Search Documents

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By A. Dutta, B. Devulapalli, A. Mukhopadhyay, E. W. Grald

"Computational Fluid Dynamics (CFO) has matured over the past two decades as an analysis tool for conducting virtual experiments with significant time and cost savings. It complements and reduces physical testing. CFO has penetrated the diverse materials industry in much the same way as Computer Aided Design (CAD) did more than a decade ago. As the basic numerical algorithms used in CFO have steadily improved, so have the reliability, consistency and user-friendliness improved significantly, too. Other recent trends have also contributed to the rapid growth and widespread adoption of CFO. In this presentation, CFO applications from several materials processing industries will be presented using case studies. Emphasis will be on metals, glass and semiconductor applications.IntroductionThe term materials processing covers a diverse array of industrial applications and products today. From the continuous casting of steel, to the deposition of semiconductor materials atom by atom, to the extrusion of molten polymers, materials processing applications span an incredible range of length scale, process times, pressures, temperatures and velocities. The properties of the materials themselves, in terms of density, viscosity, thermal conductivity, etc., can be complex functions of temperature, shear rate, chemical composition and time. And the processing equipment may be very complicated in geometric shape.Computational fluid dynamics (CFD), the technique of solving the governing equations of fluid motion and other related phenomena using a computer, has enjoyed widespread and rapid growth, which started in the aerospace and automotive industries. More recently, CFD has also been successfully applied to a great many materials processing problems, in spite of the challenges described in the previous paragraph. The reasons for the growing usage of CFD in materials processing are many. Using CFD to test design options and reduce the number of physical prototypes can decrease the time and cost associated with new product and process development. CFD gives insight and provides detailed predictions of operating conditions in lieu of difficult, intrusive and often expensive experimental methods. CFD can be used as an aid to scale-up processes from lab or pilot scale to full production. Troubleshooting the performance of existing equipment is often carried out with the help of CFD. Determining how an existing piece of process equipment will operate under new conditions, or with new input ,materials, is also a common task for CFD."

Jan 1, 2004

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By Byron A. Baker

The Bureau of Mines used a windowed cell to measure the phase-boundary pressures of two related series of gas-condensate fluid mixtures. Normal butane was added to the mixtures incrementally to determine its effectiveness for lowering phase-boundary pressure. All the experimental data were correlated, so that the pressure required to maintain light oils mixed with natural gas in the single phase may be computed for secondary recovery applications. The heavy hydrocarbon parts of the mixtures were distillation fractions of a Gulf Coast condensate. Intermediate normal hydrocarbons in the butane-heptane range and natural gas were added to the fractions in selected proportions, so that phase-diagram pressures of 26 fluids were actually studied. The experimental range of temperatures was 50° to 280° F. Two correlations were developed to represent phase-boundary pressures by means of a polynomial. Independent variables represent natural gas content, disparity of properties of components comprising the mixtures, and temperature. A fourth variable, for one correlation only, was the quantity of normal butane added to the original mixtures. The latter correlation with four independent variables contains 15 coefficients and is estimated to be accurate to 135 psi.

Jan 1, 1973

By David C. Chang

A survey of in-situ methods for determining bulk electric properties of coal is given. Largely because of the strong dependence of coals properties on operating frequency, different sensing methods have to be adopted for different applications. Evaluation of both established and feasible methods is made in this report from the viewpoint of physical set-up, probing depth, and the type of inversion involved.

Jan 1, 1977

By A. D. Hughes

C. W. MERRILL*-Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably, a matter of vital interest.

Jan 1, 1949

Access to the Rosebery Orebody, which dips into the western slopes of Mount Black at 45¦, has been achieved in sequence by the following means: - A series of adits down to 8 level - An inclined shaft (No. 1 Shaft) sunk internally from 8 level to 14 level - A vertical circular concrete lined shaft (No. 2 Shaft) sunk internally from 4 level to 19 level. Although the orebody has been fairly well defined to 19 level, deeper ore occurrences have been outlined by a series of drill holes decreasing in frequency with depth to 26 level. No. 2 Shaft (sink) was stopped some 10 m below 19 level in order to make an early start on doubled production at West Coast Mines, with the intention of subsequently extending the shaft or of driving a decline from the lowest operating horizon for deeper access. The decline approach was adopted some six years after production commenced from No. 2 Shaft. The reasons for that decision are outlined, together with an account of the constraints and design requirements imposed by commencing by a vertical shaft in the hanging wall of the orebody.

