Search Documents

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By Robert L. Wade

The two primary goals in underground coal mining are to improve safety and to lower mining costs per ton through increased productivity. However, as evidenced by the drastic decrease in. productivity since the enactment of the 1969 Coal Mine Health and Safety Act, (the Safety Act), these goals appear to be mutually exclusive. Millions of dollars have been spent in the res, arch and development of systems to solve this problem. Before the Safety Act, "productivity had experienced a 25-year history of continued increases ...? (Douglas, 1980). But since its enactment there have been dramatic decreases in productivity accompanied by phenomenal increases in mine costs. Labor trends, depletion of the more readily minable underground coal reserves and other factors have contributed to this situation, but the dominant factor is undoubtedly the Safety Act itself. To illustrate, prior to 1969 underground coal mine production was much greater than surface mine production but since then underground mine production has been declining at a rate greater than the overall growth rate of total coal production.

Jan 1, 1985

Selective Flocculation process development generally involves single mineral flocculation tests to identify the appropriate polymer and experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculent. Simultaneously, a mathematical model was developed to predict the overall process efficiency with a given polymer. In this paper, results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1991

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering. There exist no standardized methodologies for their computer implementation. In meeting this need, this paper introduces the concept of a process software model, or simply a software model and presents a two-step methodology for its development involving software model specification and development. The software model specification is to be performed after extensive discussions with the ultimate users of process software based on which the software model is developed. These software models provide a formal basis for the design and construction of software objects corresponding to the real world process objects.

Jan 1, 1994

By P. F. Mataich

When the subject of plant computers is brought up most people visualize the computer's controlling the entire plant with very little operator intervention. Actually, this picture is true today in only a limited number of cases and will certainly not be true in the minerals industries for many years to come. There are several ways in which a plant computer can significantly contribute to improving plant operation and closed loop control is only one of these. First of all, what are the basic ingredients for good plant control? For good plant control, two requirements must be met. First, the operator must get good information feedback from the process and then he must know what action to take in response to this information. Control information can be obtained through instruments, laboratory analyses, or through simple visual observation. If it is timely and accurate and the operator knows how to use it, then we have the makings of a good plant control system. The computer can be of help in both these areas by getting good data back to the operator and in helping to develop a good control scheme for the plant.

Jan 1, 1966

By C. J. Bise

Virtual Reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced fonn of computer graphics where the images are generated based upon where the user looks and how the user moves. As personal-computer-based (PC-based) instruction gains acceptance as an innovative approach to providing safety training, VR offers the capability of providing a multisensory, rather than merely a multimedia, mode of presentation. VR has been effectively used by the military for training tank commanders and by hospitals for training surgeons. However, these applications have been limited to small numbers of highly skilled participants. The purpose of this paper is to examine VR's potential for enhancing the hazard awareness of larger numbers of individuals in a broad-based approach to mine safety training, such as new-miner, annual-refresher, and independent-contractor training.

Jan 1, 1996

By Adolph V. Mitterer

International Minerals and Chemical Corporation operates one of six potash mines in the Carlsbad potash basin. More than 90 percent of America's potash is produced at Carlsbad and IMC accounts for about one-fifth of that amount, Since the Company began operations in 1941 it has mined nearly 50 million tons of ore. Of the two types of ore mined at Carlsbad the principal tonnage is sylvinite in which sylvite-potassium chloride-is the ore mineral. It is produced by IMC as well as by all other mines in the area, In addition to sylvinite IMC is the exclusive producer of langbeinite ore--potassium-magnesium sulfate. From its two ores, International produces a spectrum of 8 high-quality agricultural and industrial chemical products.

Jan 1, 1959

By George I. Staber

As stated by the Congress in the preamble of the act establishing the Office of Coal Research, its purpose is, "To encourage and stimulate the production and conservation of coal in the United States through research and development by authorizing the Secretary of the Interior to contract for coal research, and for other: purposes." Thus, while the overall responsibility for air pollution control from all sources rests primarily with the Department of Health, Education and Welfare, it is obvious that OCR could not perform its mandate of, increasing the utilization of our Nation's greatest energy resource if it ignored one of the greatest practical obstacles to achieving that objective. Therefore, air pollution abatement and prevention is one of the practical considerations taken into account in the selection of the OCR program. And as the severity of the air pollution problem imposes new restrictions on the use of coal, the importance of this criteria in the selection of OCR projects increases. The work done by OCR in air pollution abatement does not conflict with nor does it duplicate the program developed by HEW's National Center for Air Pollution Control. Technical members of the OCR staff maintain close formal and informal liaison with their counterparts in NCAPC. One formal agreement has been executed whereby the HEW agency has transferred funds to OCR for a practical study of the potential effectiveness of air pollution control when coal is burned in a fluidized bed comprised of inert alkaline earth material. It is hoped that this initial cooperative effort will be

