Search Documents

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By Alfredo Valencia-Toledo

This study delves into the satisfaction levels of indigenous communities in Apurimac-Cusco, Peru, concerning mining activities in their region. Our primary objective is to elucidate the interrelationships among observable variables, which are conceived as linear combinations of multiple factors. Employing the statistical methodology of exploratory factor analysis, we aim to pinpoint the pivotal factors influencing the progress of mining activities in Apurimac-Cusco. Through our analysis, we have identified eight key factors that exert a significant impact on mining’s sustainable development in the area. These factors encompass diverse facets, ranging from the support offered by mining company to communities, environmental considerations, education, economic factors, provision of basic services, transportation and communication, support for social organizations, and social-health-related aspects. This research endeavors to provide a comprehensive understanding of the complex dynamics surrounding mining activity satisfaction among the indigenous population, offering a basis for further exploration and policy development.

Feb 17, 2024

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Oliver Bowles

The various Latin American countries are undergoing a slow process of industrialization. The harvesting of one or two agricultural commodities or the mining of a few marketable minerals is being supplemented by development of an Integrated industrial economy. In many countries, progress in this direction has not been rapid, but as it gains impetus an increasing market for cement is a natural consequence. This is evident from the fact that industrialization is linked with increasing transportation, and means of transportation are very poor in much of Latin America. Bridges, culverts, and concrete Highway&apos;s, now scattered sparingly throughout the vast land areas south of the United States, must multiply as the demands of industry increase and as a higher scale of living is attained. Eventually the South American countries will be linked by modern highways. Furthermore, the arid climate of many regions creates a demand for construction of dams and irrigation works, and a continent poor in coal reserves but with abundant water power inevitably must direct its energies toward the construction of hydroelectric power plants. Countries rich in raw materials but with few natural harbors have urgent need of massive concrete breakwaters and docks. The demand for concrete in houses will also grow. Standards of living are low, and perishable building materials are widely used. As living conditions improve cement will be used increasingly in home construction. Even in the field of simple and modest housing cement affords a means of creating low-priced verminproof and fireproof homes, for which the need it imperative under climatic conditions that prevail in this area of the world. Already many of the countries have undertaken extensive public works, and such programs are likely to increase. Assuming moderate industrial progress and stabilized governments the demand for cement in this great southern area promises substantial growth.

Jan 1, 1940

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962

By H. T. Kennedy

The fact that intrusion of water into oil wells can be prevented by treating the sand adjacent to the well seems to have been only recently recognized. Swan1 mentions the process of solidifying naphthalene in strata. R. Van A. Mills2 recommends the use of materials such as sodium silicate and sodium carbonate, which react with oil-field water to form solid plugging agents. When a well is drilled in a new field the oil sands are found essentially devoid of water (Fig. 1). Unless a completely impermeable break exists over wide areas in the field, no water is found above the lower limit of the oil zone and no oil is found below the upper limit of the water zone. After considerable oil has been taken from the well, however, it is almost universal experience that water intrusion occurs. This intrusion may be of two kinds. The water may follow a path parallel to the bedding planes of the producing formation through loose streaks in the pay sand, as shown in Fig. 2, or the water level of the field may rise and enter the well by coning (Fig. 3). Water entering from the side is called "edge water," and that coming in from the bottom is called "bottom water.&apos;&apos; Effectiveness of any method for shutting off water depends not only on the effective treatment of the sand adjacent to the well but on

Jan 1, 1936

By H. T. Kennedy

The fact that intrusion of water into oil wells can be prevented by treating the sand adjacent to the well seems to have been only recently recognized. Swan1 mentions the process of solidifying naphthalene in strata. R. Van A. Mills2 recommends the use of materials such as sodium silicate and sodium carbonate, which react with oil-field water to form solid plugging agents. When a well is drilled in a new field the oil sands are found essentially devoid of water (Fig. 1). Unless a completely impermeable break exists over wide areas in the field, no water is found above the lower limit of the oil zone and no oil is found below the upper limit of the water zone. After considerable oil has been taken from the well, however, it is almost universal experience that water intrusion occurs. This intrusion may be of two kinds. The water may follow a path parallel to the bedding planes of the producing formation through loose streaks in the pay sand, as shown in Fig. 2, or the water level of the field may rise and enter the well by coning (Fig. 3). Water entering from the side is called "edge water," and that coming in from the bottom is called "bottom water.&apos;&apos; Effectiveness of any method for shutting off water depends not only on the effective treatment of the sand adjacent to the well but on

