops. The interplay between hydraulic and natural fractures was investigated during the tests, factoring in the role of pump rate in affecting the created fracture network. Based on the experimental results, the critical fracture zone, defined as the weak formation zone nearby the wellbore created by staged pressure implementation that is observed rapid fracture propagation upon next stage of pressure increase, was thoroughly investigated. The analysis illustrates that given the high brittleness of the shale formation, abundant critical fracture zones are generated around natural fractures with pressure building up at a relatively low pump rate. As the pump rate increases, hydraulic fractures initiate and come into play with critical fracture zones, implying emergence of a large number of micro-cracks. A changing pump rate modifies the way of interaction between hydraulic and natural fractures and the subsequent formation of fracture network. Long term fracturing fluid injection with relatively low pump rate below the activation of critical zones is suggested. Also proposed is appropriate timing when applying a specific pump rate that will contribute to the improvement of hydraulic fracture propagation.

Jan 1, 2015

By Bure R

Approximately 2.4 million ounces of gold and 11.3 million ounces of silver have been produced from the Umuna Lode by Misima Mines Pty Limited between June 1989 and the end of Decemeber 1996. Reserves remaining at the end of December were 32.1 million tonnes at 1.0 gram per tonne gold and 9.7 grams per tonne silver. To attain precious metal production of this volume, an estimated K60,000,000 (1996 Kina) was spent on exploration alone. from the 1940s to the present day. Exploration expenditure for the 1996 calendar year was approximately K4,400,000. With such a large investment in exploration, large quantities of data were generated and stored in various forms. To make best use of this data, it was necessary to organise and systematically store this data in a form compatible with a modern Geographical Information System (GIS). The Umuna Lode on Misima Island is a low sulphidation gold- silver deposit dated at 3.5 ¦ 0.2 Ma. The deposit is controlled by the 50 to 100 metre wide Umuna Fault- a moderate dipping, brecciated clay- chlorite- carbonate altered, normal fault zone. There is approximately 230 metres of mostly dip slip offset on this fault, which is measurable by the offset of the Cretaceous schist, marble and greenstone host sequence. Late Miocene microdiorite spatially related to the Umuna Lode does not appear to be genetically related to the gold- silver mineralisation. GIS was introduced to Misima at the end of 1995 and until recently has been mostly used for data storage and retrieval, the over- laying of various data sets to assist in targeting prospective areas, and as a drafting tool. The use of data-driven, predictive data analysis is the most recent effort in maximising the use of the extensive Misima database. By characterising the key controls and properties of the Umuna- type mineralisation, a Weights of Evidence, data-driven analysis produced a prospectivity map of Misima Island. The purpose of this map was to identify prospective areas yet to be explored and to assess the effectiveness of exploration to date.

Jan 1, 1997

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By M. Onifade, O. S. Otuogbai, A. F. Mulaba-Bafubiandi, O. D. Eniowo, H. Grobler

Artisanal and small-scale miners in Nigeria struggle to attract formal financing to upgrade their operations to a more sustainable form of small-scale mining operation. Literature shows that for an investment to attract formal sources of financing; the business must be considered creditworthy by potential lenders. This means that the credit risks associated with the investment must be bearable for the potential lender. This study looks at how artisanal and small-scale miners can attract formal funding, which will help them take the leap from artisanal state to a form of sustainable small-scale mining operation. This study evaluates the creditworthiness of artisanal and small-scale mining operators using key credit risk parameters identified in the literature and through primary investigation. A quantitative study is conducted on a sample of 100 artisanal and small-scale miner establishments in Nigeria to evaluate the effect of these identified credit risk parameters on creditworthiness. It is shown in this study that being a member of a mining cooperative society, which is a form of social collateral, best improves the chances of access to formal financing for miners within the sample group. This underpins the role of social collateral, in both the formal and informal economy, and its influence in improving the creditworthiness of a typical artisanal and small-scale miner.

