Search Documents

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012

By W. P. Yang, L. B. Berger, G. W. Jones

"Any burning carbonaceous material, unless supplied with enough oxygen for complete combustion, will liberate carbon monoxide. Since tobacco in its many different forms consists largely of carbonaceous material, and duo to the conditions under which it is smoked (burned), carbon monoxide should be liberated. That this is true has been shown by Armstrong.***** who found that undiluted smoke from cigars contained in some tests more than 3.00 per cent carbon monoxide, the amount present depending upon the size and closeness of packing of the tobacco during manufacture and on the rate of burning.****** Cigarets gave much less CO, varying from 0.06 to 1.40 per cent. The rate of consumption and carbon content of the tobacco are not g.ven, so that a correlation of the values reported to conditions in closed spaces where people might be assembled are difficult, if not impossible.The Bureau of Mines is interested in the general question of carbon-monoxide hazards from tobacco smoke, mainly with regard to mine ventilation. In non-gaseous mines, especially metal mines, the question arises, whether, if groups of miners are permitted to smoke while working at unventilated faces or entries, would the accumulation of tobacco smoke in these places create an' additional hazards the to carbon-monoxide poisoning. The results should, in addition be of general interest in connection with ventilation of building and inclosed places where people may be assembled and smoking is permitted. The investigation described in this report was made with the above idea in view."

Oct 1, 1923

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By D. Harrington

[Notwithstanding the fact that it is now fairly generally recognized that widespread explosions can be almost absolutely prevented in coal mines by efficient rock-dusting and that this rock-dusting can be done thoroughly at a cost which should seldom exceed 1 cent per ton of coal mined, a recent survey of the situation by the Safety Division of the U. S. Bureau of Mines, following a similar survey by the Bureau in the fall of 1925, shows that while some progress is being made by our coal-mining people, many entire mining communities are lamentably slow in taking advantage of one of the most effective safeguards available. Much of the information as to the extent of rock-dusting was obtained through the various State inspection departments. Table 1 shows that in the fall of 1925 about 92 coal companies in the United States were using rock-dust ad that in the summer of 1927 the number had increased to 239, or about 160 per cent increase. Similarly, from the fall of 1925 to the summer of 1927 the number of mines using rock-dust increased from 177 to 463, or about 160 per cent increase. This appears to be a decidedly healthy increase, but when it is considered that in 1926 (the last date for which figures are available) there were 7,141 bituminous mines operating and that there were only 463 or 61 par cent, which were even reported to Ice using rock-dust to any extent whatever, the forgoing figures as to progress are by no means impressive or even satisfactory.]

Jan 1, 1928

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967

By S. Mendenhall

The Golden Sunlight Mine (GSM) began operation in 1982 with a strong commitment to environmental stewardship and the local community. This commitment ensured the long-term physical, chemical and ecological stability of the mine site and maintained an active partnership with local stakeholders. Concerns for economic development intensified as mine closure loomed on the horizon and fostered the inception of the Community Transition Advisory Committee(CTAC).This coalition of interested area stakeholders has the primary focus to sustain current mining operations while concurrently seeking alternative post-mine economic development opportunities utilizing existing mine assets. Accomplishments include development of an Asset Re-utilization and Post-closure Plan, a community survey regarding the impending mine closure, recruiting an international wind energy company to develop a wind farm, and development of an industrial/business park. The synergy of this strong partnership is key to meeting sustainability goals and enhancing potential future mining operations. The cooperative effort of the GSM and the local stakeholders is a success story that could be a role model for other mining operations.

Jan 1, 2004

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

By A E. Annels, G F. Johansen, B W. Cuffley

Nuggety gold-quartz reefs are characterised by localised, high-grades and in many cases coarse free-gold. Geometrical and grade complexities are often observed. The high-grade regions are generally erratic and have a low continuity; though may make the deposit economic. Viable grades are generally contained within discrete oreshoots, which are surrounded by barren/low-grade material. Drilling is an effective measure of geological continuity, however grade distribution can only be reliably obtained from underground development and bulk sampling. In general terms, only an inferred resource is likely to be estimated from surface drill data alone. Underground development, further drilling and probably bulk sampling will be required to delineate inferred and indicated resources. Closely spaced development with bulk sampling is likely to be the best way to determine a probable reserve. The resource evaluation process must driven by a clear geological model that should attempt to understand the controls to reef geometry and grade distribution. Geological interpretation has traditionally been undertaken in two-dimensions, though computer software is now being used to produce three-dimensional models. Grade interpolation has generally been undertaken using classical methods, typically weighted averages, zone of influence weighting and polygonal/sectional blocks. Tonnages can generally be calculated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because of its highly erratic and discontinuous nature. To account for variability it is recommended that a best estimate be reported within a grade range, as this more accurately reflects the uncertainties involved. Reporting should be undertaken within the framework of the JORC code, but should involve special consideration of grade reliability.

