Search Documents

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By Robert W. Elayer

For the design of a coal mine and process plant, a comprehensive foundation of geologic information is essential. Historically, the development, collation, and use of this information for design have been costly and time consuming. With the application of a digital computer, however, the effort expended can be reduced and maximum effective use of the geologic information realized. The purpose of this paper is to demonstrate the feasibility and convenience of using a computer to Store and manipulate geologic data for use in mine and process plant design.

Jan 1, 1975

By Engineering Staff

"This paper briefly describes the surface mining operations at Smoky River Coal Limited (formerly McIntyre Mines Limited, Coal Division) near Grande Cache, Alberta. Geology, mining methods, equipment, manpower and reclamation and environment topics are discussed. Introduction Smoky River Coal Limited, a wholly-owned subsidiary of McIntyre Mines Limited of Calgary, Alberta, produces a high quality, low sulphur, low volatile bituminous coking coal from its minesite located at west central Alberta, approximately 20 km from the town of Grande Cache and 360 km west of Edmonton (Fig. I). Most of the coal property is contained within a 30 km long by 20 km wide block lying in a northwest-southeast direction in mountainous terrain. Elevations vary from 920 m above sea level ·at the plant·site on the Smoky River to 1,600 mat the upper levels of current and proposed mining operations. A total of 11 coal seams have been identified. Only two seams, No. 4 Seam and No. 10 Seam are currently considered of major commercial value. These seams are recovered by both surface and underground mining. Approximately 650Jo of the plant feed coal is obtained from a conventional shovel/truck surface mine; the balance is mined underground by room-andpillar methods. Background In 1921, McIntyre Mines Limited acquired some 26,300 hectares of coal leases at Smoky River. Since then the leases were explored intermittently by different companies including McIntyre. In the mid-l 960s exploration activities increased and several feasibility studies were completed. Development of the area was undertaken by McIntyre in 1968 and, in August of the same year, a long-term contract was signed with a consortium of Japanese steel mills for delivery of 2 x 106 t of clean coking coal for 15 years commencing in 1970. Production was focussed on underground mining, using longwall methods."

Jan 1, 1985

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

"Minerals in Transition" is the timely theme of this year's SME-AIME Fall Meeting and Exhibit, to be held September 10-12 at the Salt Palace, Salt Lake City, Utah. Approximately 2000 members and guests are expected to attend the meeting, which will include 117 technical papers, presented during 27 sessions. To complement the technical program, a record number of mining manufacturers and suppliers will be on hand to exhibit the latest in equipment innovation and professional services.

Jan 8, 1975

By Wainer da Silveira e Silva, Marco Antonio Teixeira, Robisom Damasceno Calado, Carlos Alberto Chaves, Tone Takayama Filho

A preocupação com o adequado tratamento de resíduos industriais surgiu com o conceito de desenvolvimento sustentável criado pelo Clube de Roma e contribuiu para o uso racional dos recursos naturais ao longo dos últimos 50 anos. A preocupação com a produção responsável e uso judicioso de recursos naturais priorizou a reciclagem de materiais na agenda das empresas, tornando-se numa atividade de alta relevância, vital para a sustentabilidade econômica e ambiental. Este trabalho aborda os aspectos técnicos, econômicos e ambientais da reciclagem de resíduos contendo zinco através do estudo de caso de reciclagem de resíduos gerados no processo de fabricação de aço em Forno Elétrico, denominado pó de Aciaria Elétrica (PAE). A indústria ainda está em busca de tecnologias para redução da geração e reciclagem desse resíduo. A relevância do estudo está na utilização da Análise Hierárquica de Processo (AHP) para avaliação e seleção da melhor alternativa, entre várias, para tratamento e reciclagem do PAE. Como resultado, demonstrou-se a eficácia do uso da metodologia no empreendimento de reciclagem de resíduos contendo zinco implantado pela Votorantim, em Juiz de Fora, Minas Gerais.