Jan 1, 1982

By P. R. Ineson, D. W. James

For a criterion to be useful it must either demonstrate directly the role of exhalative processes in the formation of a deposit or describe a unique attribute of exhalative deposits. Few of those employed in previous investigations entirely satisfy either condition. The limitations of three of the most frequently employed criteria are illustrated by studies of the geology of the King Island Scheelite deposit in Tasmania.

Jan 12, 1993

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Alexandre Aparecida Morais

No Lingotamento Contínuo de Planos (placas de aço) o número de corridas realizadas em um único distribuidor é um indicador de performance operacional de enorme relevância para a sustentabilidade do processo. Ligados ao desempenho deste indicador estão os resultados de índices como produtividade, redução de custos, segurança e qualidade. Buscando melhorar este indicador a ArcelorMittal Aços Planos América do Sul – Unidade Tubarão iniciou no final de 2012 um projeto multisetorial subdividido em vários subprojetos satélites para aumentar o número de corridas em um único distribuidor visando obter ganhos nos índices técnicos descritos anteriormente. A proposta de meta oriunda deste projeto visava aumentar em no mínimo 70% os valores médios de corridas em um único distribuidor no Lingotamento Contínuo de Placas, o que representaria ganhos superiores a 1,2 milhões de dólares por ano. Neste trabalho é apresentada a metodologia definida para o projeto com suas respectivas etapas, o resumo de alguns subprojetos de sustentação e os resultados que já foram atingidos.

Aug 16, 2017

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By Juver Vélez

Este método de exploración consiste en la introducción con un equipo mecánico - hidráulico que ejerce presión y rotación sobre un tubo de metal el cual tiene en su inicio una corona con diamantes impregnados (denominada broca), al interior de la corteza terrestre, con el objetivo de extraer el material roca de profundidades a la superficie para realizar su identificación geológica y análisis varios; La perforación diamantina ha venido desarrollándose a través del tiempo y con la experiencia de los operadores, llegando a crear máquinas de gran capacidad para alcanzar grandes longitudes.

Sep 1, 2017

By H Hoogvliet

The Goondicum Crater industrial minerals deposit is located about 30 km east of Monto, Central Queensland, Australia. Early exploration programs in the 1990s found alluvial ilmenite along the banks of the Burnett River. This mineralisation was traced upstream to the Goondicum Crater. The Goondicum Crater is a topographic feature centred on a roughly circular 6 km diameter layered gabbro complex. Significant ilmenite, apatite, titano-magnetite and feldspar mineralisation are present in a weathered horizon up to 25 m thick. After several drilling campaigns in the Crater and subsequent feasibility studies, the project was developed by Monto Minerals Ltd, an ASX listed company, in 2007. However, the project never achieved production performance expectations and ran out of commissioning funds. The company subsequently went into voluntary administration in August 2008.In 2009, the RMM Capital group, of Brisbane, took control of Monto Resources Pty Ltd, and renamed the company Belridge Enterprises Pty Ltd (Belridge). Belridge commissioned a redevelopment study aimed at recommencing mining and processing operations. As part of the redevelopment study the authors planned a drilling campaign, managed a quality control program and developed a block model. This paper describes the drilling program, analytical procedures, quality control procedures and the preparation of the block model.The block model for the resource estimate was created using 1 m high blocks, wireframes defining the main material types, and 2.5 m thick horizontal search ellipsoids with a radial pattern. The deposit was ‘flattened’ prior to modelling. To assist with the economic evaluation of the project, each block in the model was assigned a net dollar value based on economic parameters provided by Belridge, including anticipated revenues and costs. This modelling technique allowed for efficient investigation of various scenarios and was used extensively in the development and optimisation of the project’s financial model. At a zero net value per block, comparable to a break-even cut-off grade of four per cent ilmenite equivalent, the Indicated plus Measured resource is estimated at 51 Mt, averaging 4.1 per cent ilmenite, 1.9 per cent apatite and 2.5 per cent titano-magnetite.

Oct 5, 2011