Jan 1, 1968

By Richard Jr. Ray, David Johnston, Phil Blankenship

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1989

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By A. B. Fly

This paper presents the equipment and techniques developed to mine subsurface mineral deposits through 16 inch bore holes entirely by hydraulic methods. Use of this equipment for excavating large cavities in oil and water well producing zones is discussed. Results of surface experiments using high pressure jet streams of water to determine the cutting rates of materials are outlined. Various basic shapes of subsurface excavations that can be mined with the equipment are illustrated and discussed. An example of the cost of mining by this method is presented. Problems encountered in the field operations led to the development of a new explosion type slurry pumping system and related slurry handling equipment.

Jan 1, 1969

By John J. McCrone

In the Mining Industry, the means of handling and transferring lubricants has been given little attention over the years. An analysis of this process indicates that this neglect has often exacted a very high price. As the costs associated with labor, equipment utilization and waste disposal soar, the need for an efficient system takes on an increasing significance. Often the focus of bulk systems has been placed on the master container itself. Certainly, there is nothing new about a large lubricant container; they have been available over a period of years, known under a variety of names, "mini tank", "super drum", ?flo-bin" and "tote bin", to name but a few.

Jan 1, 1982

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By John D. Kalasky

Ventilation is necessary in coal mines to supply fresh air to the working faces for the health, safety, and comfort of the miners, and for the circulation of air to the extent that it will dilute, carry off, and render harmless the noxious or dangerous gases generated. Adequate ventilation depends upon good face control, as well as upon a well designed and properly controlled overall ventilation system. Generally, this includes fans, airways, overcasts, air locks, regulators, checks, and canvas or plastic stoppings near the working places to prevent short circuiting of air, and effective bleeders to maintain a continuous flow away from the working places along the pillar lines at all times and to prevent diffusion of methane back to the pillar line in case of temporary interruptions in ventilation. In the development of a new mine, or the virgin area of an old mine, the main headings should properly be considered a construction project, designed with, only the number of permanently supported (roof) headings required to conduct the necessary air volume to and from the major panels in which mining is conducted by room and pillar or longwall methods. Although subject to hazards from methane quite frequently and requiring constant and careful attention at all times, development of headings has some built in safeguards which make it a less difficult problem in control of methane than exists in pillaring.

