Search Documents

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By J. Luo

A major design problem for upper seam longwall gate roads that are to be constructed in a multi-seam environment is to predict the effects of stress field changes created by interaction. To quantify these effects, case study data were analyzed to develop empirical stress transfer relationships between seams for both longwall and room and pillar mining. Data analysis showed vertical movement and roof characterization in the upper seam to be controlling factors in damage prediction and, therefore, gate road planning and design. CMRR (Coal Mine Roof Rating) was correlated with the multi-seam roof characterization systems previously used. A WINDOWS-based software package named UGLY (Upperseam Gateroad Longwall Stability) was developed. Results from selected case studies were correlated with upper seam stress predictions.

Jan 1, 1997

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

By Downs M

The use of a cutting machine designed to allow simultaneous cutting and setting of roof supports has numerous advantages few development roads in coalmines. The use of such a machine with the added ability to cut a curved roof profile is of considerable interest for longwall development in thick coal.

Jan 1, 1998

By Gregory Hendon

Jim Walter Resources, Inc. (JWR), has successfully longwall mined for many years at depths ranging from 1200'-2500'. However, full pillar extraction has proven difficult and generally economically unfeasible. Overburden and redistributed stresses at these depths require relatively large pillars, which become unmanageable with most pillar extraction practices. The economic benefits of taking gateroad pillars as part of a longwall face have been recognized for some time, including increased life of mine recovery, elimination of belt moves, reduced overcast requirements, and improved longwall to continuous miner ratios. Until recently, the associated risks of pulling pillars prevented any extensive use of this concept at JWR. Due to geological, economic, and longwall repeatability problems, JWR accepted the risks, and undertook pillar extractions with longwall faces in several different applications. The applications included taking a stable pillar (250' wide) as a longwall panel, taking yield pillars on the headgate and tailgate of panels, taking yield pillars and stable pillars in the middle of a panel, mining through chain pillars in the middle of a panel, and taking a support pillar on the tailgate end of a panel. This paper describes the background and experience of pillar extraction with longwalls at JWR.

Jan 1, 1998

By Stanislaw Prusek

The present state of Czech and Polish coal mining industry is presented at the beginning of the article. This paper will inform the reader of the general data concerning hard coal reserves? number of mines, number of miners, output, number of longwalls, productivity, depth of extraction, and extraction methods?in both countries. The main part of the paper describes the methods of gateroad development as well as gateroad support characteristics (support types, gateroad shape and dimensions, distance between support sets, types of reinforcements). The development prospects of gateroad support in the Czech and Polish coal mining industry are also presented.

Jan 1, 2011

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Alcy Dias Rodrigues

O Centro de Operações do Sistema Elétrico da Aperam South América possui um sistema de automação chamado SAE (Sistema de Automação de Energia) para realizar a distribuição e operacionalização da Energia Elétrica na planta em Timóteo, sistema este com mais de 20 anos de implantação. Devido ao alto grau de obsolescência do sistema SAE, a dificuldade de se atualizar todos os componentes do sistema e a complexidade e dificuldade do acesso aos dados, verificou-se a necessidade de encontrar uma forma de disponibilizar os mesmos para os demais sistemas da empresa. Com base nestas necessidades, foi desenvolvido e implantado um GATEWAY capaz de realizar a comunicação com todas UTR’s CORTEX (remotas do sistema), através do protocolo CONITEL 2020, disponibilizando estas informações coletadas em uma camada OPC SERVER para que o sistema PIMS (Sistema de Gerenciamento de Informação da Planta) realize a coleta e armazenamento destas informações, permitindo assim um melhor gerenciamento de energia pelo VIRIDIS (Sistema de Gestão da Eficiência Energética utilizado na APERAM), além de permitir que toda a planta tenha acesso em tempo real às informações de tensão e corrente de todo setor de 13,8 kV, 69 kV e 230 kV.

Oct 30, 2017

By Drew Bazil, David Smith, Matteo Ferrucci, David Pittman

The Gateway program will provide additional rail capacity between New Jersey and Manhattan. This paper describes how a 70-foot-deep section of cut and cover tunnel was designed to directly support future high-rise towers. The tunnel will link previously completed tunnel sections under Hudson Yards to future tunnels under the Hudson River. The design aims to minimize constraints on future overbuild and future tunnels, while maximizing constructability within a small worksite. The tunnel will pass under the High Line elevated walkway, next to an active rail yard, and close to a subway tunnel. The design was developed by a tri-venture of WSP, STV and AECOM. WSP led the design of major underground works; STV designed utility relocations and the underpinning concept for the High Line; and AECOM designed temporary in-tunnel systems. Construction is expected to start in 2023.

Jun 13, 2023

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By M. E. Wadsworth

"For his creative efforts in explaining the electrochemistry of sulfide mineral leaching systems." Leaching reactions that occur during the dissolution of selected base metal sulfides and metals are considered in terms of surface reactions and the influence of intermediate or final products formed. These products may be solid layers, requiring solid phase diffusion for the reaction to proceed, or ions in solution that can influence the kinetics by controlling the mixed potential of the solid. Three general types of reactions are proposed to explain observed rates of reaction. Examples are presented for non-oxidative and oxidative leaching of galena (PbS), anodic dissolution and oxidative leaching of molybdenite (MoS2) and cyanidation of silver and gold.

Jan 1, 1986

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997

By A. W. Hamilton

If you don't know a gauss from a grasshopper, you may be better off than you, think, particularly if you're an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By Ron Tluczek

[Power Point Presentation]

Jan 1, 2006

By Chris Roper

The Gavia Autonomous Underwater Vehicle is a two-man portable AUV that is capable of performing seafloor surveys in water depths to 2000 meters. The standard survey sensor suite includes a dual frequency side scan sonar and high resolution digital camera. Additional survey sensors are currently being incorporated into the Gavia AUV, include Sub Bottom sonar, Swath Bathymetry sonar and Multi Beam sonar. The modular design of the Gavia AUV allows the end user to quickly incorporate new sensors including client developed propriety sensors.

Jan 1, 2005

By R. W. Raymond

(Chattanooga Meeting, October, 1908.) THE immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages-in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted ; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, we Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley's process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. WHAT DID MR. GAYLEY INVENT Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley's first patents. It may be admitted, without such critical analysis, that the possi-

Jan 1, 1909

By Kenneth B. DeGraaf

The development of precious metal recovery processes using chloride systems has mostly evolved from the development of chloride based treatments for base metal concentrates or ores. The recovery of silver from chloride solutions within a process designed for the treatment of base metals usually is part of a solution purification stage. This paper discusses the development of the silver recovery stage used in the GCM HydroCopper process.

Jan 1, 1990