Nov 12, 2019

By Glenn C. Reed

This report is one of a series describing investigations within the Missouri River Basin in Montana made by mining engineers of the Bureau of Mines Minerals Division, Region II. The primary purpose of these investigations is to provide information to agencies of the Department of the Interior and and others concerned with the planning of Federal power developments in the basin. The report contains such factual data as have been authorized for public distribution. The field investigations in Broadwater County were made during the late fall of 1948 and the summer of 1949. Virtually all known metallic mineral deposits and some nonmetallic mineral deposits within the county were investigated. However, some long inactive mines and prospects on which little or no information is of record may have been omitted inadvertently. Many of the mines and prospects have been inactive for extended periods. Most of the underground workings now are inaccessible. Because of such conditions, impressions gained by the inspection of surface features have been supplemented necessarily, where possible, by information obtained from Federal and State publications.

Jan 1, 1951

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By Pedro Hugo Tumialán

El presente texto describe el proceso de mineralización de la mina Farallón, la cual está ubicada en la provincia de Huarochirí, Lima. Este yacimiento polimetálico produce principalmente zinc, cobre, plomo, plata, oro, donde la longitud total inclinada de mineralización es de 600 m. Asimismo, la silificación se da en toda la roca con rasgos de caolinización, sericitización y propilitización de menor temperatura y la mayor área mineralizada se encuentra en el intrusivo, en menor proporción por el lado volcánico.

Apr 1, 1991

By Y Ren

The algorithms employed by the commercial tools are either heuristic algorithm or iterative optimisation of a subsystem. This often results in a suboptimal schedule. In this paper, the author presents a new scheduling algorithm that incorporates with a novel stockpile configuration system, an improved algorithm on multiple processes and a mixed-integer linear programming (MILP) global optimisation model. It can simultaneously optimise stockpiles, blending, multiple processes as well as multiple mines. In addition, it allows the user to interact with the solution to adjust the solution to be practical and desirable.CITATION:Ren, Y, 2013. A simultaneous optimisation tool for open pit mine scheduling, in Proceedings World Gold 2013 , pp 427-432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1968-69. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By J. M. Singer

Quenching distances for flames of methane-coal dust mixtures were determined with air and oxygen-enriched air. Coals used were Pittsburgh, Sewell, and Pocahontas No.3. Quenching distances were greater for flames of hybrid mixtures of coal dust and methane than for methane flames of corresponding stoichiometry. From the data of quenching distances and methane-coal dust concentrations was calculated the quenching equivalence, which is the increase in coal dust concentration required to maintain a given quenching distance value as the methane concentration decreases. These equivalences could be useful in identifying hazardous methane-coal dust mixtures in mines.

Jan 1, 1966

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By J. H. Holden

The Federal Bureau of Mines is doing research and development work on a pressure-gasification pilot plant for producing synthesis gas directly from pulverized coal, oxygen, and steam. A pressure-gasification pilot plant has been constructed, and an investigation was made with the following basic objectives: 1. Determining the effect of varying pressure (75, 100, 150, and 300 p.s.i.g.), coal rate (400, 700, and 1,000 pounds per hour), and oxygen-to-coal ratio (8 to 11 std, c,f. per pound), on percentage of carbon gasified, oxygen and coal requirements per unit of CO + H2 produced, exit-gas temperature, and heat loss. The steam-to-coal ratio was maintained at approximately 0.3 pound per pound. 2. Development of a stabilized gasification zone or reaction space. 3. Improvement in operability of the pilot plant.

Jan 1, 1960

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Aug 1, 2009

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines. Companies In 2007, a total of 2,999 contracting companies reported employment at coal mines to MSHA, or 35.7% of all independent contracting companies.

Aug 1, 2009

In 2007, a total of 278 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 44.6% (n=124) of all metal mining operations. Other common types of metal mines were iron ore (n=36; 12.9%) and copper ore (n=35; 12.6%). ? Nevada had the largest number of metal mines (n=45; 16.2%), followed by Alaska (n=28; 10.1%).

Aug 1, 2009

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By Mario Del Risco V

El presente trabajo señala los diseños de fracturamiento hidráulico en los pozos de petróleo, donde se experimenta los nuevos fluídos y aditivos y se perfeccionan los procedimientos utilizados. Asimismo se describe el diseño, ejecución, clases de fracturamiento y costos del mantenimiento de este tipo de operación.

Nov 20, 1967