Search Documents

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By C. M. Mason

The methods currently used by the Bureau of Mines to evaluate the sensitivity, strength, incendivity, gaseous products, and physical properties of explosives and hazardous chemicals are described. Included are the tests used to evaluate explosives which arc certified as permissible for use in underground coal mines.

Jan 1, 1972

By B. H. Caudle, A. D. PUCKETT

This paper summarizes precent knowledge of the ignition qualities of pure hydrocarbons likely to be present in modern Diesel engine fuels, as shown by an extensive search of the technical literature. The report also discusses the possible significance of cetane number and hydrocarbon struc- ture. Cetane or cetene numbers, and other physical properties, are tabu- lated for about 100 hydrocarbons, and a bibliography is appended. In recent years the Diesel engine has enjoyed increasing popularity due to its dependability, inherent characteristics of fuel economy, and the fact that it operates on a fuel that hitherto has been available in comparatively large quantities at a low price. These qualities have en- abled the compression-ignition engine to compete very favorably with other types of prime movers in many fields and have led to predictions of fur- ther rapid expansion in the application of Diesel power. In a survey of the field of all petroleum fuels for combustion engines, Holaday et al (9) have predicted that by 1948 railroads will be using 10 times as much Diesel fuel as was used in 1939 and that over-all consumption will have doubled that of 1939. Other estimates of the yearly demand for Diesel fuels five years hence vary from 2,6 to 5 times the amount used in 1944. Into this picture has come the question of whether the greatly in- creased production to meet this estimated demand is compatible with the maintenance and possible improvement in quality of fuels necessary to satisfy future engines. Unfortunately perhaps for the Diesel engine, factors other than those of simple arithmetical multiplication must be considered. For example, the consumption of oil in central heating plants doubled from 1935 to 1943, and a further increase of 57 percent of the 1943 demand is expected by 1950. Jet propulsion has been developed to the stage where it is entirely practical for military aircraft. Catalytic cracking plants, many of which were constructed to meet the war- time accelerated demand for high-octane gasoline, are taking their place in the refining industry. All these developments, as well as the Diesel engine, require material of approximately the same boiling range. Virgin gas oils make excellent burner fuels, perform most satisfactorily in the gas-turbine units for aircraft according to present information, and are at a premium as catalytic cracking stock.

Jul 1, 1948

By Aner W. Erickson

"Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.A preliminary examination was made by S. P. Holt, mining engineer of the Bureau of Mines, in company with John Reed, L. A. Warner, and W. S. Twenhofel of the Federal Geological Survey, on July 14, l943. Three samples were taken, rough estimates were made, and it was proposed that the area be mapped, topographically and geologically,. Dip-needle work was added to the program, and it was decided that, should results warrant, the deposits would be diamond-drilled.From March 26 to May 28, 1944, the deposits were examined thoroughly by Bureau of Mines personnel under the direction of the author. Thirty-two acres were mapped with contour intervals of 10 feet, grids were established covering the principal outcrops, over 1,500 dip-needle readings were secured, and the magnetite bodies were outlined. Additional information was gathered by trench inch and channel-sampling, 600 linear feet of trench being dug and 32 channel samples being cut. Finally, the mapped area was checked for nonoutcropping deposits by taking dip-needle readings at 10-foot intervals along the traverse lines, creeks, trails, and all outstanding topographical features. This re-connaissance work gave sufficient coverage of the 32 acres to eliminate the possibility of further magnetite bodies of any consequence remaining undiscovered.Acknowledgment is made to Nile Johannsen, assayer, Territorial Department of Mines, Ketchfkan, Alaska, for determination of samples.The deposits are on Prince of Wales Island in Southeastern Alaska near Tolstoi Pay, a deep-water indentation at the northwest and of Kasdan Peninsula. The physical features are shown on figures 1 and 2 and the location of the deposition figure 3. Old workings were found on the west side of Tolstoi Mountain; between elevations of 650 and 1,150 feet, at distances of 3/4 to 1-1/4 miles from the east shore of Tolstoi Bay.Access to the area is over a brushed foot trail built by the Bureau of Mines. Topography would permit construction of either surface or aerial tramways at moderate cost but would make road building expensive. Deep-water navigation, permitting inexpensive water transportation, is possible the year around.Kasaan Peninsula is an area of moderate relief, being considerably less rugged than the mainland to the east. Most of the mountains and ridges are less than 2,500 feet in height and show evidence of having been covered by the ice cap of the Pleistocene age. Rock exposures below elevations of 2,000 feet are limited, as extensive overburden 2 to 20 feet deep covers the greater part of the peninsula."

