Search Documents

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By Hill G

The Boddington Gold Mine (BGM) is managed by Worsley Alumina Pty Ltd (Worsley) and is located 110 km south-east of Perth, Western Australia. The gold mine, which has operated since mid-1987, was originally constructed to treat 3 Mtpa of gold bearing oxide ores, has subsequently been expanded to treat 7 Mtpa and is presently one of the largest gold producing operations in Australia.During 1990 a Supergene/Basement Plant was constructed to treat 250 000 tpa of copper supergene and hypogene ores and basement ores which contain significant gold grades and which are encountered at the lower levels of the existing oxide orebody. The SupergeneBasement Plant has the versatility to treat a wide range of ore types, producing both gold bullion and copper-gold concentrates. It is a stand-alone facility adjacent to the existing 7 Mtpa gold plant.

Jan 1, 1992

By E. D. Gardner

The American petroleum industry is supplying the present domestic demand for liquid fuels. Known reserves of petroleum in the ground, however, are limited, and the .cost per barrel of finding new oil pools is increasing. Any deficiencies of domestic production in the near future doubtlessly could be made up by imports: Dependence upon foreign oil for part of our industrial requirements is not necessarily cause for alarm, but in time of war an adequate, dependable, domestic source of liquid fuels is vital to the defense of the country. As a national defense measure, and to insure a future continuous oil supply for our economic machine, it would appear logical to take steps now to develop methods for producing petroleum substitutes within our own borders. This undoubtedly was in the mind of Congress when it passed the Synthetic Liquid Fuels Act (58 stat.190; 30 U. S. C. Sup. Secs. 321-325), Approved April 5, 1944.The title' of the Law reads: An Act authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes. Congress authorized $30,000,000 for a 5-year program and directed the Bureau of Mines to carry it out. The part of the program pertaining to oil shale is being conducted on Naval Oil-Shale Reserves Nos. 1 and 3 (fig. 1) at Anvil Points, near Rifle, Colo.

Jan 1, 1948

By R.P. Edwards, B.C. Flintoff

Froth flotation is one of the most widely used and effective processes for mineral benefication. First introduced in 1911, flotation technology has seen many developments over the past 80-plus years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results." Klimpel [1988] While reasonable was sufficient in the past. competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway.

Jan 1, 1995

The Bureau of Mineral Resources has been engaged in regional geological and geophysical field work in the Alligator River and Cobourg Peninsula area since 1971, following the discovery of major uranium deposits. Geophysical work commenced with a regional airborne magnetic and radiometric survey which was followed up by some helicopter and ground work in August 1973. The interpretation of the earlier radiometric work is presented in conjunction with the results obtained from the follow-up work. Analyses of 100 outcrop and drill core samples collected have provided basic information on the physical properties and concentrations of uranium and thorium in various rock types. The uranium determinations were made by X-ray fluorescence and delayed neutron analysis, good agreement being obtained between the two methods. X-ray fluorescence was the main analytical technique used because of its ability to produce both uranium and thorium determinations.

Jan 1, 1975

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By Bernhard Schwab

A popular rule in the mining industry is that a property should only be developed if average unit production cost is less than a given proportion of the estimated long-run price of the mineral. This paper provides a comparative analysis of the average cost approach (ACA) with the use of net present value (NPV) as an investment criterion. It is concluded that the ACA is an easily understood and easily applied rule of thumb which may serve as a rough first screening device, for example in the early stages of deposit exploration. Its operational convenience is at the expense of accuracy and validity, and the NPV provides a sounder method of making decisions, especially in the case of marginal deposits.

Jan 1, 1978

By Maurice Deul

This bulletin summarizes the work conducted under the Bureau of Mines methane control research program during the years 1964 to 1979. This research effort was directed toward improving existing methods and developing alternative methods of reducing the explosion hazard during mining. The research was performed in three general areas: (1) basic factors that control the emission of methane into coal mines, (2) methane control during mining, and (3) methane drainage in advance of mining. Topics discussed in this bulletin include the magnitude of the methane problem; the equipment and instruments developed; the geological, chemical and physical parameters that control the movement of methane in coalbeds; the direct method of determining gas content; the estimates of gas content from adsorption data; and methane drainage, through shafts, through horizontal boreholes, through vertical boreholes, or through slant holes. Improvements in ventilation, control of methane in gob areas, and water infusion are also discussed, as is the potential use of coalbed methane as a supplement to natural gas supplies. This bulletin provides a comprehensive source of information on the accomplishments of the Bureau's methane control research program, on the technology developed, and on the direction of further research.

