Search Documents

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

By Victor V. Nazimko

Long term stability of the pillars that have been remained after R&P extraction causes postponed subsidence. To prevent unforeseen subsidence and to diminish postponed subsidence 25-50% new method for its control has been developed by the author. It supposes to use drilling and blasting technology and other original approaches. New method has been fulfilled through the holes being drilled from the surface or from the active underground openings. Explosives had been charged into the holes and were blasted. This had increased bulking factor dramatically and prevented natural caving of the strata. Physical scale modeling corroborated efficiency of the new approach. The bulking factor has grown from 0.0623 to 0.1185 and surface subsidence has been diminished from 1.1 m to 0.2 m or 5.5 times.

Jan 1, 1996

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By Kelvin K. Wu

A coal waste disposal dam failed on Buffalo Creek near Saunders, West Virginia, on February 26, 1972. This accident resulted in the loss of 125 lives, left over 4000 people homeless, and resulted in millions of dollars in damage to several downstream communities. As a result of this tragic event, major changes occurred in the mine waste disposal practices used by the U.S. coal industry. This paper summarizes changes in U.S. coal-waste disposal practices in the nearly 35 years since the Buffalo Creek dam failure and identifies safety issues that need to be addressed for continued improvement. While many organizations and individuals have played roles in the improvements that have occurred, this paper focuses on the role played by MSHA and its predecessor agencies.

Jan 1, 2006

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Haile Manteqi

In longwall coal mines, estimation of roof strata condition, sequence of loading, and supporting requirements are of a high degree of importance, and they are directly related to production and safety. Also, a prediction of the initial caving distance is rather complicated to calculate, because there are many parameters that effect caving process?roof and floor strata conditions, thickness of immediate roof, depth of cover, excavation geometry, and magnitude, and direction of principal stresses. This paper presents the results of 3D numerical modeling of the initial caving mechanism using the finite difference code FLAC3D at the E1 longwall panel of the Parvade 1 underground mine located in the Tabas area in the central part of Iran. The initial caving distance obtained was 10.4 m. Also, the results of numerical modeling have been compared to the analytical methods, such as Peng?s method. The results show good agreement with each other.

Jan 1, 2012