Jan 1, 1973

By K. J. Henderson

INTRODUCTION Shrinkage mining at Inco Ltd.'s Crean Hill mine can best be defined as a horizontal breasting method utilizing the broken ore for the mining floor and to provide wall support, with draw from a series of boxholes or draw¬points at the base of the stoping block. In choosing to shrink a given block of ore, the initial investigation centers on the ore configuration and grade, the expected ground conditions in the stoping area, the expected profit compared to alternative mining methods, the future production requirements, development lead time, the availability and type of equipment in the area, and the availability of experienced miners. These factors are weighed against other mining methods and shrinkage mining is chosen when the advantages outweigh the dis¬advantages. These will be discussed in more detail later. At Inco Ltd.'s Crean Hill mine, shrinkage mining makes up 17% of total mine production and is decreasing due to the advent of advanced blasthole techniques, notably in-the-hole drilling. Shrinkage is an adaptable mining method that is currently employed in narrow irregular ore zones, as undercuts for in-the-hole blast¬hole stopes, in ore bodies that do not extend from level to level, and in areas where quick production is required with a minimum of capital outlay or minimum develop¬ment. Two major types are currently in use which are classified on the basis of type of draw system employed. These are the utilization of load-haul-dump (LHD) equipment drawing from drawpoints, and the slusher and train method drawing from boxholes into a slusher trench and loading into a train. A third method being phased out is drawing from chutes directly into a train. In all three methods the actual stoping operation remains the same. In the initial planning of a mining block, the ore body is first located using an exploration diamond drill¬ing program. This is essentially done at a 130-m (400¬ft) spacing and it gives an indication of the amount of ore, grade of ore, the configuration of the ore body, as well as other geological features such as ground condi¬tions which will affect future mining. This drilling is done from an exploration drift 165 m (500 ft) long in the hanging wall and covers a vertical extent of 330 to 670 m (1000 to 2000 ft). However, these data are not accurate enough for detailed planning. When the de¬cision has been made to mine, a preliminary develop¬ment drill drift is driven in such a position that it can serve the dual purposes of allowing the ore body to be drilled off in detail, or of later serving as a haulage or access drift. Diamond drilling from this drift is usually on a 15-m (50-ft) grid spacing and gives adequate information for detailed planning. Utilizing the drill data, a decision is made on the mining type. For a shrinkage operation, the stoping block is ideally 49 m (150 ft) in length and a maximum of 13 m (40 ft) in width. Lengths of 65 m (200 ft) are considered a practical maximum because of the length of time the back of the stope remains open during the min¬ing of a cut. A minimum length of 13 m (40 ft) is used because the amount of time spent in opening a new cut increases in comparison with the total stoping time. The maximum width of 13 m (40 ft) is used because ex¬perience with the ground indicates that generally stope backs tend to be unstable over greater widths. However, widths of 33 m (100 ft) have been mined. A minimum width of 5 m (15 ft) is used to allow an effective draw, but in unusual cases, a width of 3 m (10 ft) has been mined successfully. The dip of the ore should not be less than 1.04 rad (60°). Angles flatter than this will not pull properly resulting in inefficient mining because of ore hang-ups on the footwall side of the stope and the need for large stagings on the hanging wall. In considering shrinkage, mining ground conditions play an important role. Strong shearing, cross faulting, or dikes are avoided. These usually cause dangerous mining conditions and an alternative safer mining method which will give adequate support to these adverse ground conditions is employed. Production requirements are taken into considera¬tion when planning a shrinkage mining program. In it¬self, shrinkage mining is capable of producing ore in a relatively short time with little capital development. If quick production is required, this method can produce ore rapidly as all that is required is that the draw system be completed and the miners with jacklegs and stopers produce a limited amount of ore. The obvious disadvan¬tage is that not all the ore broken can be pulled from the stope immediately. However, a mining horizon with sev¬eral shrinkage stopes in different stages of production can adequately maintain scheduled tonnage require¬ments, the cycle being stopes under development, stopes actively mining, and stopes completed and pulling. When the decision has been made to use shrinkage mining in a given block, the haulage and draw system is driven. The proximity of the orepass system dictates whether the system is to be a LHD operation or a slusher trench operation. If the orepass system is in close prox¬imity to the stoping block, LHD equipment is employed because of its ability to operate efficiently over short haulage distances. A long tram to the orepass usually dictates a slusher trench operation with haulage by train. Internal orepass systems are used effectively with LHD equipment with a load-out and retramming taking place on a lower horizon. In addition, stoping blocks in older areas of the mine are developed track because of the capital cost involved in converting an existing level to trackless mining. DRIFT DEVELOPMENT USING LHD EQUIPMENT The haulage drift for a draw system using LHD equipment is driven parallel to the ore body in the foot¬wall at a sufficient distance to allow an 11.5-m (35-ft) drawpoint to be driven into the ore (Fig. 1). The actual position of the drift depends entirely upon the ore con¬figuration and the drift size depends on the equipment to be used. Drift sizes of 4.6 x 4.1 m (14 x 121/2 ft) for an St-4 and 3.8 x 3.6 m (111/2 x 11 ft) for an St-2 meet company and government clearance standards and allow sufficient space to accommodate a ventilation pipe. The

Jan 1, 1982

By A. J. Erickson

In mid 1970, Park City Ventures, a Utah partnership of ASARCO and TAC, initiated a six phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration tar¬gets in several areas of the district. Discovery of ore in any of the target areas and continued favorable down dip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: Mississippian Humbug Formation replacement mineralization below productive ore bodies on the east flank of the Park City Anticline; Humbug replacement mineralization in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade Humbug replacement mineralization in a theorized structural block on the west flank of the anticline beneath the Ontario Vein; Permian Park City Formation replacement mineralization in the West End Shaft Area of the Silver King mine; vein mineralization along the Back Vein in the Judge Mine. Chilean Nationalization in 1971 resulted in a 30% budget cutback. The Judge and Silver King Projects were suspended. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure; five new ore bodies were found in the Humbug, and Doughnut Formations on the west flank of the anticline beneath the Ontario Vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1976