Search Documents

By C. W. Nelson, A. G. Moody

This paper describes the design, equipment selection and onshore fabrication of the largest facilities module ever installed in a single lift in the Gulf of Mexico. Measuring 35.5 x 70.1 x 21.3 m (110 x 230 x 70 ft), the three operating level structure houses Frasch process sulfur mining equipment and weighed nearly 49 million N (5500 tons) during lift. An operating weight of over 74 million N (8300 st) combines with bridge reactions acting on the in-place module and results in a total operating vertical load on the supporting platform deck of about 107 million N (12,000 tons). A Vierendeel truss structural system was selected for framing the module to allow maximum equipment access and routing flexibility for complex, insulated large diameter process piping. Research and finite element analysis of crimp plate siding behavior in shear was carried out during selection of siding type for the module. An interactive design sequence was carried out that incorporated in-place operational criteria, onshore fabrication considerations, complex process equipment requirements, plus load-out, ocean transport and offshore lift analyses. Project schedule dictated that design, procurement and fabrication be fast-tracked with parallel activities accelerated to the maximum extent possible. Design and construction of this largest and most complex module was done concurrently with 52 other components of the project including jackets, decks, process and living quarters modules as well as two 122 x 22 m (400 x 72 ft) sulfur tankers. Total tonnage of steel structures for the project exceeded 90.7 kt (100,000 st). The 5 kt (5500 st) mining module proved the viability and costeffectiveness of larger modules than commonly used in Gulf of Mexico waters. This technical advance can be matched with economic opportunity for other large-scale offshore installations.

Jan 1, 1994

By Jean-Pierre Nossereau, Allen J. Hulshizer

The main thrust of this paper covers the design, installation techniques and experience associated with the installation of eleven 1.5 m (4'-11") and three 2.87 m (9'-5") diameter shafts in 15 to 23 meters (50 to 75 ft) of water over 1.6 Km (a mile) out in the Atlantic Ocean. The approach implemented, permits the use of pre-fabricated shaft linings and incorporates a safe dry-tap method for connecting the offshore shafts to tunnels driven blind from deep land shafts over 4.8 Km (3 miles) away. This tunnel-shaft system is a unique venture employed at the Seabrook Nuclear Power Station to meet plant cooling water requirements.

Jan 1, 1981

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By Wendell H. Wiser

A comparison is presented of coal pyrolysis at temp¬eratures ranging from 4090 to 497°C and thermal dissolution of coal in tetralin at temperatures ranging from 350° to 450,°C, both utilizing a Utah high-volatile bituminous coal. The initial coal pyrolysis reactions are second order with an enthalpy of activation of 35.6 kcal per mole. The fraction of total product yield produced under second order conditions ranges from 67% at 409°C to 96% at 497°C. The process then gradually deteriorates to a first order reaction in the later stages with enthalpy of activation of 4.1 kcal, per mole. The initial reactions of solution of coal in tetralin are second order with an enthalpy of activation of 28.8 kcal per mole. The fraction of total product produced under second order conditions ranges from 63% at 350°C' to 94% at 450°C. The dissolution process then gradually changes to first order in the later stages with enthalpy of activation of 15.6 kcal per mole. A model is presented which relates the two processes and explains, the significance of the above similarities.

Jan 1, 1967

By Peter Johnson, David Barber, Lachlan Henderson

"Within underground portions of metro rail networks the traditional approach to a design fire has been to assume a worst credible railcar fire and develop ventilation and egress measures for life safety. This approach is being challenged as a rail network approach to design fires becomes a more practical and realistic approach. The network approach is based on utilizing an in-depth hazard analysis, to understand ignition and fire load sources in tunnels, above and below the floor of the railcar and within stations, and then utilizing a quantitative risk assessment to determine sets of fire scenarios. The process allows small, medium and large fires to be considered, with the consequences also being quantified. The selection of design fires has a significant influence on fire protection measures within a metro network and hence, is a major cost input. The rail network approach provides more robust decisions on fires, based on the hazards present. INTRODUCTION A fire within a rail car or one that occurs as part of a rail system can threaten the lives of users, maintenance staff and emergency services personnel. Fires in metro systems are rare events but can have severe consequences. As a result, any analysis of a potential fire must be thorough and rigorous and address not only regular accidents and small fires, but also very low probability, high consequence scenarios. The fire safety design process for a tunnel and station must start with the design engineers, contractor and operators making a number of key decisions related to fire protection measures, which may have significant cost considerations. One of the key aspects that influences the required fire protection is the design fire and the design fire scenarios, which is a key input for analysis. This paper provides an overview of the author’s experience in designing fire protection measures for rail networks in Europe, Australia and NZ, where a risk based framework is used to develop design fires and scenarios for the whole rail system – trains, stations and tunnels. This system wide approach is innovative, challenges the norms, but provides significantly more informed outcomes. The range of design fires will include small fires that may halt the network, larger fires for smoke hazard system design and significant post-flashover fires to assess the structural response."

