Search Documents

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By M. Oliazadeh

The present study was performed to develop a process for solvent extraction of molybdenum and cobalt from an acidic solution generated by an electrodeposition process of nanocrystalline cobalt alloys. Solvent extraction is a common practice in hydrometallurgical and refining processes to produce metals; however its application for separation of molybdenum and cobalt from this specific solution is new, because molybdenum and cobalt are not commonly associated together in nature. Five commercial organic extractants were examined for extraction of cobalt and molybdenum from synthetic acidic solutions with pH ranging from 1 to 5. Preliminary results showed that at pH 2, any of the Cyanex 923, Alamine 336, Aliquat 336 and Hostarex A327 could be used to extract 99% of molybdenum from solutions, while from pH 3 to 5, Aliquat 336 was able to extract about 100% of molybdenum. Cobalt extraction, on the other hand, varied from 15% to 23% at pH 3 and 30% to 53% at pH 2 using different extractants. Based on results obtained, Aliquat 336 was applied on mixed solutions of cobalt and molybdenum at various pHs. The results showed that molybdenum could be extracted as much as 99% from a mixture of molybdenum and cobalt at acidic pHs, while less than 1% of cobalt was separated at pH 2 to 4 simultaneously.

Jan 1, 2003

By Jose Castro

The growing demand of scrap to supply the electric arc furnace has driven to search for new alternatives of raw material. The DRI produced using self-reducing pellets has become competitive due to the potential use of a wide range of carbonaceous materials such as coal, charcoal, biomass etc. In this context, the rotary kiln process using improved technologies such as post-combustion and self-reducing burden is a promising source of high quality raw materials. This paper presents a mathematical model of the rotary kiln process designed for self-reducing pellets and post-combustion. The model is based on the transport equation of two-phase flow, energy and mass transfer. The solid material is composed of a typical self-reducing pellet. The model considers the solid phase (C, volatiles, Fe2O3, Fe3O4, FeO, Fe, H2O, SiO2, Al2O3, MgO, P2O5, K2O, Na2O, FeS, CaO and gangue) and the gas phase (N2, O2, CO, CO2, H2, H2O, SO, SO2 and SiO). For each of the above components a conservation equation is solved and the mass and energy transport is accounted. The set of differential equations are coupled by the rate equations describing the kinetics of the several reactions, which take place within the rotary kiln. All the conservation equations are solved based on the finite volume method applied for a three-dimensional cylindrical coordinate system. Simulation results are presented for global parameters such as metallization degree, productivity, gas utilization ratio and calorific value. Inner conditions such as three-dimensional gas and solid temperature patter and compositions are discussed.

Jan 1, 2006

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By B. Zeytuncu, O. Yucel, O. H. Celik, M. H. Morcali

"The Taguchi method was used as the experimental design to determine the optimum conditions of cementation behavior of the ruthenium chloride solution. Cementation was carried out using metallic zinc powder. The experimental conditions were studied in the range of 25-45°C for reaction temperature (A), 30--60 min for reaction time (B), 0.5-1.5 for pH of solution (C), and 30--50 mg for zinc powder (D). Experimental parameters and their levels were determined in the light of preliminary tests. Orthogonal array (OA) L9(34) consisting of four parameters each with three levels, was chosen. The optimal conditions found for ruthenium, such as a reaction temperature, reaction time, pH of the solution and mass of zinc, are respectively: 45°C, 45 min, 1.5 and 50 mg. Under these conditions, the ruthenium cementation efficiency obtained by theoretically and experimentally was in good agreement, which were 99.8% and 99.7% respectively."

Jan 1, 2013

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By Marc Verhaege

The effluent under investigation results from a catalic oxidation unit in which paraxylene is oxydised to terephtalic acid. The solution contains cobalt and manganese as their acetates in a concentration range of 0,4 - 1,2 g/I of cobalt and 0,8 - 2,4 g/l of manganese. Before being fed into the main waste stream treatment unit of the plant it is advisable to apply a petreatment step in which both metals are eliminated to a great extent from this effluent. Conventional treatment is done by precipitation of both metals either through pH increment with a base or by adding a suitable reagent producing insoluble species. The aim of this study was to look for a treatment (elimination of both metal species) in which no sludge or precipitate is formed.

Jan 1, 1995

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Xi Dai

The LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode materials for Li-ion battery were synthesized with Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) as Fe sources by high temperature solid-state reaction method. The Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) materials were produced by liquid co-precipitation method and crystal structure and morphology of cathode materials were characterized by X-ray diffraction and scanning electron microscopy. The composition contents and charge-discharge performances were measured by chemistry analysis and charge-discharge apparatus. The XRD patterns showed that LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode material samples were well-crystallized homogeneous olivine-type phase, with only tiny trivalent iron impurities according to chemistry analysis results. Charge-discharge test showed that cathode materials possessed excellent charge/discharge capacities, about 150mAh/g at 0.1C rate and more than 120mAh/g at 0.4C rate. The polarization of cathode in charge-discharge process can be restrained effectively, for the potential offset between oxidative peak and reductive peak of doped LiFePO4 material was only 0.079V, lower than pure LiFePO4 markedly.