Jan 1, 1986

By Clifford S. Gibson

THE Workmen's Compensation Ace defines Silicosis as "a fibrocic condition of the lungs caused by the inhalation of silica dust sufficient co produce a lessened capacity for work". This fibrocic condition muse exhibit a specific appearance in the X-ray picture of the chest-an appearance which is not characteristic of several lung conditions which can cause lessened capacity for work and which are not due co silicosis. The layman is sufficiently familiar with this subject co know chat, as far as our knowledge goes, quartz is one of the principal objectionable factors in the production of this condition. He should also know that silicosis respects neither geographical nor industrial boundaries. It is as much a factor in some industrial processes (e.g. foundry work, sandblasting) as it is in mines handling ores containing quartz. Its development co a recognizable stage is usually a matter of many years. As yet, its cure is unknown. Its prevention is possible in varying degrees. The layman should also know that the development of fibrosis may be accelerated by breathing in, or living in, any atmosphere containing dust. Few normal adults, particularly those above a certain age, have clear lungs, and fibrosis in varying degrees is noted in the farmer, the steel worker, the clerk, and many others in varied occupations. It is not restricted to miners. Medical and industrial journals, and at times the press, are crammed with data pertaining to this subject, much of which is misinformation. This is particularly true of certain !laces where the preventive and compensation measures for the good o those earning their livelihood in an industry in which silicosis may be contracted are not so far advanced as in our own Province. A great many of these publishings are alarming to the layman. They leave him with the impression that he is taking his life in his hands if he elects to work underground, particularly in a gold mine-that he has at once sold his heritage of health and chat sooner or later he will succumb to the ravages of this ailment. Nothing could be farther from the truth. Actually, under present conditions in Ontario mines, a very small percentage of the men employed ever become impaired by silicosis to the extent chat they must withdraw from the industry. I propose to tell you briefly something of this subject as it affects our mines.

Jan 1, 1937

By Michael N. Maltezos

"There is certainly no argument that LED lighting systems have taken a strong foothold in the lighting marketplace over the last several years. This has even proven true in the world of transportation and transit lighting, for which new LED cobra head style luminaires are replacing traditional HID cobra head luminaires on North America’s roadwaysand linear LED light fixtures are replacing conventional linear fluorescent light fixtures in North American rail transit facilities. However, LED technology has taken a while longer to penetrate the very specific market of vehicular tunnel lighting in this continent. Though both the New York/New Jersey Holland and Lincoln Tunnels have recently been retrofitted with LED lighting, and an LED Lighting RFP is currently out for Boston’s Central Artery Tunnels, very few vehicular tunnels in North America to date have been illuminated with LED light fixtures. This is largely because cost effective LED lighting, that met our typically stringent tunnel lighting standards, was until recently simply unattainable. However, with the rapid advances in LED technology over recent years, owners and specifiers of North American tunnel lighting projects have finally begun to adopt LED lighting systems as the norm. In fact, a recent Lux Fit/Yole Development “LED in Road and Street Lighting Report” stated that “LED luminaire growth will be driven firstly by tunnel lighting, and then relayed into highway, road, residential and amenity lighting applications starting in 2014.” 1 Our highways are continually becoming more congested. As a result, Provincial and State Departments of Transportation (DOTs) are constantly looking for innovative ways to improve traffic flow. One way DOTs are now helping to ease congestion is by expanding the use of tunnels and long underpasses in large interchange reconstruction projects. With less available right-of-way to work with, and the high costs of maintaining elevated bridge structures over the years, it often makes more sense to “go under” (rather than over) the traffic congestion points. With the addition of these new tunnels and long underpasses comes the issue of proper illumination within these structures, for a safe and efficient driving task. DOTs use recommended lighting practices and guidelines for highway lighting, which include specific criteria for tunnels, set by either the Illuminating Engineering Society of North America (IESNA) or the American Association of State Highway and Transportation Officials (AASHTO). However, both IESNA and AASHTO point out that these recommended practices and guidelines are not a mandate, and DOTs are free to make their own decisions about lighting criteria. Accordingly, effectively illuminating tunnels is often times a challenge. This paper will examine the key considerations of the tunnel lighting application in generalas well as what LEDs now bring to the table and how, accordingly, traditional lighting technologies will be phased out in the future illumination of tunnels."

Jan 1, 2016

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators' results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI's Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995