Jan 1, 2016

By J.N. Kohmuench

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters, including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By John W. Antalovich

Normally I would like to begin a talk on photogrammetry by defining the word. However modern technology has changed the science so radically that it bears little resemblance to its original definition. Photogrammetry as defined is a science of taking accurate measurements from photography. Today's photogrammetrist, in addition to working with photography, finds himself working with magnetometers, infrared scanners, radiometers, holo¬graphy, lasers, side-looking radar, digital interfaces, computers and countless other modern space age concepts. The modern photogrammetrist is a pilot, photographer, lab technician, mathematician, geologist, programmer, engineer, physicist, and cartographer. His modern instrumentation and many spheres of activity all have a role in the environmental sciences. For example, the magne¬tometer which measures the earth's magnetic fields is used to locate the earth's ore deposits. The infrared scanner captures the heat emitted from the earth to detect ground waters and thermal pollutions. To elaborate on each of his many endeavors would take volumes rather than this short paper. I have elected therefore to discuss what I feel is his most important role in the environmental sciences - that of cartographer.

Jan 1, 1970

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By G. Vik, P. Chryssanthakis, S. C. Bandis, L. Haruik, N. Barton, M. Christianson, A. Makurat

The large jointed chalk reservoir situated at 3 km depth in the North sea's Ekofisk field is undergoing major compaction after nearly 15 year of oil and gas production. Approximately 150 km 3 of the overlying sediments, mostly shales, are involved in the subsidence. A maximum central subsidence of nearly 3 meters, and a maximum present rate of 45 cm per year has set in motion numerous studies of the phenomenon. Non-linear finite element (FEM) and non- linear distict element (DEM) analyses of the compaction and large scale subsidence were performed. Consistent differences between the continuum and discontinuum analyses were noted. In the latter, slip on hypothetical bedding planes and sub- vertical or vertical faults was allowed, which possibly gives a more realistic simulation of the real processes of subsidence in such a large body of rock. Laboratory studies of the reservoir joints included roughness measurement, JRC and JCS characterization, direct shear tests while saturated in heated Ekofisk oil, and coupled closure-shear-flow tests with heated oil followed by heated sea water. Discontinuum modelling using Cundall's UDEC was performed on representative jointed assemblies (two sets of steeply dipping conjugate joints) to investigate the effect of a major reduction of pore pressure within the deformable matrix and along each joint. It was found that the large shrinkage deformation of the matrix allowed joint shearing to occur despite the constraint of uniaxial strain. Relative mass bulking due to small but widely distributed joint shear possibly explains the observed maintenance of excellent productivity despite large vertical strains in the reservoir.

Jan 1, 1986

By D. E. Martin, K. J. Hamill, H. J. Miller

1. INTRODUCTION In April 1979, the U. S. Nuclear Regulatory Commission issued the Draft Generic Environmental Impact Statement (GEIS) on Uranium Milling (NUREG-0511) for public comment. While the GEIS is a broad environmental impact assessment of the U.S. uranium milling industry as a whole, its primary focus is on the issue of uranium mill tailings disposal and long term isolation. In August of 1979, proposed regulations (U.S. Federal Register Notice 44FR50012), incorporating both conclusions of the GEIS and provisions of recent U.S. legislation on uranium mill tailings (Uranium Mill Tailings Radiation Control Act of 1978--UMTRCA), were also issued for public comment. This paper (1) briefly reviews the major conclusions of the draft GEIS, (2) summarizes the major elements and rationale of the associated, proposed regulations, and (3) reviews some of the major issues raised during the public comment period and changes which the NRC staff expects will be made in finalizing the GEIS and regulations. The risk in summarizing a document of such broad scope and complexity as the GEIS is that the depth of evaluation and the full technical bases for conclusions reached may not be adequately conveyed. Recognizing this, those Sections of the draft GEIS where a more complete discussion of the issues is presented are parenthetically noted in this paper in order to facilitate location of additional background and supporting material. 2. GENERAL CONCLUSIONS In the GEIS, a full range of tailings disposal alternatives was considered. These alternatives ranged from the past practice of doing little or nothing to control tailings, to advanced treatment alternatives such as nitric acid leaching to increase removal of radioactive elements and fixation of tailings in cement or asphalt. Our broad conclusions were: -Any alternative which results in the need for ongoing, active maintenance to assure long term containment, is unacceptable. (12.3.2.1) -Advanced treatment alternatives are unwarranted since they offer uncertain incremental benefits yet involve costs which may be as much as an order of magnitude greater than costs associated with acceptable alternatives. In addition, the advanced treatment

Jan 1, 1980

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968