Search Documents

By René Winand

A new process was studied at large laboratory scale at Université Libre de Bruxelles, under contract with Metallurgie Hoboken-Overpelt. A two cathodes (1m long ; 0.2 m high) channel cell was used at 2000 A/m2, with an electrolyte flow rate up to 1.8 m/sec. The main results may be summarized as follows : cathodes are electro¬refined grade in analysis ; metallographic structure and surface roughness are kept under control up to 1.3 cm (one side deposits) ; silver in cathode is controlled by CI and Br ions in solution ; organics must be used at very low concentrations (in the range of 0.1 mg/1, with a consumption of about 0.01 mg/lh).

Jan 1, 1987

By H. Cui

Rapid technological development has caused an increase in the demand for rare earths. Ancylite, a strontium rare earth carbonate, is a potentially significant source of rare earths. In this research paper, essential aspects of the magnetic separation and flotation processes for Bear Lodge ore are presented. A flowsheet is proposed based on an optimization of the variables and flotation simulation. The economic feasibility of the proposed processing operation is analyzed.

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By Theo Lehner

"During my first contact with industrial metallurgy as a summer vacation worker at the Steelplant at Luleå, Sweden, I came during a visit to MEFOS into contact with works of Prof. Worner caried out during the piloting of the Worcra continuous steelmaking process. These tests are still today remarkable as an innovative step in the art of metalmaking. By that they involved the necessary ingredients for the development of our art: seeing, knowing and doing. Industrial injection as applied during slag fuming will be discussed below.Phenomena of injection metallurgyPhenomenon according to Collins dictionary is"" anything that can be perceived as an occurrence or facts by the senses"". To open the senses for the interesting phenomena in pyrometallurgy must be the main task of any educator. The investigations by Engh et al. around the mixing phenomena of the WORCRA process are an early example of combining senses with knowledge. To see what you model must be a crucial part in any development. This can also involve to see and control that one is subject to the same conditions as in published models. Below the need ""to see"" will be illustrated by some recent investigations around slag fuming. In the literature various models for reactions occuring during the fuming of slags are presented. Two recent models hint ·ata) the occurrence and importance of iron for the fuming processb) the occurrence and importance of lead droplets during respectively."

Jan 1, 1996

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By Shi Guan-Yong, Niu Li-Ping, Dou Zhi-He

"In the preset work, the viscosity model (named modified KTH model) proposed by Sichen Du and S. Seetharaman et al and extended by Shu Qi-feng was applied to the ESR slag systems. A correlation to predict the viscosities of CaF 2-(CaO)-Al203 slags using interaction coefficients of different cations in the presence of oz-and viscosity interaction coefficients between oz-and F in the presence of different cations has been developed. The interaction coefficient between oz- and F- in the presence of Al3+ was determined from the experimental data as shown in known literatures. The good agreement between the calculated viscosities and the experimental data in the CaF2-(CaO)-Al203 systems has indicated that this approach can be successfully employed to predict the viscosities of ESR slags.IntroductionReliable viscosities data of high-temperature slag melts are important for the modeling and design of high temperature metallurgical processes. Although a number of experimental measurements have been carried out, the available viscosities data is still scarce compared to the needs of today's technology, especially in the case of complex melts. In process simulations, the needs of viscosity descriptions for complex systems which could enable the extrapolation of the data as functions of temperature and composition is strongly felt today."

Jan 1, 2013

By N. Kanari

The kinetics of oxychlorination of MgO by Cl2+O2 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+O2. C12 and O2 at 950 °C were about 0.65.0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999

By F. Patisson

During exothermic gas-solid reactions, heat generation makes temperature rise and modifies the rate of the various mass transfer processes, namely the chemical reaction itself, the pore diffusion and the external transfer. We have investigated this thermal effect during the oxidation of zinc sulfide porous pellets in a thermo balance furnace, between 550 and 900°C-and under O2-N2 atmosphere. The results have been' analyzed by using, firstly, the law of additive reaction times derived from the isothermal Grainy Pellet Model, and, secondly, a new numerical model taking into account non-isothermal conditions. Both the models can satisfactorily simulate conversion versus time, but the numerical model also depicts the temperature evolution within the pellet. Finally it is shown that owing to the heat generation the zinc sulfide oxidation takes place under diffusion control (3/4 internal, 114 external) in all the cases studied. During the course of reaction, the. pellet undergoes strong temperature variations, with thermal gradients confined to a shell oxide layer.

Jan 1, 1996

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By W. K. Choi

Stainless steel exposed to wet environments at ambient temperature is subject to the formation of a surface biofilm. Depending upon the prevailing environmental conditions (dissolved oxygen, pH, Eh, concentration of cationic/anionic species), the biofilm may stimulate corrosion through formation of differential aeration zones and concentration cells. Corrosion significantly impacts the United States economy, since on a yearly basis, corrosion induced losses are estimated to be over $200 billion. A large portion of this corrosion is imputable to bacterial activity, and basic information is needed for a better understanding and control of the biocorrosion phenomenon. The present study has investigated the influence of Thiobacillus ferrooxidans in the corrosion of American Iron and Steel Institute (AISI) 304, 316 and 416 stainless steel samples. The formation of biofilm and microstructural changes on the surface of stainless steel samples and their weldments were assessed by microscopic examination, and the changes in the mechanical properties by stress-strain measurements. The significance of the results will be discussed.

Jan 1, 1993

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By B. Nowak

For sources with an iron-to-vanadium ratio of far above 1, it is proposed to leach in acid and to oxidize under autoclave conditions. During this oxidation process, it is experimentally shown that divalent iron contained in this solution will be oxidized to trivalent iron, whereas free acid contained will be consumed by this reaction. In case no acid is present or already fully consumed, a solid consisting of ferric compounds and an iron-vanadium-co-precipitate will form that can be filtered from the solution. If choosing the right reaction conditions, this filter cake has an iron-to-vanadium ratio of close to 1, whereas the liquid remainder is almost vanadium free. This precipitate, identified as FeVO4, 1.1 H2O, can be processed by conventional technologies such as caustic leaching, or probably salt roasting or reduction with aluminum, yielding common marketable products.

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013