Search Documents

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By Victor Phillips

Cyclone thickeners have emerged from the development stage and now can be accepted as useful tools for the recovery of fine coal from a preparation plant circulating water. As primary thickeners in a closed water circuit operation, their advantages over conventional thickening methods are twofold-the lower initial investment and reduced area requirements.

Jan 8, 1951

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column, and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. The results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed.

Jan 1, 2003

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. Results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed in this paper.

Jan 1, 2000

Cyclonic Separation Effect of Metallic Ores in Cyclonic-Static Micro-Bubble Flotation Column

Sep 13, 2010

By X. Zhou

A novel flotation device, cyclonic static micro-bubble column flotation (FCSMC), was introduced in this paper. FCSMC has been widely applied for fine coal preparation in China, and its application has been further expanded to the mineral processing industry. The FCSMC system features a unique cyclonic structure which enhances the separation performance of the column. In this paper, the cyclonic separation mechanism of FCSMC process was investigated, and corresponding kinetics equations were established to probe the separation principle of this device. Some typical examples of using FCSMC to separate different materials including coal, copper, fluorite, etc., were presented. Key words: cyclonic static micro-bubble flotation column, cyclonic separation

Jan 1, 2008

By John L. Watson

The processes of magnetic separation and cyclone classification are common in the mineral processing industry, and frequently the two are found in consecutive stages in the beneficiation of a magnetic mineral ore. The application of a magnetic field across the cyclone, to combine the two stages in treating a magnetic mineral pulp, has been investigated with a view to possible practical applications in the mineral industry The results of this research reveal that magnetic particles can be manipulated within the cyclone body by the application of a magnetic field, and that magnetic grades may be significantly upgraded with recoveries in excess of 90%.

Jan 1, 1983

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973

Once applied, EarthZyme reduces the tendency for a road to exhibit common maintenance issues: wash-boarding, rutting, heaving, potholing and dust.

Aug 1, 2013

By J. E. Nelson, R. J. Bonnis

Recent completion of Cyprus Bagdad's $240-million modernization and expansion program has registered a 700% increase in ore production with only a 50% increase in labor. Elements of this remarkable achievement include the application of large-scale mining equipment as well as the selection of the latest in processing hardware. Most important, however, was the early recognition that Bagdad's labor personnel is its most important asset.

Jan 4, 1978

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By Raymond L. Jones

With the inauguration of open-pit copper mining in Bagdad, Ariz., plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until spring 1961.

Jan 9, 1977

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By Ross R. Bhappu

Anticipating a major power cost increase in 1990, Cyprus Copper Company decided to modernize the Miami Smelter at a cost of $92.5 million. The modernization project included the addition of an Isasmelt vessel for use as the primary copper smelter and the modification of the existing electric furnace to a slaglmatte separating vessel. The project was completed in June of 1992 and is currently operating at close to its design capacity. This paper provides a summary of the decision making process, a description of the project, a summary of start-up problems and solutions and the current status of the smelter operation.

Jan 1, 1994

By Gary W. LaChapelle

Cyprus Miami Mining Corp. has a history of overcoming adversity through innovation and adaptation to changing conditions. Requirements to remain profitable in the 1990s include a combination of advanced technology, employee involvement and training, attention to customer satisfaction, environmental awareness and quality management. The Miami property is located in the Globe-Miami area of Arizona, 130 km (80 miles) east of Phoenix and 160 km (100 miles) north of Tucson. The complex is located in a high desert environ¬ment at an elevation of 1065 m (3500 ft). The region receives about 480 mm (19 in.) of precipitation annually. History Mineralization at the Miami property was first discovered in the 1880s, which led to underground mining of copper by the 1890s. In 1911, the Inspiration Consolidated Copper Co. was formed by combining the Inspiration and Live Oak Mines. Full-scale production began in 1915. Block caving methods were used at both mines. Open-pit mining commenced in 1948. Underground mining had ceased by 1954, and all production was obtained from surface operations. Innovation has been the key to Miami's success. Development of sulfide flotation and the ferric cure process for vat leaching were advanced at Miami. In situ leaching of oxide material, remaining after block caving had removed the sulfide ore, was also used.

Jan 1, 1993

By J. L. Bruce

AFTER six years of war-enforced idleness, Cyprus copper mines are operating again. This relatively long shutdown seems infinitesimal when compared with something like seventeen hundred years of inactivity that followed the important operations of the ancient Romans, and continued until the twentieth century. The historical records of the ancient operators are scarce but full of interest to those who realize that Cyprus copper production was important more than two thousand years ago. This paper, however, will give only a brief review of the ancient history and the evidence of ancient mining which have been quite fully covered in other publications.1-6 The purpose of this paper is to give a general sketch of the Cyprus Mines Corporation's enterprise in the Island of Cyprus, with special emphasis on those conditions and practices which are unusual. The picture is not intended to be complete, and many interesting details will be omitted. Some of these may be described in subsequent papers covering departmental practices. The principal operations of Cyprus Mines Corp. are in Cyprus, where it has leasehold concessions from the Cyprus Government covering about 50 square miles. It holds additional areas under "Prospecting Permits." The consideration for the concessions is a royalty on production, coupled with minimum annual rentals. Cyprus is a British Colony in the Eastern end of the Mediterranean with an area of about 3000 square miles and a population of about 400,000, of which 65 pct may be classed as Greeks on the basis of language, religious training, and traditions. About 25 pct are Moslems, principally of Turkish extraction. Prevailing languages are Greek and Turkish. A large proportion of the supervisory and administrative staff and practically all of the skilled and unskilled craftsmen and laborers are drawn from the native population. The "overseas" staff constitutes not more than 2 pct of the employees. The majority of these are from the United Kingdom, the British Dominions and Colonies. About one-third are from the United States of America. The topography of the Island is rugged, with mountains and foothills covering more than two-thirds of the area. Between the Kyrenea range rising to 3000-ft elevation, along the north coast, and the Troodos range (maximum elevation 6400 ft) occupying the southwest half of the Island, lies a cultivated rolling plain, the "Mesaoria," dry in summer and watered only by the winter rains and by scanty irrigation from small mountain streams and wells in the spring and summer. Climate and natural vegetation are characteristic of semi-arid conditions. The "urban" population, about one-fourth of the total, lives in the five port towns, Famagusta, Larnaca, Limassol, Paphos and Kyrenia, and in the capitol Nicosia, near the center of the Island. The suburban population lives almost entirely in villages or small towns, with very few people residing in isolated country homes.

Jan 1, 1947

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975