Search Documents

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974

For some time fine coal (-0.5 mm) flot ation has been considered as a bulk flotation problem. Combinations of hydrocarbon oils and frothers have been used as surface active agents in coal flotation. The selectivity of the flotation process has always been poor in such cases. With the increase in fine coal production due to mining methods and coal handling systems, optimisation of fine coal treatment.has become important. Petrographic and mineralogical composit- ions of coal particles have been reported to influence their flotability. The problem becomes more complex due to surface oxidation of coal and the presence of slime forming clay minerals in the run of mine coal. In this paper, the flotation problem is examined on the basis of various constituents of coal and their associated gangue minerals. The selection of reagents has been suggested on the basis of their surface chemical properties. Factors such as surface modific- ation of coal and gangue materials, flotation kinetics and hydrocarbon oil - coal inter- action have been critically evaluated to improve fine coal flotation recovery.

Jan 1, 1978

CHAIRMAN EMRICK: We have a very interesting program this morning, of a mechanical nature, and I am sure you will all be very much interested in it. At the conclusion of each paper there will be time given for discussion, and we will be glad to have all of you enter into the discussion. Before we start the program, I want to ask the men who have been appointed chairmen of committees to come and get these folios, which contain papers concerning their particular committees. The Nominations Committee, of which David Brown is chairman, has a folio here. It has been customary every year to have a photograph of those in attendance taken, and I presume it is the will of those in attendance this morning to have their pictures taken. We plan to do that about a quarter of twelve, approximately, this morning in the room instead of going outside as we have heretofore. Frank Miller has an interesting an¬nouncement to make. Frank, if you will just take about five minutes to tell your story.

Jan 1, 1934

By Harold Bailie

The purpose of this Bureau of Mines report is to furnish information on mining practices applied to flat-bedded fluorspar deposits in southern Illinois. It presents new and improved operating procedures and specialized techniques applicable to deposits of this type. All of the operating mines of the Ozark-Mahoning Co. in this area have been opened by vertical shafts which connect with levels consisting of haul-age ways, stopes, and loading stations. The stoping practice used locally called room and pillar, is open stoping with pillars left at different distances and diameters. To facilitate haulage and drainage, the mines are worked from openings turned off the main haulage drift on a grade to conform with the dip of the ore beds. The ore is predominantly fluorspar with smaller amounts of galena and sphalerite that contain traces of cadmium and germanium. The principal gangue minerals are limestone, calcite, shale, barite, and sandstone. The rock hardness ranges from relatively soft shale to hard, abrasive sandstone.

Jan 1, 1960

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986

I WISH to express to the members of the Institute my sincere appreciation of the distinction which they have conferred upon me by again making me their president. It also gives me great pleasure to once more welcome the Institute to Mount Lyell.Since your last visit certain improvements in plant have been made, which I trust you will have found interesting, and which show that, though located in a remote corner of the world, we are abreast of the times.The opportunities which a recent lengthy trip to America has given me to observe the degree of interest which our local smelting practice continues to arouse in metallurgical circles make it seem appropriate that I should take advantage of your visit to lay before you some detailed information on the more practical features of pyrite smelting, particularly as carried out at Mount Lyell. There are only a few places in the world where the method is now being practised in approximate purity-only about half...

Jan 1, 1915

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By M. N. Short, I. A. Ettlinger

M. N. Short,? Washington, D. C., and I. A. Ettlinger, New York', N. Y. (New York Meeting. February, 1926) The Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a, confused series of mountain ranges of moderate height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County. The Magma copper mine (Fig. 1) is the only producer in the district. Although discovered in 1875, its production has been important only

Jan 1, 1927

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By L. H. Rajala, K. H. Singh

