Search Documents

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By Kazuki Morita

Dissolution mechanism and solubility of chlorine in the oxide melts, such as CaO-SiO2-Al2O3 (-Na2O), Na2O-SiO2-Al2O3 and CaO-SiO2-FeO systems, have been equilibrium technique was employed with controlled Po2 and PCl2, (Po2 = 10-6 -10 19 atm, PCl2 10-6 -10-13 atm at 1673-1748 K). The solubility of chlorine in the 40mass%CaO-40mass%SiO2- 20mass%Al2O3, slag was found to vary in proportion to Pb2/ w and pc/z/p' which proved that chlorine dissolved in the melts as C1 anion. Hence, the chloride capacity (CCI-), indicating the ability of molten oxide to absorb chlorine, has been defined as; The Ccl value was observed to increase with increasing slag basicity and temperature, and showed a reasonable relationship with that Of CS2-. Based on the result obtained in the present study, chlorine distribution during incineration with slags was predicted quantitatively.

Jan 1, 2003

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Kandipati Sreenivasarao

A promising method for removing heavy metal ions from dilute effluents is ion- or precipitate- flotation, in which a suitable collector is added to form hydrophobic metal-collector complexes or compounds that can be collected as foams. We have successfully removed Cu(II), Cd(II), and Pb(ll) from dilute solutions using sodium dodecylsulfate and ethanol as collector and frother respectively. However the process would not be economically viable unless the collector could be recycled, and the heavy metals recovered in a concentrated, preferably marketable, form from the foams. We investigated four different methods to decompose heavy metal-dodecylsulfate complexes, namely precipitation of hydroxides, precipitation of sulfides, chemical stripping, and electrolysis. We compare the performance of these methods. In each case the observed behavior is related to known thermodynamic data, and potential applications are discussed.

Jan 1, 1995

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

Rapidly solidified TiAl-Cr-xNb-Y(x=2,4,6, at.%) alloys have been produced using a single roller melt spinning method. The microstructure of alloy ribbon was refined and component became more homogeneously by rapid solidification technology. There were two phases in alloy ribbons, including -TiAl and 2-Ti3Al phases, yet the amount of 2-Ti3Al phase in matrix obviously increased by rapid solidification than cast alloys. The micro-hardness testing also carried out. Compared to the cast alloys, the alloy ribbons have much higher hardness.

Jan 1, 2009

By V. Ramachandran

Over the past 20 years, water treatment plants have been built at various Asarco facilities to effectively handle the process waste streams that need to be bled from the system. The current paper review the several operations with reference to (a) waste streams processed, (b) process chemistry, (c) discharge options and recovery of treated water, and (d) sludge disposal.

Jan 1, 1994

By Heinz Giegerich

This paper deals with a new development in recycling second generation catalytic converters, namely metal substrate converters (MSC). It describes a patented dismantling process, whereby the MSC is segregated into it's three components outer steel shell, metal substrate carrier foil and ceramic W8shcoat with embedded precious metals.

Jan 1, 1995

By George Kachaniwsky

Until mid-1982 the Mines Gaspe copper smelter consisted of a fluid bed roaster, a reverberatory furnace, two Peirce-Smith converters of which only one was blowing at any one time, anode casting facilities, and a single contact sulphuric acid plant treating both roaster and converter gases. Reduced concentrate supplies have led to the shutdown of the roaster and, as a result, it was necessary to adapt the converter and acid plant operation to the new operating mode: green concentrate smelting with resulting lower matte grades and acid plant treatment of off-gases from only one blowing converter. Therefore, modifications were carried out to existing equipment and methods of operation and control. This paper describes the result of work done to obtain steady, maximum strength, converter off-gas flow and an efficient acid plant operation. Topics covered include: optimization of converter operation, tightness of hood and off-gas ducting, improvements in acid plant/converter communications and modifications of acid plant operation and control to cope with the fluctuations in converter gas flowrates and strengths.

Jan 1, 1983

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Shengqin Zhang, Jagannath Pal, Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

The kinetics of magnetite reduction with mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This new process bypasses the cokemaking and pelletization or sintering steps required for the blast furnace. The particle kinetics were studied using magnetite concentrate particles of different sizes. Reduction degree of 60% was achieved in a few seconds in at 1350 oC using CO reductant alone and over 90% when H2 + CO gas mixture was used. The effects of reductant partial pressures, temperature, and particle size on the reduction kinetics were studied.

