Search Documents

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By Heinz Distelmeier

Short Historical Review Tunnelling in Germany is as old as it is in other industrial countries. Until the middle of this century German contractors had no chance to work continuously in this business except if they were operating internationally. Since 1960, however, tunnelling has been a growing market domestically. The reasons for this growth have been both in the growing demand of traffic routes and also in an increasing environmental consciousness, which tries to transfer any cause of disturbance underground. Tunnelling engineers of course don't complain about this trend. As almost every German city is built upon water-bearing soft ground, shields have been used soon after they were first successfully utilized in Great Britain and the United States. Until the seventies lining systems for shield tunnels were predominantly either cast iron segments or concrete segments for primary support combined with different sealing systems and a secondary concrete lining cast-in-place. Steel ribs and timber lagging for primary support has not been utilized in Germany, since the owners don't accept timber to be left in the ground. In 1973, for the first time, permanent linings were constructed with watertight segment rings of precast concrete (Fig. 1). This lining was developed as an economical solution for use with slurry shields in noncohesive, water-bearing soils that required an immediately watertight lining. Extruded linings have a similar effect, although these still need a secondary lining

Jan 1, 1987

By Ing. Ludwig Schlebusch

The significant growth of the world population and its demand for an increasing standard of living leaves no other choice than continuously augmenting industrial production and making available steadily greater quantities of raw materials at still better qualities. Therefore, any raw material has to be utilized to the greatest possible extent and processed at optimum economy on large mechanical equipment. The layout of processing facilities of large throughput rates can be based on multiple or single lines. The latter enables the application of large machines of optimum size. Proven equipment for homogenizing, classifying, separating superfine material, sorting and dewatering are-now available in optimum sizes. By the use of these large machines operating cost of pit coal preparation plant can be significantly lowered by reducing the specific requirements regarding space, capital investment, energy, operation and maintenance.

Jan 1, 1980

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By Jr. McCulloch

Mining operations of Freeport Indonesia (FI) are located approximately 4 degrees -6' south latitude, 137 -7' east longitude in Irian Jaya the eastern most state of Indonesia (Figure I). The mines are located approximately 96 km (60 miles) from coast in the Carstenz Mountain range. The ore bodies are between 2900 and 4000 meters (9500 and 13 000 ft) elevation.

Jan 1, 1989

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

By Dwight K. Smith

Fly ash as an additive for oil well cement was introduced to the oil industry by the Halliburton Company in 1949. Since its early usage in the Illinois area of the U. S., the total amount of fly ash pumped into wells has exceeded 30 million sacks, The advantages of using fly ash-portland cement mixtures in wells are fundamentally the same as for concrete except the conditions of placement and curing are variable and the nomenclature of properties are expressed somewhat differently. In some instances deep wells have been cemented with mixtures of fly ash and hydrated lime together with an activator which functions as a catalyst for setting. This fly ash-lime formula has many advantages for high temperature-pressure conditions found in wells.

Jan 1, 1968

By F. Kitzinger

The possibility of increasing the efficiency of mineral processing plants by means of computer control has prompted metallurgists to examine their flowsheets more critically in order to develop practical control strategies. Control schemes in use to date generally rely on the automation of traditional and previously manually regulated control loops, for instance the addition of reagents to maintain a constant assay or a constant pH. This approach is predicated on the availability of well-established primary sensors such as pH electrodes or on-stream analyzers. Noranda Research Centre, in cooperation with Noranda Group concentrators, has developed a froth level monitor and a pulp density meter susceptible of application in this type of control. Although some of the basic principles on which they are based have been known for some time, their incorporation into the design of reliable, direct-reading instruments which can be interfaced with a computer, is be-lieved to be novel*.

Jan 1, 1977

By Vinton A. Garbesi

INTRODUCTION The placing of the monolithic concrete lining of the Bi-County water tunnel illustrates the state of the art in the materials, equipment, methods and productivity available to the industry for this type of construction. This paper describes the management and engineering rationale used by Clevecon, Inc., a subsidiary of S & M Constructors, Inc., Solon, Ohio, in developing the concrete mix designs, the design of the specialized equipment, and the methods used in the manufacture, transport, and placing of the lining. Also discussed are the changes to the reinforcing steel design instigated to facilitate its handling and placing, as well as to enhance the quality of the lining. The intent is to bring to the attention of designers the effects certain design aspects have on the construction of reinforced concrete tunnel linings, as well as indicate the areas where research and development effort should be expended to further reduce costs for this type of construction. GENERAL DESCRIPTION The Bi-County Water Tunnel West is a water transmission main owned by the Washington Suburban Sanitary Commission of Hyattsville, Maryland. The facility was designed by A. A. Mathews Division (formerly STRAAM Engineers, Inc.) CRS Group Engineers Inc., Rockville, Maryland. It is to be utilized as the central feeder of potable water for the northern suburbs of Washington, DC, extending some 4,597 meters from a riser shaft at its western terminus to the eastern interface, with a similar tunnel which extends eastward about 5,180 meters; the majority of its length being under Interstate Highway 1-495. The excavated and finished diameters are 3.8 and 3.05 meters respectively. The reinforced concrete