Jan 1, 2000

By Paul C. Miclea

In case of a major fire in a tunnel between stations or ventilation shafts, if the buoyancy effect of the hot gasses is stronger than the airflow induced by the fans, the risk of backlayering could restrict the safe evacuation of people. Obstructions in the tunnel and alternate airflow paths can further reduce the air velocities past the fire. Currently there are two computer programs available to address the issue of underground fires: o "Subway Environment Simulation" (SES), Version 3.0, developed by Associated Engineers, a Joint Venture of Parsons Brinckerhoff Quade & Douglas, Inc., De Leuw Cather & Co., and Kaiser Engineers, Inc. for the U.S. Department of Transportation o "MFIRE", Version 1.26, developed at Michigan Technological University for the U.S. Department of the Interior, Bureau of Mines. As implied by its name, the SES program was developed specifically for the analysis of subway ventilation systems. It can be used to analyze the heat released into, and removed from, a subway or vehicular tunnel and to determine the effect of ventilation elements on airflows throughout the network of stations or other merging tunnels. It has a special feature allowing the user to predict the effects of a fire at any location within the subway system. Version 3.0 of the SES program is designed to be used with a "critical velocity" calculation in order to determine whether or not tunnel airflows can be controlled during a train fire emergency. The original version of the program was written in FORTRAN for mainframe computers, such as the IBM 4381. Recently ICF Kaiser Engineers has compiled a version of the SES program for PC use. The MFIRE program simulates the interdependence between a mine ventilation system, with its pertinent fans and structures, and changes in ambient conditions or a source of heat, such as a fire. It also accounts for natural ventilation. The program is written in FORTRAN 77 and compiled for 8086/8088 based microprocessors, allowing it to be run on an IBM PC or compatible computer with a 2.0 or a later version of DOS, 256K random access memory (RAM), and a text editor. This paper reports the comparative results of an application of both programs for the same network in a recent study.

Jan 1, 1991

Gas dynamic phenomena, particularly instantaneous outbursts of coal and gas are problems experienced in gassy, highly stressed coal, both usually the result of depth. Diff- erent mining geometries present different opportunities for seam gas to escape, starting from the virgin condition unaffected by mining and ending with the mining of the coal. The mining of the coal varies from entering a virgin seam cross-measure, heading out into virgin seam, advancing longwall faces into virgin seam and extracting developed blocks from large longwall retreating blocks to small pillars. Each method has its particular gass- iness patterns and particular stress patterns, both changing to some extent with time, and changing as mining progresses. Geological structural anomalies are the cause of gas and stress anomalies, causing in turn greater gas and stress manifestations. Pre-drainage of gas from the working seam not only degasifies the coal but causes it to shrink and so may affect stress as well as gas patterns. Unfortunately prior degasification is not all benefit, and there are some d13- advantages to its use. Also although it is possible to degasify places ahead, gassiness will return if drainage holes are shut down or sealed up and other deleterious aspects may be induced. Research should continue into the problem of instantaneous outbursts of coal and Gas.

Jan 1, 1986

By Mônica Aline Magalhães Gurgel

O presente trabalho estudou a evolução microestrutural durante o recozimento no campo intercrítico de um aço baixo carbono com micro-adição de nióbio e molibdênio, laminado a frio, destinado a indústria automobilística, sendo este material da classe dos aços bifásicos. Com o intuito de verificar se os parâmetros utilizados no processo de fabricação (laminação a quente e a frio em função de uma determinada composição química) foram definidos de forma eficaz para obtenção da microestrutura esperada para um material “Dual Phase”. Os estudos foram suportados pelas análises da evolução microestrutural durante o processo de recozimento em escala laboratorial e análise dilatométrica, com o objetivo de determinar a faixa de temperatura no tratamento de recozimento em que as melhores propriedades foram atingidas. As caracterizações microestruturais e mecânicas foram avaliadas por Microscopia Óptica, Microscopia Eletrônica de Varredura (MEV) e ensaios de dureza Vickers.