"This paper presents the results of a detailed feasibility study carried out to investigate whether a low-grade deep underground mine of Falconbridge Nickel Mines Ltd., closed since 1975, could be made more productive and profitable by the introduction of new mining technology. For this purpose, recent advances in mine design and development concepts, larger and better designed machines, such as hydraulic drills, high-pressure down-the-hole machines, LHDs, new blasting concepts, more efficient and improved stoping methods, and ground control technology were considered. Technical and economic analyses incorporated the latest computer-based techniques. The mine was reopened in 1979 and the paper concludes with an assessment of actual progress and performance compared with that planned and forecast.IntroductionThe East Mine orebody, located between the Falconbridge Mine and Inco's Cryderman Mine in the Sudbury District of Ontario, has been in production since 1956. From 1956 to 1978, about 5.6 million tons of ore had been mined from this ore zone. The ore body is low grade and was developed as a cut-and-fill operation. Due to high operating costs, the mine has been shut down several times during economic downturns. The latest closure was in 1975 due to a lower demand for metal.In 1978, investigations were initiated to assess the economic and technical feasibility of mining this ore using new developments in mining technology. In this study, consideration was given to the application of bulk mining methods with a potential for higher productivity, trackless development utilizing efficient LHD machines and hydraulic drills, new blasting and fragmentation concepts, and new ground control technology. Advanced computer techniques, such as finite element, for mine design and rate of return with discounted cash flow analyses for the economic comparison- of various mining options were utilized for a rapid and comprehensive assessment during the feasibility stage."

Jan 1, 1981

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By Weber W

Methods of calculation of the reliability of process computers are getting more and more important. The paper presents long period observations of 21 process computers with online applications in the iron and steel industry. About 5000 failure events during 10 years have been systematically recorded and evaluated. On the basis of these long time observations it is possible to develop a probability model of the failure behaviour of process computers.This failure model is constructed with four different states of the process computer:Working phase, working phase with undetected reasons, repair phase, failure phase resulting from external influences.The model is defined by differential equations for the probability of one of these four phases. Long time observations show, that all of these four phases are closely correlated with the capa-city of a process computer, restarting without detection of failure reason, changes of programs and software, costs and time of repair. So the result of this analysis is a model of failure for process computers, which allows to predict breakdowns of process computers on the basis of external parameters.

Jan 1, 1985

By R. C. Gilmore

Underground longwall coal mining sections may develop explosive mixtures of methane-air in the mined-out gobs. If the panel are operated as bleederless or sealed gobs, progressive sealing along the gate roads as the longwall face retreats limits the flow of fresh air into the gob and thus deprives potentially explosive atmospheres of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics (CFD) modelling to simulate the flow of gases in longwall gobs. Modelling indicates that targeted injection of nitrogen through the seals along the gate roads inbye the face can be used to control the size and location of methane and air clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures in longwall gobs.

Aug 1, 2013

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes hack well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948. Summary Of the eight million tons of coal mined in the two states in 1947. ap- proximately two million tons were washed in wet washing plants, using concentrating tables or jigs. The one table plant accounted for 70 pct of the output of washed coal, and two large Baum jig plants accounted for an additional 26 pct, leaving only a small residual tonnage to be accounted for by other types of jigs The necessity for washing coal is occasioned by the desire or necessity of reducing the ash content of the coals— sulphur is not a problem in this area. All washeries, except the table plant, are at or near the tipple, hence wash only one kind of coal. At the table plant a large number of different coals are washed. Only at the table plant is there any occasion for drying any considerable quantity of fine coal— other plants size and/or dewater on shaking screens. The results of washing at the smaller plants are judged by the number (or lack) of complaints about the quality of the washed coal. This is probably as good a system as can he devised for small, intermittent operations. The efficiency of the Baum jig ap-pears to be quite high. This is to be expected as long as the automatic control of the refuse gate operates properly. The efficiency of the concentrating table is not as high as that of the Baum jig, especially when the "difficulty" of washing is taken into consideration. When dealing with coals in which the "bone" is larger than the "coal," the table appears to be at a definite disadvantage, because of its sizing action.

Jan 1, 1950