Search Documents

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpre-tation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By Lincoln Silva Gomes

Processos metalúrgicos durante soldagem provocam tensões residuais em peças soldadas. Recentemente foi observado um efeito de redistribuição das tensões residuais de soldagem num período de até duas semanas após o termino do processo de soldagem. Existe hipótese nossa que esta redistribuição das tensões está associada a mudança na microestrutura que ocorre no material após do processo de soldagem. Para provar esta hipótese, uma simulação física dos ciclos térmicos do processo de soldagem foi realizada utilizando a simulação física termo-mecânica (GLEEBLE). Através da técnica de microscopia eletrônica de varredura associada a técnica de difração de elétrons retroespalhados (MEV–EBSD) foi observada a variação da misorientação dos grãos e mudanças na microestrutura do material nos primeiros dias após soldagem, acompanhada de redistribuição das tensões residuais.

Aug 17, 2017

By R. A. Beall, S. L. Ausmus

The development of a completely water - free expendable graphite mold material , useful for reactive metal castings , has been detailed . Mixing and curing variables have been evaluated both by physical testing of the material itself and by castings of titanium , zirconium , and hafnium . The blend of powdered graphite , cornstarch , dextrin , cereal binder , linseed oil , and Carbowax -4000 is a successful mix when mulled in a carbon dioxide atmosphere , and properly cured and fired . The primary advantage of this material is its adaptability to standard foundry techniques ; i . e . , core blowing and hand ramming . Temperatures in the curing and firing cycles do not exceed 960 ° C , and no vacuum firing is required .

Jan 1, 1964

By Irwin H. Cornell

BRIEFLY stated, the history of the St. Joseph Lead Co. is the story of how a group of men, working for ten years as officers without salaries and stockholders without dividends, developed a small mine in Missouri into what became a large and prosperous corporation. Their courage and faith in the scattered surface deposits of lead coupled with the management's engineering vision and sound financial judgment should prove an inspiration to present-day mining operators and investors. In 1717, John Law's company, known as "The Company of the West," was formed in France and letters patent were granted, for a period of 25 years by Louis XV, for exploration in the Mississippi River Valley. One of the underlying purposes of the expedition, headed by Mr. Renault and Mr. La Motte, a French metallurgist, was development of the lead mines in the area now known as Southeast Missouri.

Jan 1, 1947

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017

By M. Kozlowski, I. Candy, S. Kashani-Nejad

The production of ferronickel and matte from nickel laterite ores is dominated by the Rotary Kiln, Electric Furnace (RKEF) process. Over time, major improvements have been made to kiln operation. In particular, kilns are now required to perform substantial amounts of reduction of the metallic oxides, thereby reducing the load on the electric furnace and substituting less expensive fossil fuel for electrical energy. To the basic refractory lined cylinder have been added: internal features such as dams and lifters, aimed at changing residence times in different sections of the kiln and enhancing gas/solids interaction, on-board fans to introduce tertiary air and on-board scoop mechanisms to allow reductant coal additions to be made at advantageous locations along the kiln. Many of these advances in design have been made on a trial and error basis and by 'borrowing' technology from related kiln processes, supplemented by proprietary modeling to various levels of sophistication. This paper presents a conceptual review of modeling components for the development of a computational model for granular material flow, combustion and heat and mass transfer in a nickel laterite kiln. These components include: granular material flow and segregation models for the simulation of bed motion, heat transfer models that simulate heat transfer by turbulent diffusion and radiation and the distribution of this thermal energy within the bed, and fluid flow models for the prediction of combustion aerodynamics.

Jan 1, 2005

By J. Bruce Clemmer

[Gypsum is one of the most important nonmetallic c minerals, as is indicated by the fact that the United States consumed approximately 3,500,000 tons of natural and calcined gypsum in 1937. The building trades were the largest users required 2,520,000 tons of calcine for production of plaster, wall board, tiles, block, and various other insulating and building materials. The glass and ceramic industries and other manufacturers required an additional 126,000 tons. The balance was used in the uncalcined condition as retarder in Portland cement and or agricultural purposes.]

