Search Documents

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By Lindsey Schneider, Steve Kirk, Michael Miglioretti, Jeffrey P. Kolzow, Kyle White

The US17 Spring/Fishburne Drainage Improvements Project utilizes a stormwater conveyance tunnel system of approximately 8,250 LF. The tunnel system includes two intersecting tunnels of differing diameter at a 40-degree angle. The intersection was constructed in soft-ground conditions. This paper discusses the design, geotechnical concerns, initial ground support, and final lining construction. The tunnels utilized two soft-ground TBMs excavated at 15 ft and 11 ft with ribs & lagging initial support. The final lining consisted of unreinforced and reinforced cast-in-place concrete with polymer fibers. Concrete final lining was successfully completed in March 2020.

Jun 13, 2021

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By A L. de Ambrosis, S J. Clarke, R Bertuzzi, J Redelinghuys

The M2 Upgrade Project involved widening 15 km of the existing M2 Motorway, which is a key route in Sydney’s road network. The Norfolk Twin Tunnels in North Epping convey traffic over a 460 m length of the motorway. The project involved widening the twin tunnels to provide a third lane and breakdown lane in each direction.The widening of the tunnels was fundamentally different to other ‘greenfield’ tunnel projects in that the operation of the tunnel was maintained throughout construction, with motorway traffic permitted close to the excavation faces on a daily basis. The widened works had to integrate with the existing tunnel support, construction details, and mechanical and electrical infrastructure.The existing tunnel afforded the opportunity to review existing ground conditions in the tunnel. Exposures were mapped within the tunnel, and key design parameters were back-analysed from the original monitoring data to provide increased confidence in the assessed impact from the widening works.Traffic capacity of the tunnels was maintained by detailed staging of the works, and included the ability to reopen the tunnels at short notice.A permit to tunnel system was developed to manage the risks associated with re-opening the tunnel to traffic. A comprehensive suite of instrumentation was maintained to provide reliable monitoring data to support this process. Emphasis on the robustness and reliability of tunnel instrumentation provided increased confidence in the adequacy of the tunnel support being installed. The monitoring was routinely compared with design predictions to check the adequacy of the support measures being installed and confirm the design.The approaches and methodologies developed for the widening of the Norfolk Tunnels were effective in maintaining the safe operation of the tunnels throughout the two years of construction, and provide a framework for increasing the capacity of existing tunnel infrastructure in the future.CITATION:Clarke, S J, de Ambrosis, A L, Bertuzzi, R and Redelinghuys, J, 2014. Design and construction for the widening of the M2 Norfolk Twin Tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 591–602 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Keith Jones, Martin Knights, Timothy Watson

In 1996 a KBR (Brown and Root) led international JV was appointed to design and supervise an underground and surface package. The design of 6 km of tunnels, plus enlargements, deep shafts in glacial and sandstone deposits for the conversion of the existing LEP underground laboratory at CERN, Geneva adjacent to the Jura Mountains/Lake Geneva had to be undertaken in an operational environment and in conjunction with other underground constructions associated with the US$3bn refurbishment.

Jan 1, 2003

By R. C. Gilmore, J. McMack, G. E. Bogin, J. F. Brune, C. DeRosa

"Researchers at the Colorado School of Mines are designing and building a 1:40 scaled physical model of a fully operational longwall coal mine. The purpose of the model is to minimize the occurrence of methane explosion hazards by testing various ventilation strategies and determining optimal methane sensor placement throughout the longwall face. Fluid scaling factors were analyzed using Computational Fluid Dynamics software Ansys FLUENT™ at both full and 1/40th scales. Researchers were able to identify key scaling factors and subsequently developed suitable flow parameters that would maintain full scale accuracy of flow patterns in the 1/40th model. KEYWORDS Coal, Longwall, Methane, Explosion, Scale Model, Ventilation, Fluid Dynamics, Richardson, Gob, Porous INTRODUCTION Mine ventilation systems are a key component for ensuring a safe working environment by introducing fresh air from the surface and diluting explosive gases and hazardous contaminants. This holds true for longwall coal mines where the emission of flammable methane gas from the longwall face as well as the gob can create explosive mixtures of methane and air. Therefore, an effective ventilation strategy can help mitigate the potential for accidents within a mine. Developing an effective mine ventilation system (MVS) requires a detailed understanding of the physics of gas transport and how this relates to specific geometries and obstructions in the face. Researching this phenomenon requires the development of computational fluid dynamics models capable of simulating fluid flow and methane species transport that can be validated through physical experimentation. Unique site conditions determine ventilation layouts for every coal mine. Researchers have designed a 1/40th scaled physical model of a longwall coal face and adjacent gob that includes movable shield supports and a movable shearer with rotating cutter drums that can be adjusted to a variety of ventilation conditions. The proposed work will address the need for an improved Mine-wide Atmospheric Monitoring System (AMS), and provide the ability to link existing MVS models with AMS in real time. By accurately representing the coal face, the gob area and the mining equipment, gate roads and bleeder entries, the scaled model accurately represents all relevant structures, geometry, and dynamic conditions. A Plexiglas cover allows full optical access for sensor equipment as well as visual inspection of the fluid flow and species transport."

