Search Documents

By Zuoliang Xiu

Experience indicates that rockbolting is the most efficient and cost effective means of supporting gateroads of retreating longwalls. However, gateroads supported solely by rockboltiug currently accounts for less than 16% of the 4500km of annual gatemad drivage in China According to a stated target of the Ministry of Coal Industry, this percentage should be at least 50% by the year 2000. Since the learning stage of the technology which is indicated by low drivage rates and frequent roof falls in rockbolted gateroads must be overcome , strategies for the application of rockbolting to gateroads have become the focus of discussions on this topic. This pap presents the recent development on longwall gateroad rockbolting technology in China The development work has concentrated on understanding the mechanism of rockbolting; establishing new design procedures of bolting parameters fix gateroad support upgrading the consumable; optimizing bolt installation procedures; adopting better roofbolting machines; and developing adequate secondary reinforcement technique. The authors believe that this development work together with the on-going wok in other aspects of gaterosd rockbolting, as discussed in this paper 9 represent the rational strategies for the application of rockbolting technology to a wider range of longwall gateroads in Chinese d mines .

Jan 1, 1997

By Takashi Sasaoka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 million tons of lignite annually from open-cut mining. The coal is used to generate 2,400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400? 500 m (1,312?1,640 ft) deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m (82 ft) thick with 20?25 m (66?82 ft) of interburden between them. Up to now, many mining systems for thick coal seams have been used and improved in the world. However, where the thickness of coal seams is beyond the limitation of the current mining technology and system, an applicable mining system has to be introduced, considering influencing factors such as caving and subsidence. In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early2009. This paper describes underground mining systems for thick coal seams and proposes an innovative underground mining system for thick coal seam, ?eco-friendly underground mining system?, considering geological, geotechnical, and environmental conditions in this mine. This paper discusses its applicability to this mine by means of numerical analysis from the geotechnical point of view.

Jan 1, 2011

By D. W. H. Su

A two-year study was conducted by CONSOL in a northern West Virginia coal mine to evaluate pillar design and support requirements to improve roof control in right-hand longwall headgates subject to high in situ horizontal stresses. Horizontal stress measurements conducted within undisturbed areas of the subject mine revealed a pre-existing regional horizontal stress field with a significant difference in magnitude between the east-west maximum and the north-south minimum stresses. Three¬dimensional stress cells installed to monitor horizontal stress concentration in the headgate roof during mining revealed that a narrow (60-foot center) headgate pillar reduces the east-west horizontal stress concentration in the roof ahead of the face such that the headgate is more stable and requires less support. This 60 foot x 140-foot pillar design, which has been employed in subsequent panels, still provides adequate stress attenuation to protect future tailgates under a maximum cover depth of 1000 feet. Roof geology derived from underground roof reconnaissance and underground bolt load and roof displacement measurements confirmed the effectiveness of 12-foot long cable bolts for controlling the headgate roof subject to high horizontal stresses. With the new headgate pillar design and the supplemental cable bolts, headgate roof conditions in the subsequent panels improved significantly, longwall production delay due to adverse headgate roof condition was totally eliminated, and record coal production was achieved by the subject mine in the subsequent years.

Jan 1, 2003

By Guy Reed, Russell Frith

"Current coal pillar design is the epitome of suspension design. A defined weight of potentially unstable overburden material is estimated, and the dimensions of the pillars left behind are based on holding up that material to a prescribed or user-defined Factor of Safety. In principle, this is seemingly no different to early roadway roof support design. However, for the most part, roadway roof stabilisation has progressed to reinforcement, whereby the roof strata is assisted in supporting itself. This is now the mainstay of efficient and effective underground coal production. Suspension and reinforcement are fundamentally different in their roadway roof stabilisation approach and, importantly, lead to substantially different requirements in terms of roof support hardware characteristics and their application. In suspension design, the primary focus is the total load-bearing capacity of the installed support to ensure that it is securely anchored outside of the potentially unstable roof mass. In contrast, reinforcement recognises that roof de-stabilisation is a gradational process with an ever-increasing roof displacement magnitude leading to ever-reducing stability. In a reinforcing situation, key roof support characteristics relate such design issues as system stiffness, the location and pattern of support elements within the roadway, and mobilising a defined thickness of the immediate roof to create (or build) some form of stabilising strata beam. The objective is to ensure that horizontal stress acts across the roof of the roadway and is maintained at a level that prevents mass roof collapse. This paper presents a prototype coal pillar and overburden system representation where reinforcement, rather than suspension, of the overburden is the stabilising mechanism via the action of in situ horizontal stresses within the overburden, the suspension problem potentially being an exception rather than the rule, as is also the case in roadway roof stability. Established principles relating to roadway roof reinforcement can potentially be applied to coal pillar design under this representation. The merit of this assertion is evaluated according to documented failed pillar cases in a range of mining applications and industries found in a series of published databases. Based on the various findings, a series of coal pillar system design considerations and suggestions for bord and pillar type mine workings are provided. This potentially allows a more flexible and informed approach to coal pillar sizing within workable mining layouts, as compared to common industry practices of a single design Factor of Safety (FoS) under defined overburden dead-loading to the exclusion of other potentially relevant overburden stabilising influences."

