Search Documents

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By John A. Mathews

It is a great honor to be asked by the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe was of brief duration—only one year—and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher— Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "aus-tenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I worked side by side with William Campbell

Jan 1, 1925

By H. M. Chance

Jan 1, 1886

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982

By Joseph A. Dos Santos

The largest TBM (Tunnel Boring Machine) tunnels are typically along modest slopes, but not always. Occasionally high slope angles are required beyond the capabilities of conventional open trough trailing conveyors. A 2019 project required a large TBM to ascend to an incline angle of 25°. A Sandwich Belt high angle conveyor could easily solve the high angle conveying problem but such a system must include all of the features of the conventional trailing conveyor, particularly the ability to extend with the TBM advance. The writer responded to the challenge and developed a TBM trailing Sandwich Belt high angle conveyor with all of the needed features. The invention (U.S.A. patents awarded October, 2021 and November, 2022) however goes beyond the 2019 project requirements and extends to any high angle incline. This writing first presents the broad Sandwich Belt high angle conveyor development, then its use in various construction and tunneling projects prior to this TBM Sandwich Belt trailing conveyor invention. Finally we present the new TBM Trailing Sandwich Belt high angle conveyor with all of its features and implications.

Jun 13, 2023

By J Nixon

I have to say that my story is not too much different to many others who grew up and worked in the great mining fields like Broken Hill, Mt Isa, Rosebery, Kalgoorlie or Kambalda and any one of them could have stood up here and spun you a good yarn.What does my paper offer you in this volume? By sharing my experiences I want to encourage you to consider your own experience with leadership, taking on change, learning from and contributing to the development of others.I have been very fortunate to be part of many new innovations into underground mining over the past 40 or so years; most of it with Conzinc Rio Tinto Australia (CRA)/Rio Tinto operations.•From hand-held drills and a homemade single boom Jumbo mounted on an old Airtrak, to the sophisticated twin boom jumbos with high speed drifters all controlled by an on-board computer;•from a Scraper winch and a Wagner 2D loader to fully automated electric LHDs that navigate to the tipple, empty the bucket and return to where they come from;•from hand-held cut-and-fill and timber stoping in Broken Hill to the bulk mining methods of a block cave where at Northparkes we mined more ore in a month than we mined in the total five years of operations at Currawang;•from hand-held scaling and bolting with no skin protection to installing ground support with Jumbos and sophisticated Cable Bolters and the introduction of in cycle shotcrete;•from hand-held ladder rising and shaft sinking to Box Hole rigs, Raise Bore Machines and Blind Hole shaft sinking; and•from Gelignite based AN60 stick explosives, ANFO, fuse firing and half second detonators to Powergel, Emulsions and electronic computer programmed detonators that can somehow be initiated by ‘Blast Ped’ travelling through the rock.

Mar 21, 2011

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

By Philip B. Grote

The deep ocean mining industry is in a pre-commercialization stage of development. In the context of a proper legal/regulatory regime, deep ocean mining system design, site survey, and operation technologies are capable of rapid evolution. The report recommends that the regulatory framework develop in parallel with the industry and presents a rationale for implementing this approach. The Government has several interests in deep ocean mining technology: (1) as a potential regulator, sound regulations should be based on an understanding of the technology; (2) as a potential monitor, survey technologies are relevant; and (3) as an estimator of strategic minerals supplies, it is important to understand the technology which allows economic access to deep ocean minerals. Thus, the major portion of the report presents an in-depth review of systems design, operations, and survey equipment and techniques.

Jan 1, 1979

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By J. Cooperman

THE INVESTIGATION was carried out in three stages, depending on the objectives of the work and the kind of equipment used. The first stage involved testing of 11 representative Alabama coals, the source of which is given in table 1. The objective was to find whether these coals could be gasified raw by the Lurgi method, and the equipment used was a 4-inch batch generator (to be described later). This generator proved too small and difficult to control to provide adequate amounts of products under continuous operating conditions for testing. For the second stage, a 6-inch batch generator was used, which was provided with facilities for superheating the steam-oxygen mixture and for synthesizing additional methane from the residual carbon monoxide and hydrogen in the primary Lurgi gas. Selected Alabama coals, Pittsburgh-bed coal from West Virginia, "Disco," and anthracite were used. For the third stage of the work, a continuous generator of 1 square foot grate area, following closely the design of the industrial generators operated in Germany, was provided. This generator was designed by 0. Hubmann, engineer for the Lurgi company, and was expected to give results closely simulating industrial-scale apparatus. The purpose of this equipment was to test prepared materials shown to operate smoothly in the 6-inch generator under conditions approximating as nearly as possible those prevailing in industrial practice. Work of the first stage showed that Alabama coals could not be used in the Lurgi process without first destroying the coking power.

Jan 1, 1951

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration&apos;s proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington&apos;s coal-bearing regions lie west of the Cascade Mountains. The state&apos;s coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation&apos;s total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state&apos;s economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington&apos;s industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining&apos;s Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992