Jul 23, 2025

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By Indresan Govender

A continuum based granular flow model of charge motion that combines the inherent frictional nature of particles with its distinctly fluid-like structure is presented. Starting with Newton?s 2nd Law on a volume element of charge, we derive the velocity field in the bed free-surface and the rising en-masse region. Invoking flux conservation within the two regimes of interest then yields a (simple) differential equation for the free-surface of the charge body. Combining the velocity field gradients with a suitable constitutive choice for the shear stress completes the picture with a description of the in-situ rate of shear power dissipation in a tumbling mill ? a mechanistically correct account of power draw in a tumbling mill. Positron Emission Particle Tracking (PEPT) was used to measure the in-situ flow fields of the charge within opaque systems like tumbling mills. The accurate velocity and mass distribution derived from PEPT form the basis for direct verification of the resulting granular flow models. In this regard a wide range of milling conditions is investigated and presented in this paper.

Sep 1, 2012

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

As the title indicates the central themes discussed in this contribution are sustainable development, information systems, and extractive industry. More specifically, the objective is to present a prototype for the systematic generation of extractive industry (henceforth: EI) û specific sustainability information. The paper begins with the authorÆs viewpoints on the core notions of sustainability, and development, as well as their relationship to information. These set the stage for the introduction of the information system (IS), as well as the follow-up sustainability information system (SIS) extractive industry sustainability information system (EISIS) concepts and related discussions. The paper continues with a second part, in which, efforts to research and develop an EISIS prototype are described. First, the team is presented. Second, the systemÆs aim and target groups are briefly discussed. After, an articulated overarching EISIS conceptual model emphasising capital accumulation, and service flow concepts û is presented. This is followed by a detailed description of the assembled prototype with a focus on data and information generation. The formulation of data generation, storage and transmission processes, as well as its use in sustainability interpretation rules and their embedment in the conceptual model is made with respect to monetised stock and flow parameters, measured in the appropriate dimensions. In the third part, the author presents and discusses the results of a first round of prototype experimental development in three major EI firms. First, the system observation, and data analysis protocols are described. Second, a review of protocol implementation, and respective results, is made. Finally, the overall performance of the proposed prototype, and development process issues are discussed, before suggesting areas for improvement and future research. The paper ends with a conclusion in which the author provides a retrospective balance of the æknowledge creation projectÆ, as well as a prospective outlook for research in this field; before acknowledgements are made and references provided.

Jan 1, 2009

By R. W. Leonardson

Tectonic activity in northern New Mexico during late Oligocene and early Miocene time presaged events which led to the development of molybdenite deposits at Questa. East-northeast directed crustal extension produced north-northwest striking tensional fracture systems paralleling the early Rio Grande rift. A sequence of Oligocene andesite flows and breccias is overlain by a thick early Miocene rhyolite ash-flow tuff. Eruption of the tuff initiated collapse of the Questa cauldron: the south margin of which occurs as an east-northeast striking, north-dipping structurally weak zone. Continued east-northeast post-cauldron extension permitted the high level emplacement of granite stocks with coeval rotational deformation of fault blocks composed of cauldron fill and [ ] floor. The stocks occupy north-northwest fracture zones in the south margin of the cauldron, and porphyry dikes occupy east- northeast striking faults that define the south margin. These two fracture systems have played a dominant role in localizing the intrusive porphyries and associated mineral deposits at Questa. A molybdenite-bearing breccia matrix and related stockwork mineralization generally occur within volcanic rocks. Mineral deposits are spatially related to fault zones and the upper con- tact of their source intrusives. Deposits are localized in fault zones up to several thousand feet long and 100 to 500 feet in diameter. Magmatic-hydrothermal solutions from the source aplite porphyries have produced potash metasomatic alteration which is strongly centered on the mineral and ore zones. Alteration in ore is represented by orthoclase, quartz and secondary biotite. This pattern grades into secondary biotite and propylitic zones forming successively weaker alteration assemblages away from ore. Younger phyllic and argillic assemblages are particularly widespread only where strong north-northwest extensional fracture zones cross the south cauldron margin.

Jan 1, 2013

By Yijun Cao, Shengpeng Su, Guihong Han, Xiangyu Song, Yanfang Huang

Binder is indispensable in the production of iron ore pellets and the quality of pellets seems to be related to the interactions between binders and iron minerals. Humic acid is proved a suitable binder for iron ore pelletizing. In this paper, the interactions between humic acid and iron minerals were investigated by adsorption experiments and molecular dynamic simulations. Adsorption experi- mentalresultsshowthattheadsorptionofhumicacidonhematiteiseasierthanthat on magnetite, and the maximum adsorption capacities of humic acid on hematite and magnetite reach 17.1, 7.39 mg/g, respectively. The results of adsorption iso- therms indicate that the Langmuir model provides the best correlation of the experimental data, while the thermodynamics results demonstrate that the adsorp- tion process is a spontaneous exothermic process. Molecular dynamic simulations reveal that the interaction between hematite and humic acid is stronger than that between humic acid and magnetite. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Xie Longshui