Jan 1, 2006

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours&apos; test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By I. G. L. Sinclair

The Selbaie deposit is located in northern Quebec. It is comprised of three distinct, but genetically related, Cu-Zn-Ag ore bodies which also contain economically significant amounts of Au. The deposits are Archean in age and volcanogenic in origin. At Selbaie, ore microscopy has been employed to aid in planning of ore beneficiation methods and to monitor the ongoing performance of the concentrator. Examples of both types of study are described. Early in the life of the mine, excessive amounts of Zn appearing were found to be appearing in the Cu concentrate. Microscopic examination of concentrates showed that this was being caused by the presence of coatings of supergene chalcocite on sphalerite grains. Fine coatings of supergene galena and chalcopyrite were also observed on some sphalerite grains. The presence of Ag and Au in the ores makes an important contribution to the revenue of the mine. The various modes of occurrence and mineralogical relationship of these two metals are described and discussed. Monitoring of the ongoing concentrating process at selbaie is done by qua-litative and quantitative examination of products collected at various points along the circuit. Causes of such problems as excessive loss of metals to the tailings or inefficient recovery of individual metals, can often be identified and possible solutions proposed.

Jan 1, 1989

By Jeffrey R. Taylor

The distribution of low concentrations of Cr, Mn, Rh, Co, Ni, Ag and Fe between copper matte and bullion phases has been measured at 1200oC. These results. together with values for nine other elements, have been used to develop a simple model to describe the distributions in terms of known thermodynamic properties?. The Temkin model for ionic melts was assumed to apply to the sulphide species in the Cu-S matte? phase and it is shown that the choice of sulphide species is particularly important for successful representation of the experimental .results?. In general, the lowest sulphlde (minimum sulphur :. metal ratio)? formed by the. metal is most suitable, although Ni, Co, Rh and Pd appear to associate with more sulphur in the melt than suggested by the? composition of their lowest sulphide. A correlation between the composition of the metal sulphide species formed in the ternary system and the? position of the minimum in the free energy of mixing curve in the metal-sulphur binary -system is? proposed.

Jan 1, 1983

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By Hong N. Vu, Jitka Jandova

"Gypsum and limestone methods were examined in this study to process zinnwaldite wastes originating from dressing Sn-W ores mined in the Czech Republic. These wastes containing 0.20-0.30% Li and 0.10-0.20% Rb were subjected to magnetic separation to obtain a zinnwaldite concentrate with 1.36% Li and 0.94% Rb. It was observed that processing of the zinnwaldite concentrate with gypsum resulted in almost 96% recovery of Li into aqueous liquors, whilst rubidium extraction was only 25%. At the same time, it is possible to extract almost 92% Li and Rb from the identical zinnwaldite concentrate if the concentrate is processed by limestone method. Lithium carbonate, a final product of both methods was recovered from the refined sulphate solution using K2CO3 as a precipitation agent and/or from unrefined hydroxide solution using gaseous CO2. In the continuation of this study, rubidium will be separated from carbonate solutions after Li2CO3 precipitation as RbAl(SO4)2, an intermediate for Rb2CO3 production. IntroductionLithium is used as an alloying constituent in lightweight alloys, as a heat transfer medium in nuclear reactors and as a component in primary and secondary batteries. With the development of a new generation of electric vehicles, the lithium demand will dramatically grow. Lithium chemicals find extensive application in many industrial branches such as metallurgical, glass, ceramic and pharmaceutical industries. Rubidium compounds are predominantly used in psychiatry and medicine, in magneto-optic modulators, solid-state lasers, phosphors and components of electrolytes for fuel cells. The four most important lithium minerals are amblygonite, spodumene, petalite, and lepidolite. Spodumene LiAlSi2O6 (6.0-7.5% Li2O) and petalite LiAlSi4O10 (3.5-4.5% Li2O) belong to aluminosilcate minerals. Lepidolite (Li.Al)3(Al.Si)4O10(F.OH)2 (3.30-7.74% Li2O), lithium mica, is the most important representative of the mica minerals, a subgroup of the aluminosilicates. It frequently contains 3–5% Rb2O and eventually caesium. Zinnwaldite, which has the general formula K(Li.Al.Fe)3(Al.Si)4O10(F.OH)2 (2-5% Li2O), is regarded as a variety of lepidolite with a high iron content. Commercial amblygonite is a complex phosphate (Li.Na)Al(F.OH)PO4 (up to 9.88% Li2O), however, its deposits have not been commercially exploited because of their small size. Natural brines with a high lithium chloride content are important in the industrial production of lithium [l]"

Jan 1, 2008

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.