Search Documents

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By B. Singh

The use of wire ropes has already been tried in a few countries for roof support In mines. But the use of scrap wire ropes, as a method of support on extensive scale has not been reported from anywhere except India. Extensive trials using freshly discarded wire ropes for roof support were undertaken both in the laboratory and field. In laboratory, model beams supported with different reinforcing techniques were tested to evaluate their comparative load bearing capacity vis-a-vis reinforcing factor. Among all the tests, the model supported with wire rope system at 60° angle in combination with two supplementary vertical bolts offered the best result 1.e. about 95% reinforcement. It also accepted post fracture loading of the beam. In statical analysis too, the best result could be obtained with the rope installed across the gallery at 60° angle. All these findings are in conformity with the field observations obtained during roof stitching practices in coal mines. Of late, roof stitching, an effective and economical method of roof support developed at CMRS, India in 1972, found wide application in over 200 coal mines. In this method, a freshly discarded wire rope is grouted across a gallery in two inclined drill holes supplemented with two middle vertical roof bolts at every 1.0 to 1.2 m interval along the gallery. It is tensioned against the roof using wooden sleepers and thus, the whole system functions like a roof truss.

Jan 1, 1990

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

The statistical nature of the variability in detonation times of pyrotechnic delays is discussed, and how to evaluate the probability of required detonation intervals is shown. Some methods (analytical and stochastic) are given for designing blasts to ensure that any adverse effects on the variability in the delays is taken into account and minimised. Using computer models of blasts, detonation simulations can be used to check the initiation sequence for the probability of sequence reversals, indicating areas of high blast damage potential. Charge consumption rates, which relate directly to the resulting vibration levels, can be examined for their susceptibility to variation from delay variability. Models that synthesize vibration waveforms for production blasts, when taking delay variability into account, indicate the difficulty in vibration level prediction.

Jan 1, 1992

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to, uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month.

Jan 2, 1927

By A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

Strengthening a mine with the Power of their Employees: ?Imagine if the global economy collapses, your head office calls, and tells you to shut down for 3 months... now what do you do? ? HVC Business Improvement Initiative Why did we need help ? External Events ? How we responded ? How we worked with Westwind ? Alignment ? Priorities ? Coaching ? Focus Groups ? Innovation ? What worked / Opportunities ? Questions

Nov 1, 2011

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By Sans H

The geostatistical Discrete Gaussian (DG) model is demonstrated to be capable of providing an effective means of implementing change of support for Enterprise-style mineralisation and thus providing reliable global recoverable resource estimates. At Enterprise, sample grade distribution proves to be highly positively skewed, therefore significant deskewing of the histogram and reduction of variance occurs when going from sample to block support. The DG model was experimentally tested in&apos;the Southern Primary Zone (SPZ) at Enterprise, where high anisotropy ratios and pronounced short range structures are observed in variograms. The experimental test was run for a change of support for which the variance reduction was. approximately 60 per cent. This reduction is similar to that predicted by Krige&apos;s Relationship (&apos;the volume-variance relationship&apos;) for the practical situation of a change of support from 5 m vertical blasthole samples to 3 m x 8 m x 5 m selective mining unit (SMU) blocks. The DG model was found to correctly predict the grade tonnage relationships for a wide range of cut off grades. The experimental test indicated that, given a representative histogram and variogram, the DG change of support provides a computationally efficient and practical means of reliably assessing global mineable resources at the early stages of a mining project. Further, it allows a range of selectivity strategies to be meaningfully and comparatively considered prior to mining.

Jan 1, 1995

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.&apos; The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By Harry C. Gatos, Frank J. Bachner, Mario D. Banus

The portion of the Nb-Sn phase diagram between 75 and 79 at. pct Nb at temperatures near the liquidus has been investigated by melting alloys of known composition and examining the microstmc-tzlres resulting when these melts were quenched. The Nb-Sn samples were contained in magnesia sleeves, and were mounted in a high-pressure apparatus. It was shown that Nb3Sn me1ts by a peri-tectic decomposition and that the composition of the compound Nb3Sn at the peritectic horizontal lies between 77 and 78 at. pct Nb. Analysis of the phases present in the samples was accomplished by anodic staining techniques and an electron-microbeam analyzer. DURING the past several years a great deal of work has been devoted to the Nb-Sn system, and the bulk of this work has been primarily concerned with the intermetallic phase Nb3Sn. However, the melting characteristics of Nb3Sn have not been investigated because of the difficulty in maintaining known compositions due to tin losses by vaporization, and the added difficulty of containing Nb-Sn alloys without sample-container reaction at the high temperatures involved. This paper reports on the development of a technique for containing Nb-Sn alloys under pressure high enough to prevent tin losses at temperatures in excess of the liquidus. Using this technique, melts of known composition were made and a phase diagram near the liquidus is proposed based on the microstructures resulting when these melts were quenched. EXPERIMENTAL The Nb-Sn alloys weighing 0.7 g each were prepared in the form of cylinders. Niobium powder, -200, +325 mesh, and tin shavings with a minute amount of tin powder for a binder were mixed in the desired proportions and cold-pressed at 50,000 psi in a 0.150-in. die. This cylinder was then enclosed as shown in Fig. 1, and the entire arrangement mounted in a 2.6-in. pyrophyllite tetrahedron.&apos; The desired temperatures (-2500°C) presented several problems in high-pressure container materials. Boron nitride, the usual sample holder, was found to react with niobium to form the nitride. However, MgO cans and plugs machined from refractory rods did not melt nor react with the sample. Thick tantalum contact disks were used to carry the large currents (~450 amps) to the graphite heater, since tantalum did not melt and had enough strength to prevent extrusion of the sample. It was further observed that the graphite heater and tantalum disks could not be in direct contact with the pyrophyllite because it melts and decomposes at these temperatures to kyanite and coesite (SiO2),2 the former reacting with graphite and the latter with tantalum to form the silicide. The use of a MgO outer sleeve

Jan 1, 1965

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

In the spring of 1944 the Congress passed Public Law 290 (58 Stat. 190, 30 U. S. C. Sec. 321) "authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes." Section 2 reads: "In order to carry out the purpose of this act, the Secretary of the Interior is authorized- (a) to conduct laboratory research and development work, and, with pilot plants and semi-works plants, to make careful process engineering studies, along with structural engineering studies, in order to ascertain lowest investment and operating costs necessary to determine the best demonstration plant designs and conditions of operation;

Jan 1, 1948