Jan 1, 1941

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By C. V. Deutsch, D. A. Silva

The geologic modeling of multiple domains is required for the prediction of mineral resources and reserves. In general, explicit methods have wide acceptance among modelers due to the ability to manually add deemed important trends and geological features into the models. As an alternative, implicit geologic modeling techniques are increasingly adopted to reduce professional time requirements. These methods aim for objective, repeatable and flexible models by replacing the manual time-consuming interpretation of sections with the interpolation of signed distance values. These techniques, however, have been developed for the binary case of two domains at a time. The current paper presents an algorithm that extends the binary case to multiple domains. The method is able to transfer large-scale geological features from data to geologic models. A case study illustrates the benefits of the algorithm and practical implementation considerations.

Jan 1, 2016

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, 226 active mines and mills were registered in New Mexico and included four coal, eight potash, 11 metal, 33 industrial mineral and 170 aggregate and stone operations. New Mexico leads U.S. domestic production of potash, perlite, zeolite and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica and decorative stone. New Mexico also has the potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REEs), niobium and zircon, and other REE deposits are being explored. REE-thoriumuranium veins have been found in the Gallinas, Capitan and Cornudas Mountains and Laughlin Peak-Chico Hills. Exploration for beryllium has occurred in the Ojo Caliente No. 2, Cuchillo Negro and Victorio mining districts. Companies also are examining high-calcium limestone and high-magnesium dolomite for potential development, while aggregate continues to be important in urban areas and along highways. IntroductionIndustrial minerals and rocks are literally the building blocks of our way of life. They are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics to refractories to paper. Although industrial minerals permeate nearly every aspect of daily life, their presence and their roles are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the nonmetallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a byproduct of cleaning natural gas, one of the world’s major energy fuels.Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 41 percent of the more than $3.1 billion generated by mineral production in New Mexico in 2014 (Table 1). In 2014, 226 active mines and mills were registered in New Mexico and included four coal, eight potash, 11 metal, 33 industrial mineral and 170 aggregate and stone operations (New Mexico Mining and Minerals Division, 2015a). New Mexico leads U.S. domestic production in potash, perlite, zeolite and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica and decorative stone. Additional production statistics can be found in Harben et al. (2008). Major industrial mineral districts are shown in Fig. 1."

Jan 6, 2017

By Gary A. Kingston

This examination of Pacific Northwest (Idaho, Montana, Oregon, and Washington) ferrous scrap-industry operations, principally those in Oregon and Washington, points out factors influencing the supply and consumption of scrap materials, such as the complete dependence of steel ingot producers in these States on scrap as a metal raw material and the sizable quantity of scrap exported from Seattle and Portland to Japan. The pattern of the industry is presented as a movement of materials from their diverse sources to the consuming market. The geographic locations of the consuming industries in relation to the areas generating scrap materials and the movement pattern of the supply from source to destination strongly influences the cost of the commodity. The best measure of the scrap supply available in an area is experience in terms of how much scrap was withdrawn at a given price. Scrap availability is not finite, because the return of materials as scrap is secular and influenced by constantly varying market conditions. Steel ingot producers use 75 percent of the approximate 500,000 tons of scrap consumed in Oregon and Washington; steel foundries take 15 percent of the total; and iron foundries, ferroalloy plants, and other miscellaneous consumers utilize the remainder. Also, from 1955 to 1960 an average of about 200,000 tons has been exported annually from Oregon and Washington. The foreign exports are supplemented by lesser shipments to other steel producing States, principally in the western United States. From 1955 to 1960 the preferred and higher value heavy melting scrap grades accounted for about 60 percent of total withdrawals which varied between 600,000 and 950,000 tons annually. Total crap withdrawals from Oregon and Washington are projected to 1.8 million tons by 1985, 60 percent (1.1 million tons) of which will be heavy melting grades. No. 1 heavy melting scrap is most attractive to scrap consumers at $35 per ton or less. Price-supply relationships compared with projected scrap requirements indicate future prices possibly over $35 per ton. High prices over a long period could motivate the Pacific Northwest scrap consumers to produce steel from iron ore. However, technologic changes taking place at integrated steel plants could reduce scrap withdrawals from the Pacific Northwest, which might keep the scrap price sufficiently attractive to obviate production of competitive iron products by the Pacific Northwest scrap consumers.

Jan 1, 1964

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971