Jan 1, 1936

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, &apos;750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By H. J. McQueen

Mineral and energy resource consumption were continuously reduced by process improvements as chemical understanding was developed and applied. During the past two centuries, technological improvements increased human productivity that was accompanied by social advances and labour saving products; however, these sometimes proliferated to endanger sustainability, e.g., automobiles. In the steel industry, precisely controlled rolling of HSLA steels required little extra mineral consumption but reduced weight and heat-treating energy. Continuous casting of slabs reduced scrap compared to ingots and energy for the homogenizing soaking pit. Al alloy extrusions were improved by retaining the strengthening in the near-surface substructure, of high strength textures and of press quenching that is suitable for direct age hardening. Continuous bar casting of Al-0.65Fe, coupled with rod rolling and followed by wire drawing with only a final recovery anneal, yielded electrical wiring for households to replace less plentiful Cu and later for light-weighting use in autos and aircraft Looking backwards, the 1970 decade saw the first oil crisis and inspired Ottawa to undertake a campaign to develop an energy strategy that would decrease dependence on imported fuels. One significant undertaking under Energy Mines and Resources was the organization of industrial energy conservation, managed by each industry association,that collected detailed current statistics and set the goals for a 2-year campaign. The metal producing industries, as compared by E.C.N. Perryman to about 7.2 exajoules (EJ) for the nation, consumed about 0.8 EJ, being about one third of all heavy industries. While manufacturing consumed 30.2% of total energy, it created 87.3% of total national dollar value. Within the industrial envelope, smelting and refining utilized 28% (0.67 EJ, mining beneficiation 6.7%, 0.16 EJ); there was a significant contribution to exports: 80% of iron ore and 70% of aluminium in 1973. A general concern was that decreases in ore grade would lead to a rise in energy expenditures countering benefits from processing efficiency.

Jan 1, 2012

By H. V. Fairbanks

It is estimated that millions of tons of coal fines are unsaleable each year due to difficulty of drying them economically with conventional mechanical dewatering and thermal drying equipment. The difficulty is due to the fact that coal of small particle size presents a large surface area with polar groups which have a great affinity for water. In order to remove this water thermally, a high temperature is necessary which oxidizes the surface of the coal. This substantially reduces the heating value of the coal. If drying could be satisfactorily carried out at a lower temperature, much more of the heating value of the coal fines could be retained. It was conjectured that acoustic energy applied during the drying process might prove to be of value since acoustic energy has the property of producing cavitation at a liquid-solid interface when the intensity is sufficiently great. This cavitation process produces water at room temperature which can be carried away from the solid surface by a flow of relatively cool air. Hence, moisture removal is made possible at a lower temperature.

Jan 1, 1966

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau&apos;s work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price &apos;tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

By Walter McKee

WHEN mixed with common cast steel in quantities ranging from 11 to 13 ½ per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time. Manganese steel has been manufactured for about 26 years. .It was first made in a small way in England and subsequently produced in the United States in 1892. At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 lb. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13 ½ per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 5 ½ in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 5 ½ in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an

Jan 12, 1915

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ No reports were made on motor gasolines Bold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 6/The present report presents analytical data for 1,499 samples, representing the products of approximately 105 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gaso¬line are not considered adequate to represent this type of motor fuel, data for these analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows; Regular-price, 872 samples, 266 items, and 83 brands; -premium-price, 584 samples, 217 items, and 72 brands; third-grade, 43 samples, 32 items, and 21 brands. The meanings of those terms as used in the surveys are as follows:"

Jun 1, 1945