Search Documents

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008