Jan 1, 2017

By Marcel0 Mondring

Transportation and the logistic requirements are set very high for the German coal mining industry. Short transportation resources, crowded quarters, and long transportation distances to destinations are some basic conditions that logistic employees of the mines have to deal with. Therefore, in the context of these processes, human effort and technology are faced with great challenges. There can be a total of 300 transport units, depending on the size of the mine. Every day, they are moved through a nearby 150-km-long transportation network of floor and monorail tracks. Of these transport units, 150 are new, and the other 150 units are split into cross traffic units that are moved only in the underground and return travel units. Beside track-bounded transports, all material transports take place in the shaft. As a result, many involuntary transports and changes in the means of transportation make the daily work more difficult. Typical transports in the shaft include the supply of new materials from above to below, as well as returnable goods from below to above. Cross traffics throughout several levels, which are rather rare, would have to be handled above the shaft. Due to limited shaft capacity, these cross traffics should be avoided when possible. Based on the gas resources in coalmine slopes, track-bounded transports using monorails (powered by diesel or rechargeable means) are preferred. This depends on the road degree, the depth, and track cross section of the shaft/slope. The variety of the material spectrum includes more than 100,000 different types of material.

Jan 1, 2014

By Thomas M. Baraak

This paper evaluates factors which influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: 1) longwall panel, 2) powered roof supports, and 3) gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from subsidence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data suggest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 1990

By Archie Richardson

Periodic weighting of longwall supports occurs during retreat ofthe face under certain geologic conditions. Strong stratain the immediate and main roof tend to cantilever over the gob, weighting the supports periodically. The distance between weighting peaks, as well as the intensity ofperiodic weighting, is determined by the suength and thickness of roof members, their location relative to the seam, the frequency of joinling, and characteristics of the gob. In this paper the effects of varying several of these variables ate investigated using block modeling. The models are calibrated against a published case history of periodic weighting in the Pittsburgh Seam. It is concluded that block modeling is a useful tool for correlating measured support pressure histories with expected modes of strata behavior in the roof, with potential for predicting shield behavior in new geologic enviromnents.

Jan 1, 1998

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By David Bigby

A remote reading dual height telltale system has been developed to provide mine management with early warning of impending roof failure. This system is a logical development from the visual dual height and triple height telltales which are increasingly being used worldwide for routine monitoring of mine roof. The paper describes the principles and history of telltales from their origins in France, their refinement and routine use in the UK and their subsequent spread around the world. They are now being used in various forms in USA, Canada, Germany, Spitzbergen (Norway), Poland, Ukraine, Russia, Australia, South Africa, Mexico, India, Egypt and China. The remote reading telltale system has coal mine intrinsic safety approval in Europe and the United States (MSHA) and the first commercial system was installed in a German colliery at the beginning of the year. Up to 100 dual height telltales can be connected, in a simple "daisy chain" configuration, to each of 4 underground interrogation units. These are connected through a twisted pair link to a surface computer which displays the readings, updates the database, generates warnings and provides the user interface. The paper describes the features and principles of operation of the system which differs considerably from conventional mine-wide monitoring systems. A European Community funded research programme is currently underway with the aim of developing improved alarm generating algorithms including evaluation of interfacing a neural network to the system. The paper concludes by exploring other potential applications of the system for ground control monitoring currently in development, including extensometry, stope closure monitoring and support load measurement.