Jul 30, 2018

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

By F van de Venter, J Monama, T Kale

For a multitude of years fine iron ore, -1 mm, across the world has been deposited as discard material in tailings facilities. This contributes to environmental problems, decreases plant yield and increases the cost of processing. Fine iron ore recovery processes are often deemed unfeasible or uneconomical, due to the complexity of the reclamation thereof in comparison with high-grade ores. However, recent advances in the recovery of fine iron ore using the Optima Classifier® has shown great promise. The Optima Classifier® is a new hindered settling separator that makes use of an upward current of water for density separation. It’s unique design combines three different separating zones for increased efficiency and recovery. In this study the potential of the Optima Classifier® to produce a +63 per cent Fe concentrate from -1 mm feed material was evaluated from a standalone and process perspective. It was found that a +63 per cent Fe product can be produced from a single stage, using the Optima Classifier®. Fine iron ore feed with an average head grade of 50 per cent Fe was upgraded to average concentrate grades of 63.2 per cent Fe. Displaying upgrade ratios of up to 1.26 in a single stage. A three-stage, rougher, cleaner and scavenger system did however show the best performance with recoveries of up to 70 per cent, yielding 56 per cent of a 63 per cent Fe product. Furthermore, the dewatering of the product and tailings was evaluated using the UltraG ultra-fine dewatering screen ensuring dry, stackable material. The tailings could be used in codisposal, while loads on thickeners and filter presses are significantly reduced. The high throughput of the Optima Classifier® ensures a small plant footprint, minimal civil and structural requirements and low operating utility consumption such as electricity, minimising the carbon footprint of a fines beneficiation plant. The Optima Classifier® in combination with the UltraG dewatering technology has provided a platform for economical recovery of fine iron ore, both current arising and historical. Providing opportunity to lower plant operating costs, reduce environmental liability of tailings facilities and increasing immediate process water recovery

Sep 18, 2023

By Edmund Cardoza

In the spring of 1993, construction began on an ambitious building project in Boston, Massachusetts. The Shriners organization committed to offer state-of-the-art adolescent burn treatment and rehabilitation in its Boston facility by expanding in a most unusual way. In short, the concept included installation of caisson foundations and perimeter slurry wall panels to enable construction of a completely independent structure around and above the existing, continually functioning, hospital. Two distinct phases of work were detailed in the Contract Documents. At the completion of the first phase, patients will be moved into the new building, above, and demolition of the old structure, beneath, will be performed. In Phase I, sections of the slurry wall and caissons, located outside the footprint of the existing building, were planned. The next phase of the work includes the installation of the remaining caissons and slurry wall. Once excavation is completed, the balance of the new hospital structure will be constructed from the bottom upward, connecting to the under side of the new structure.

Jan 1, 1994

By K. E. Stanfield

The oil yields of sections of Green River oil shale in Colorado, Utah, and Wyoming are presented as part of a continuing project to determine oil-shale reserves in the United States. Oil-yield logs, based upon analyses obtained from 1945 through 1952, are presented to show the thickness and richness of 202 sections of Green River oil shale. The logs are based on analyses of approximately 20,500 samples, representing 179,000 feet of shale, which were made by the Bureau of Mines, and upon analyses, representing approximately 26,000 feet of shale, which were made by other agencies. The samples consisted of cores from a Bureau of Mines coring program in U. S. Naval Oil-Shale Reserve 1, Garfield County, Colo., and cores, drill cuttings, and channel samples provided by other agencies, chiefly oil companies. Most of the samples of oil shale from Utah and Wyoming were derived from oil-well drilling operations. As a result, the oil-shale sections were widely scattered and were not extensive or reliable enough to be representative of the significant deposits of Green River oil shale in these States. The oil-shale sections for Colorado, however, were more comprehensive, and a number of the sections were used in a previous report as a basis for estimating oil-shale reserves in Colorado. The present report does not give estimates of oil-shale reserves but is limited to presentation of oil-shale analyses that may be used for future reserve estimates. Other sections of Green River oil shale are being analyzed, and the results will be published in subsequent reports.

Jan 1, 1954

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968