INTRODUCTION The gold production is from the state-owned gold mines, the local gold mines and the by-product of metal mines. Since 1975, the small gold mines have developed in rapid strides. Currently, there are about 3000 small gold mines in China. Most of them are operated by the local, and the production is about 50% of China's gold output. In the small gold mines, the normalized mining equipments are employed at most of mines, but some mines still use such backward tunnelling and mining tools as pick, shovel and hand hammer etc.. The mining techniques have developed from the primitive to the advanced, especially the methods of open stope, shrinkage and filling have been widely used. Such new mining techniques as bolting, vibrating draw, non-electric ignition and diamond drilling etc. are also introduced in the wall gold mines. In recent years, the development of small gold mines is very fast under the guidance of new mining policy which is ' rapid and great development of large-sized mines, helping small mines to develop, and quick mining for the existing mines; and encouraging the collective and the individual to operate a mine.' GEOLOGICAL FEATURES The gold veins are dominant, which are divided into two types, ie. the mesothermal deposit with altered rock in a crushed zone and the hypothermal deposit with quartz veins. The orebody distribution is not centralized, and the size of deposit and single minable orebody is small respectively. Most of deposit dip at 30° to 50°, characterized by expansion and shrinkage, ramification and compound, thinning out and reappearance, separation and composite at the parallel veins etc.. The ore grade is variable, and the factor of grade change is above 100%. The waste zones with lean or submarginal ore usually exist in deposits. As for the gold deposits with altered rock, the ore boundary is indistinct. Most of gold deposits, particularly the gold deposits with altered rock, are intruded by the late structural rock, thus the faults and joints are developed, and the rock and ore are crushed, especially the host rock of roof wall is very crushed. It ie obvious that the conditions of both formation of deposit and mining are considerably complicated. HISTORY With a long mining history and rich experiences, the local gold sectors are small, but they play an important role in China's gold mining industry. Dated from Xia and Shang Dynasty, the gold goods was made. In the Tang Dynasty, the development of gold mining industry was very fast. A Chinese poem , written by Liu Yuxi -- one of famous poets in the Tang Dynasty, says: As sun is shining over Dengzhou land, The fog on river slowly goes away, The panning girls together meet at bay, The beauty's jewels and stamps of king are gold from river sand. This poem shows the local gold mining was flourishing at that time. In 1888, the local gold mining sectors were all the rage at the moment, and the annual output of gold was as high as 21.5 tons. Since the founding of New China, the development of local gold mining was subjected to several back- sets, but certain advances are made on the whole, especially since 1970. Round about 1970,the simple, backward and indigenous mining was dominant in the small gold mines; for instance, the hand-hammer drilling, the hand-operated winch hoisting and the hand haulage etc.were main methods of gold mining . Up until the late 1970s,great changes took place in stoping, haulage and so on. Currently, some advanced technology and large-sized equipments are adopted in the local gold mines. Generally, the local small gold mining sectors play an important role in development of China's gold mining industry, and are important and attractive sectors. PRESENT DEVELOPMENT

Jan 1, 1987

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957

By Wayne Hilgedick

Peabody Coal Company is the nation's largest producer of coal and is headquartered in St. Louis, Missouri. In 1978 Peabody divisionalized its operations to establish more responsive and effective mine management. Peabody Coal Company's Arizona Division operates two large surface mines, the Black Mesa and Kayenta Mines. Both are located in northeastern Arizona, approximately 30 miles from Kayenta, Arizona, on the Navajo and Hopi Indian Reservations. The Black Mesa Mine produces 4 to 5 million tons of coal per year and the Kayenta Mine produces 7 to 8 million tons per year. Coal from the Black Mesa Mine is transported 274 miles by coal slurry pipeline to the Mohave Generating Plant located on the Nevada/Arizona border at Bullhead City, Arizona. This plant is jointly owned by Southern California Edison, the Los Angeles Department of Water and Power, Nevada Power Company and Salt River Project Agriculture Improvement and Power District.

Jan 1, 1983

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976