Jan 1, 2016

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Yang Cui

The partition ratios of lead and antimony between liquid copper and MgO saturated Cu2O-CaO-SiO2 flux and their removal rate by using CuCl-based flux were measured between 1423 K and 1573 K. For Cu2O-CaO-MgOsatd. system, the partition ratio of Pb was not affected by the CaO content at 1573 K, while that of Sb increased with increasing CaO content. The maximum value was 160 at the CaO content of 15.4 mass%. For Cu2O-CaO-SiO2-MgOsatd. system, two liquid phases of calcium silicate rich phase and Cu2O rich phase were observed at 1573 K. The partition ratios of Pb and Sb between calcium silicate phase and liquid copper depended on the (mass%CaO)/(mass%SiO2) ratio. When the (mass%CaO)/(mass%SiO2) ratio increased, the partition ratio of Pb decreased and that of Sb increased. For CuCl flux, the removal of Pb from liquid copper at 1473 K was possible, and a relatively low concentration could be reached. Moreover, most of lead as metal chloride vaporized from flux. For the removal of antimony from liquid copper at 1423 K, it was difficult by CuCl flux, and the removal ratio was approximately 20% for 75 minutes. However, the addition of CaO or Na2CO3 to CuCl flux was relatively effective to remove antimony, and the concentration of antimony reached a relatively low value after 15 minutes by using CuCl-CaO or CuCl-Na2CO3fluxes. Moreover, a small part of antimony as chloride vaporized from flux.

Jan 1, 2006

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Raj P. Singh

Lewatit TP207, a chelating resin with iminodiacetate functional group, is used for the purification of cobalt hexammine chloride solution for divalent cationic impurities (US Patent No. 5,154,757). The method is employed at commercial scale in OSRAM SYLVANIA Inc. cobalt chemical production since 1992. It is observed that after long use in the purification of cobalt hexammine chloride solution, a large number of resin beads tum black from their original beige color. The purpose of this paper was to characterize these black-colored resin beads for their ion exchange behavior. The resin sample used in this work was an exhausted production TP207 resin containing large number of black-colored beads. The results indicated that blackened resin beads can be regenerated to almost full capacity and' their ion exchange behavior for the purification of cobalt hexammine chloride solution was comparable to the new resin.

Jan 1, 2001

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By Lijun Liu, Yingwei Li, Jianhua Liu, Jinhui Peng

"As essential equipment in the metallurgical industry, current air heat exchangers cannot meet the requirements of high temperature heat transfer. In this paper, an energy efficient air heat exchanger, based on accumulation of the heat generated by microwave absorbing materials, is presented according to heat transfer theory and principles of the microwave field. A tubular shaped heat exchanger was designed and built up through temperature-rising curve, and experimental research of microwave high-temperature air heat exchangers was carried out. It was found from experiments that the tubular shaped heat exchanger fabricated using material B could be used for high temperature heat transfer system, and equilibrium temperatures could reach up to 457—485?.IntroductionHeating or cooling of air by heat exchangers is commonly practiced in a wide range of industries including construction, chemical, machinery, textile, printing, and dyeing [1-3]. Generally such heating or cooling of air is achieved in pipe heat exchangers. There are several drawbacks for such heat exchangers, namely, (i) the limitation of temperature to which the pipes can be heated, (ii) tendency to oxidize at high temperature, and (iii) poor strength of metallic pipes at high temperature. These limitations do not allow pipe heat exchangers to be operated at high temperatures [4-6].Microwave heating of inert solids, which are stable at high temperature, is a possible solution to achieve high temperature of the medium in air heat exchangers. It is well-known that microwave heating is an efficient, clean, safe, easy-to-control heating method. Microwave heating utilizes the dielectric and magnetic properties of a material. When microwaves penetrate and spread into the dielectric material, electrons, ions, etc move in the internal electromagnetic field, while the elasticity of inertia and friction impede these movements. This results in a significant thermal effect, increasing the surface temperature rapidly [7-8]. This paper studies mainly design and experimental research of microwave high-temperature air heat exchanger."

Jan 1, 2011

By J. G. Reid

Nickel is second only to aluminium, of all non-ferrous metals, in energy required to convert the ore to metal. Nickel Laterite ores, which constitute the feed source for approximately 40% of world nickel production, are at a particular disadvantage because of the absence of sulphur, as an energy source, in the ore and because lateritic ores general 1 y are not amenable to beneficiation. The dramatic escalation of oil prices which commenced in 1973 and continued for a decade meant that Nickel Laterite refineries using oil as a primary energy source were placed at a distinct disadvantage relative to refineries utilizing nickel sulphide concentrate feeds. By the late 1970's the continuing large difference in oil and coal prices caused Greenvale to consider converting certain high oil consuming areas of the refinery to coal. These investigations confirmed that the areas of ore drying and power generation, which together consumed 50% of total Plant oil requirements, could be economically converted from oil to coal firing. Construction of the coal conversion facilities commenced in October 1980 and the first ore drying air heater came on line in August 1981. Construction was completed with the commissioning of the coal fired boiler in June 1982. This paper outlines the additions required to receive and utilize coal in ore drying and power generation and how the changeover was completed with minimal process disruption.

Jan 1, 1988