Jan 1, 1981

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By Jerry L. Hodgson

This paper presents an application case history of the planning methods used for developing, costing and scheduling an underground hydro- electric pumped storage facility in weak rock. This method covers the system configuration, excavation methods and costs, initial support systems and final lining systems. This study was performed by the Omaha District, Corps of Engineers for the proposed Gregory County Hydro- electric Pumped Storage Project, and presents a synopsis and the results of the studies performed.

Jan 1, 1986

By V. Badaker, R. J. Sweigard, C. D. Barton, J. W. Stringer, J. M. Ringe, A. D. True, D. H. Graves

Field studies have demonstrated the relationship between the growth of high-value trees on surface mined land and the physical conditions of the root growth medium. Specifically, the survival and height of hardwoods grown on less compacted material are far superior to those grown on compacted material. Furthermore, studies have demonstrated that the physical condition of the root growth medium can be characterized by dry bulk density and penetrometer resistance and that these parameters are also related to tree growth measurements. Site indices are useful for evaluating and predicting the productivity and timber yield for a specific location. A method has been proposed to estimate the site indices for various tree species on reclaimed surface mined land as a function of the physical properties of the root growth medium.

Jan 1, 2005

By H. Singh

Principal source of rhenium is molybdenite. Depending on the mineral processing route, rhenium can be recovered by one of the several alternative solvent extraction processes. Extensive experimental work has been carried out on the development of tertiary amine extraction process for treating very dilute highly impure scrub solutions obtained during scrubbing flue-gases of molybdenite oxidative roasting. Equilibrium data has been obtained under various process conditions by tracer analysis using radioactive Re-186. Extraction with 1% solution of a high molecular weight tertiary amine in kerosene, followed by scrubbing of organic extract with a solution of sulphuric acid and stripping with ammoniacal ammonium sulphate yields high recovery, concentration, and purification.

Jan 1, 1982

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By J. C. Willett, J. R. Sanfilipo, S. M. Podwysocki, P. D. Warwick

The U.S. Geological Survey is concluding an assessment of the major coal regions of the country. In this program, the quantity and quality of coals that are expected to be mined during the next 30 years are characterized. For the Gulf Coast region, the evaluation includes reviews of the stratigraphic setting, coal resources, and the quality of the Cretaceous to Eocene coals in four coal-producing areas. The coal-bed methane potential for these areas will also be evaluated. The results of these efforts will be a series of digital maps, text, and tables that will be published in a CD-ROM format.

Jan 1, 2000

By Wojciech Klecan, John H. Raymer

Baseline quantities of difficult ground and support types were estimated for the Chattahoochee Tunnel using the Rock Mass Rating system. RMR classifies the ground into five categories, ranging from “very good” to “very poor,” based on five main parameters: intact rock strength, RQD, joint spacing, joint condition, and groundwater inflow. For the Chattahoochee Tunnel, these parameters were independently measured in the cores and shown graphically on the boring logs. A 55 matrix was calculated to obtain the statistical distribution of RMR for the project. Three baseline ground types were defined based on the RMR. Geologic mapping inside the tunnel during construction has verified the accuracy of this method.

Jan 1, 2003

By Rick Sarkisian, Albert D. Bonneau, David Keech

The Drummond Co. Inc.'s Shoal Creek Coal Mine Slope Belt Conveyor transports 5000 mtph (5500 tph) of material over a length of 1400 m (4600 ft.) and a lift of 3609 m (1180 ft.). Four 1500 kW (2000 hp) motors power the 1830 mm (72 in.) Goodyear Flexsteel 5800 steel cable belt. In May 1993, Dodge Manufacturing was selected to design and build the conveyor pulley assemblies for this conveyor. The conveyor includes five pulley assemblies. The 2135 mm (84 in.) diameter by 2135 mm (84 in.) face primary and secondary drive pulleys were designed for a resultant belt load of 3060 kN (688,000 Ib.) This paper describes the design and manufacture of the two drive pulley assemblies. Design details included are component evaluation, material selection, locking assembly selection, bearing selection and lagging selection. Manufacturing details include material procurement, welding process, lagging installation and component assembly. Quality control procedures are also discussed.

Jan 1, 1996