Jan 1, 2019

By C. W. Nelson, A. G. Moody

This paper describes the design, equipment selection and onshore fabrication of the largest facilities module ever installed in a single lift in the Gulf of Mexico. Measuring 35.5 x 70.1 x 21.3 m (110 x 230 x 70 ft), the three operating level structure houses Frasch process sulfur mining equipment and weighed nearly 49 million N (5500 tons) during lift. An operating weight of over 74 million N (8300 st) combines with bridge reactions acting on the in-place module and results in a total operating vertical load on the supporting platform deck of about 107 million N (12,000 tons). A Vierendeel truss structural system was selected for framing the module to allow maximum equipment access and routing flexibility for complex, insulated large diameter process piping. Research and finite element analysis of crimp plate siding behavior in shear was carried out during selection of siding type for the module. An interactive design sequence was carried out that incorporated in-place operational criteria, onshore fabrication considerations, complex process equipment requirements, plus load-out, ocean transport and offshore lift analyses. Project schedule dictated that design, procurement and fabrication be fast-tracked with parallel activities accelerated to the maximum extent possible. Design and construction of this largest and most complex module was done concurrently with 52 other components of the project including jackets, decks, process and living quarters modules as well as two 122 x 22 m (400 x 72 ft) sulfur tankers. Total tonnage of steel structures for the project exceeded 90.7 kt (100,000 st). The 5 kt (5500 st) mining module proved the viability and costeffectiveness of larger modules than commonly used in Gulf of Mexico waters. This technical advance can be matched with economic opportunity for other large-scale offshore installations.

Jan 1, 1994

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By F. Djahanguiri

The US Bureau of Mines con¬ducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1997

By Steven L. Anderson

A cut-off wall has been designed and is currently under construction along the Back Dam of the existing tailings impoundment at Red Dog Mine, Alaska. The cut-off wall, which will be in the order of 5,000 ft long and up to 150 ft deep, when complete, is being excavated using a 40 metric ton Bauer trench cutter head mounted on a Liebherr crawler crane, in combination with a closed loop slurry pumping and de-sanding system. The tailings impoundment is situated in an area of warm permafrost and high potential seismic activity. Design incorporated an assessment of rock jointing to define the final depth of the wall along the alignment requiring the use of plastic concrete backfill to address the concerns associated with potential cracking of the wall due to settlement and during seismic activity. The results of the geotechnical investigation program, particularly with respect to variation in rock hardness along the wall alignment are discussed, as are the design criteria for the plastic concrete backfill, the challenges faced during construction, including scheduling of the work with the on-going dam raise activities of the mine, and the lessons learned with respect to potential productivities and selection of cutter wheels and teeth. Also described are the requirements for and advantages of utilizing a slurry boosting system to meet pumping requirements, re-design of the plastic concrete mix to consider workability and optimization of cutter teeth configurations to reduce wear through highly varied rock hardness.

Jan 1, 2010

By Verya Nasri

This paper will present the design and construction of a deep underground station of the Réseau Express Métropolitain (REM) project; the Édouard Montpetit station. The Édouard-Monpetit station is an interchange station that will connect the deeply sitting REM tracks to the existing metro station of the same name located closer to the surface. Édouard-Montpetit station is expected to be the deepest in North America, surpassing the famous Forest Glen Station. The various challenges and solutions put forth for the successful completion of this underground work are presented to serve as a valuable example for future deep excavation performed in urban area, in the close vicinity of highly sensitive structures.

Jun 13, 2021

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By Jim Bruce

This paper presents details of a slope stabilization scheme built in late 2003 at a 16m-high railway embankment in southern Ontario, Canada. The owner, faced with continuing maintenance and safety issues arising from numerous nuisance slides, and residential neighbors in close proximity to the slope, sought new proposals to replace a previous recommendation to cut down all trees and undertake a deep soil nailing scheme. A non-reticulated micropile array with surface cap beam was proposed and built on the south side of the embankment with no tree removal required. A detailed FLAC analysis was completed, using multiple iterations to arrive at the eventual, optimized micropile depth and spacing. Analysis predicted an 18% increase in the factor of safety. Short term inclinometer monitoring and performance evaluations in the months since construction so far corroborate the prediction.

Jan 1, 2004

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001