Search Documents

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

The need for geological control in orebody estimation and modelling is self- evident to geologists and mining engineers engaged in practical day-to-day estimation. It is only fairly recently, however, that attempts have been made to incorporate explicitly such requirements into published accounts of geostatistical estimation; see, for example, Dowd and Scott (1982, 19841, Rendu and Readdy (1982), Dagbert et al. (1984), Dowd (1984), Benest and Winter (1984). In practice, many geological controls in automatic or semi-automatic estimation and modelling are essentially geometrical controls. The aim of this paper is to present two techniques for geological/geometrical control. Whilst the applications are new, neither technique is entirely original and both have been adapted from other fields and sources. Both techniques are, in some sense, types of estimators and/or interpolators of shapes. The first is a method for fitting spline surfaces to control orebody boundary estimation and to unroll orebodies. The second is an application of Minkowski addition to interpolate shapes such as orebody outlines or stope boundaries and to control estimations.

Jan 1, 1986

By T. Tomioka

1. An Overall View of the Japanese Ferroalloys Industry 1) Depressed Demand for Ferroalloys: In Japan consumption of ferroalloys in the last ten years has decreased, although there has been some fluctuation from year to year. During this term production figures of the steel industry, which are closely related to consumption of ferroalloys, are as follows: Shipment of steel products for the domestic market has declined gradually from 69 million tons in 1979, which was the peak year for steel production, to 60.3 million tons in 1982 and 60.4 million tons in 1983, the level of 1978. In addition, exports also have been a downward trend since 1976, which was the peak year with tonnage of 34 million tons, to 28 million tons in 1982 and 31 million tons in 1983.

Jan 1, 1984

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By J. J. Whittaker

Zaldivar is an open pit copper mine operation located in the Atacama Desert, in northern Chile. The plant produces Cu cathodes using 4 solvent extraction trains. The plant was started up May 1995. Since 1996 the plant has been using on-stream analyzers based on X-ray fluorescence and titration for process monitoring and control. Elemental analyzer alone is not able to provide the critical information for plant operation, it has to be complemented by on-stream titrators integrated to one sampling system. The analyzers are located in a prefabricated shelter. The analyzer system project, operation and performance issues are the main topic of this paper.

Jan 1, 1999

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

By M. D. Chatham

Revolutionary electronic monitoring and control systems provide a gold mine of diagnostic and prognostic information. Lower cost per ton results from timely operator action, increased visibility of information to production and maintenance personnel, and better fleet management. When information is effectively integrated into fleet management systems lower costs result from higher availability, longer component life and reduced repair cost. This paper will present the objectives of the Caterpillar Vital Information Management System (VIMS) and provide actual examples of successful use.

Jan 1, 1995

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993

By Dale K. Fields

With today's technological advances in mineral processing equipment, there is an increasing demand for accurate system control. This can only come about through representative sampling. The purpose of this paper is to guide you in the selection of sampling equipment and outline design parameters for the cutters used in dry and wet sampling without adding redundant mathematical probability formulas to your files. Special attention will also be given to the equipment used in conjunction with samplers and sampling systems, such as feeders, crushers, chutes, launders, and controls.

Jan 1, 1979

By Robert M. Cox

A thorough geological engineering investigation is required before surface lands overlying abandoned underground mines can be safely recommended as building sites. The major problems confronting the geological engineer are assembling accurate geologic and mining information and developing an accurate rock mechanics model of the situation. A successful investigation requires a combination of technical expertise in rock mechanics and engineering geology tempered with practical engineering judgment. The results of a good study are not always favorable to the prospective builder.

Jan 1, 1975

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By Alain A. Sonntag

This paper presents the most recent developments in KREBS technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1989

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980