Jan 1, 2001

By Gregory M. Molinda

The U.S. Bureau of Mines has developed a rock mass classification system for coal mine roof control. The Coal Mine Roof Rating System (CMRR) evaluates the structural competence of mine roof using simple field tests and observations obtained from underground exposures in roof falls or overcasts. The basis of the WRR is a weighing system which converts descriptive geologic roof rock data to a numerical value, facilitating its use in engineering design. A full suite of data collection and hand calculation sheets accompanies the CHRR A data base is currently being collected from all major coal basins in the United States to validate the CMW. To date, CHRR values are available from 96 roof exposures in 59 coal mines representing these basins. The system can be used to help solve many practical ground control problems, including longwall gate road design, roof support selection, and decisions regarding extended cut length.

Jan 1, 1993

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By Lisa Burke

In underground coal mines, concrete block stoppings are widely used to control mine ventilation. Although stoppings are not intended as roof support, they are subjected to roof to floor convergence, and may fail as a result of this loading. Premature failure of stoppings can significantly affect mine ventilation, limiting the amount of fresh air reaching the working faces and increasing the risk for methane explosions. Softening materials are often used in stoppings to reduce the damaging effects of roof to floor convergence. However, to date, research has not focused on the behavior of stopping construction materials subjected to roof or floor loading, leaving the design process to trial and error. A combination of numerical simulations and large scale physical tests were employed to develop a scientific understanding of stopping performance. The first series of physical models were constructed using standard CMU (concrete masonry unit) blocks and tested in a load frame. The behavior of these walls was simulated with a distinct element model. A key finding was that very small variations in block size and irregularities in block shape significantly affect wall performance. These variations, which are inherent to the type of blocks typically used underground, create stress concentrations that initiate the failure of stopping walls. A second series of models employed concrete stoppings that incorporated woos planks, a shredded wood material, and foam planks like those commonly used underground. Numerical models were again able to match the physical test data. Analysis of the softening layers used in stopping construction indicated that the strength and stiffness of the material relative to that of the wall is crucial in determining the amount of roof to floor convergence the wall can withstand prior to failure. The product of this study is a numerical model that can be used to evaluate the performance of stopping materials and different wall geometries in a controlled environment. Testing was done in a laboratory setting with walls constructed on flat, parallel surfaces and subjected to uniform loading at a constant rate. Parametric studies with the model indicate that in this ideal environment it is possible to control the amount of vertical displacement the stopping can withstand by adjusting the number of softening layers built into the wall and the thickness of the layers. Additionally, under these conditions, the position of softening layers within the wall appears to have little effect on the amount of displacement walls can withstand prior to failure.

Jan 1, 2004

By Brian G. D. Smart

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be represented.

Jan 1, 1992

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By Mingju Liu

In this research, we measured fractal characteristics of over ten typical outburst areas on different scales and related them to their outburst proneness, in attempts to provide new methods for outburst prediction. It was shown that both faults and folds follow the power law on coal basin scale, mine scale or mining district scale, whichever it is. Fractal dimensions are appropriate indices to describe geological structures quantitatively. Preliminary relationships have been established between outburst proneness and fractal dimension. Comparisons have been made among fractal characteristics and degrees of outburst proneness on all three scales. The results indicate that multi-scale assessment of outburst proneness can be made based on fractal measurements independently or supplemented by other assessment methods.

Jan 1, 2000

By Quanxi Wang

This paper presents a new stability mapping system which tightly integrates structural and geologic mapping with geo- mechanical stress analysis for use in support design and mine plan- ning. The structural and geologic input can include such local characteristics as: rock strength, layer thickness, faults, stream val- ley effects, etc. The geo-mechanical stress inputs can include overburden stress, multiple-seam stresses, abutment stresses, etc. The mapping system utilizes the popular AutoCAD/SurvCADD platform as a foundation for inputting the geologic characteristics, and then integrates the boundary-element program LaModel for determining the geo-mechanical stress influences. Additional func- tionality in the system allows the user to transform each individual geologic or stress factor into an individual rating and then the user can apply various weighting functions to the individual factors to generate an overall stability index map for the mine property. A sample case study is included in the paper to demonstrate the basic concepts, procedures and utility of the stability mapping system.

Jan 1, 2005

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004