Dec 1, 1948

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By A. G. Starliper

The report covers studies by the Bureau of Mines on the removal of metallic values in two waste products from the Longhorn tin smelter at Texas City, Tex. One product was a slag that contained tin, tungsten, iron, tantalum, and columbium. The other product was a spent acid solution that contained tin, tungsten, iron, lead, copper, zinc, and silver and that came from presmelting treatment of impure tin concentrates. Molten slag was treated with sulfur or sulfur compounds and with coke, calcium carbide, or gaseous reductants to form tin sulfide that volatilized from the charge and to reduce tungsten along with iron and silicon to form a carbon-bearing metallic layer. The metallic layer was treated by an oxidizing alkali roast and then was water-leached to extract the tungsten. The waste acid was used in other experiments to dissolve an iron-tin- tungsten alloy (hardhead) obtained by direct reduction of the slag. An insoluble fraction containing tungsten, silver, silicon, columbium, and tantalum was removed, and copper was cemented on metallic iron, Tin was recovered by cementation on zinc plates, and lead was precipitated by adding sulfate ion. Iron was precipitated by increasing the pH which left a solution containing principally zinc. Slabs of hardhead were electrolyzed in an electrolyte consisting of waste acid to plate out groups of metals at different pH?s. The time did not permit thorough exploration of this method of treatment.

Jan 1, 1962

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By L. Ntlhakana, K. Khoza-Shangase, G. Nelson, I. Maposa

Occupational noise-induced hearing loss (ONIHL) is associated with various risk factors in South African mines. We investigated the association between standard threshold shifts (STSs) and exposure to noise and platinum mine dust (PMD), using demographic data, five years of annual audiometry screening results, and noise and dust exposure data. Miners’ age, sex, percentage hearing loss (PLH), and dust and noise exposure data were gathered, and a linear mixed effects regression model used to predict STS. Average occupational exposure levels to noise and dust were calculated from recorded measurements. A total of 12 692 records were analysed. Most miners were male (89.6%) and more than 50% were younger than 41 years. More than 70% were exposed to > 85 dBA noise and 58% were exposed to 1.5–2.99 mg/m3 PMD. Changes in hearing levels ranged from 8.3 dBHL at baseline (2014/2015) to 10 dBHL in 2016 (STS), with no changes thereafter. The model showed that the estimated effect on STS for males was 27% and 21% higher than for females, for the left and right ear, respectively The estimated effect of age, PLH, noise exposure and years of exposure on STS was < 10% for each variable. There was no statistically significant association between PMD and STS. The combined effects of age, sex, years of exposure to noise, and noise exposure levels, and strength of associations can be used to predict STS for this group of miners. Our findings may be used to measure the efficacy of the mine’s hearing conservation programme.

Aug 1, 2021

By Verônica Scarpini Candido

O alto consumo de energia e a elevada emissão de dióxido de carbono são os maiores problemas da indústria de cimento Portland relacionados à poluição do meio ambiente. Com o objetivo de reduzir estes problemas, os cimentos geopoliméricos despontam como uma nova classe de materiais de alto desempenho e não agressivos ao meio ambiente utilizados como aglomerante mineral capaz de substituir total ou parcialmente o cimento Portland. Estes cimentos são considerados quasi-frágeis devido ao seu comportamento elástico não-linear, provocado pela relaxação e redistribuição de tensões antes da ruptura. Todos os resultados obtidos no programa experimental para o concreto de cimento geopolimérico (CCG) foram comparados com aqueles obtidos para o concreto de cimento Portland (CCP), sob as mesmas condições de ensaio. Neste trabalho, são apresentados resultados de difração de raios-X (DRX), microscopia eletrônica de varredura (MEV) e análise térmica (DSC/TGA), a fim de reunir informações para um melhor entendimento da microestrutura do concreto geopolimérico.

Oct 30, 2017

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and mediumterm activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter, and ventilation constraints in order to create more realistic schedules and enhance miners’ health and safety.

Sep 6, 2023

By W. Krieglstein

Due to the natural variability of ores, it is necessary to carefully test flotation behavior of flotation cells before designing flotation circuits. For performing quick and versatile tests in the laboratory, Siemens developed a laboratory-size Hybrid Flotation Cell, which has been down-scaled from the 300 m³/h production cell to a 0.6 m³/h flotation cell. This small cell is being used as a test bed for technical and chemical concepts, the improvement of decisive components and the characterization of customer ores. In this study the evaluation results for Andean porphyry copper ores are shown. Total recovery rates of the order of 45 to 50 % have routinely been achieved in a single flotation cycle over a wide range of feed grades. In addition, the Hybrid Flotation Cell has proven to be particularly well suited for the flotation of fine particles below 20 µm down to below 1 µm, at high recovery rates and concentrate grades.

Sep 1, 2012

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940