Search Documents

The role of a project metallurgist is diverse and covers input into the resource definition, mining studies, metallurgical test program development, process engineering and plant design, cost estimate preparation and financial analysis aspects of project feasibility studies. Mining project schedule and cost overruns can often be attributed to cutting short metallurgical test work, engineering and cost estimating leading up to commitment to development. In a significant number of cases this may result from the lack of understanding and commitment by the project proponent to the requisite metallurgical and processing studies required during the various pre-commitment stages of a mining project. Metallurgical test work, process development, engineering and cost estimating requirements for each stage of pre-commitment development are described together with a summary of the ongoing role of the project metallurgist during detailed engineering and commissioning of a process plant.

Jan 1, 2008

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By I. J. Kotzé, R. T. Jones

Conventional PGM matte smelting requires the presence of a certain quantity of base metal sulphides in order to collect the platinum group metals in a molten sulphidic matte phase in the furnace. Furthermore, the quantity of chromium oxide in the feed materials is controlled in order to avoid the build-up of high-melting chromite spinels in the furnace. Mintek has developed a process for smelting difficult PGM-containing feed materials that contain low amounts of sulphur and/or high amounts of chromium oxide. A DC arc furnace is used to provide the appropriate conditions to generate an iron alloy that collects PGMs very effectively, leaving extremely low residual quantities of PGMs in the slag. Various feed materials have been treated successfully in furnace campaigns running at power levels up to 1.5 MW. The longest of these campaigns was run continuously for more than four months, treating more than two thousand tons of materials such as low-grade concentrates, revert tailings, and converter slag. The campaigns demonstrated the robustness and versatility of the process, and proved that it is possible to sustainably produce a PGM-containing alloy and discardable slags containing an average of less than 1.4 g/t of PGMs over the entire campaign. Keywords: DC arc, smelting, furnace, platinum, PGM, revert tailings, converter slag, ConRoast

Jan 1, 2004

By Wenxue Chen

This paper presents a new type of bolt with full thread and uniform strength, and fabricated with a Glass Fiber Reinforced Polymer (GFRP) bolt-making machine designed by the authors. The mechanical performance of the new bolt is assessed with strength tests conducted with the bolt in acid, alkaline and saline water conditions, with increasing concentration. The purpose is to test the new GFRP bolt?s mechanical performance in harsh conditions, especially metal mines with acid or alkaline environments. Comparison of the color, weight, size and antistatic ability of the GFRP bolt before and after it is immersion in solution is presented. Changes in tensile and shear strength, torsion, and anchoring force were evaluated in the laboratory. The results show that the mechanical properties of the GFRP bolt are more sensitive in alkaline than in acid and saline water. However, the loss ratio of mechanical properties of the GFRP bolt is very small according to the results of tensile and shear strength, torsion and anchoring force. The new bolt can be useful for applications in acid or other harsh mines.

Aug 1, 2013

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

"IntroductionIn the 1970s, environmental concerns and associated liabilities were a new and unknown aspect of corporate risk. Today, social concerns and the associated conflicts that they can generate constitute a rapidly expanding aspect of risk. Although not a new phenomena — the Bougainville copper mine was forced into closure in 1988 — social risk has emerged as considerably more important, and increasingly visible, in the last few years. Social risk is now an aspect of all mining activities which needs to be calculated into project assessments, and to be managed throughout the life of a project. While social risk has a number of aspects at the corporate level, such as company image and shareholder relations, at the level of the individual project, its primary component is social acceptability, and the principal tool for managing it is the Social Licence to Operate.Social Risk in Latin AmericaThroughout Latin America there are newly modernized mineral codes and economic systems introduced over the last ten years which, together with new environmental legislation, look very much like regulations in developed countries. To the corporations, the existence of these instruments means that the risks from the environmental issues associated with the project are known; they are legislated, defined, quantifiable and hence manageable.It seems ironic that, just when comprehensive regulations for the environmental management of mining have been put in place throughout Latin America, there arise an increasing number of challenges to mining activities. For, in spite of the apparent guarantees provided by these new legislative reforms, communities in Latin America today are more frequently standing up and taking exception to the presence of mining companies, or the ways in which the companies are conducting themselves. The viability of projects becomes threatened because they are considered socially unacceptable, a phenomenon that we describe as social risk. These challenges are less about opposing mining activities than many people would think. Rather, they are based on an increasing desire on the part of the local population to have some measure of control over their own future, and to participate in the development process from the earliest stages."

Jan 1, 2000

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012