Search Documents

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By Edward M. Belsky

Increasingly stringent government environmental regulations will affect the availability and costs of bonding and insurance products for the mining community. New regulations requiring Environmental Impairment Insurance, Reclamation Bonds, and Cyanide Use Bonds will result in both an increase in cost and a decrease in availability of affordable insurance and bonding pro- ducts. Professional Liability Insurance for engineers that covers pollution exposures will be a must for all professional engineers working in the mining community. By understanding the problem, solutions can be structured to allow your company to obtain the mandated insurance at the most favorable cost and conditions!

Jan 1, 1991

By F. Grandjacques

INTRODUCTION Selective Reduction of Nickel in Oxidized Ores Oxidized nickel ores, either garnieritic or lateritic, contain much more iron than nickel. The regular carbon reduction in an electric furnace is operated in such a manner that the greater part of iron oxides is reduced simultaneously with nickel oxide, resulting in a low nickel content ferronickel. In order that the nickel content of residual slag may be suitably low, -excess carbon must be fed so that the carbon content of the ferronickel thus obtained is that of casting iron. The metal also contains other impurities such as silicon, chrome, etc. In order to convert the casting iron into slightly carburized ferronickel with high nickel content, the greater part of the carbon and more than half the iron contained therein must be oxidized by means of oxygen. Energy is thus consumed as carbon, and power to reduce iron oxides, and more energy is consumed as oxygen to re-oxidize the iron contained. This method can be economically adopted for nickel ores with grades ranging around 2. 5 to 370, but it gets excessively costly when nickel grade falls below these values. This is why, for nickel ores with low nickel grades and high iron content, studies were conducted to develop a selective reduction process which, while reducing only a small part of the iron oxide, would provide efficient reduction of nickel oxide. Rich ferronickel is thereby obtained, with nickel content ranging around 30 to 50%. Due to the presence of slag with a high iron oxide content, the metal thus

Jan 1, 1979

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov

As a result of thermodynamic analysis of a mineral-sodium, oleate-water system, flotation and adsorption tests at various pH values, and sodium oleate concentrations, it has been established that due to regularities of phosphate-containing minerals (fluorapatite, hydroxyapatite, carbonatapatite) flotation cannot be explained by the formation of alkali-earth metal oleates on their surface. This paper presents a novel theory that connects optimal conditions for mineral flotation with zero charge of its surface, which can explain the regularity of minerals flotation observed. The quantitative physicochemical flotation models developed based on the theory are suitable for improving industrial processes, conditioning of recycling waters, and application in automatic control systems at the plants. Key words: apatite, oleate, flotation, modeling, control, and regulation.

Jan 1, 1999

By Richard M. Michaels

In considering the use of underground space for civil works functions, there are several criteria that must be met if transfer of any of them is to occur. It is important to recognize that these criteria involve social and political as well as conventional engineering and economic considerations. It is the purpose of this report to identify certain of these criteria and develop a set of measures that will permit the evaluation of the potential benefit of transferring civil works functions underground. The work reported here was completed for the ASCE and is contained in the report, Undergound Space, 1973. If one examines the total direct and indirect economic return from the location of civil works in subsurface rather than surface space, sizeable benefits accrue. This occurs largely because design, construction, operating and maintenance costs of these systems are highly dependent upon the forces exerted on these systems by the surface enviroment itself. Transferring of these facilities to underground space would eliminate a large segment of those costs. It is equally true that civil works functions compete with other uses for surface space and generate significant conflicts with these competing uses. Highway construction takes land from other productive uses. Electrical transmission lines conflict in terms of safety and aesthetics with adjacent social activities. Assuming that construction costs can be made equivalent, the analyses in the previous report indicate that the locating of all civil works functions underground would yield an annual net savings to the society of the order of 60 billion dollars. It may be added that the benefits in terms of improved social perfromance would also be substantial. However, it is clear that the benefits from utilization of subsurface

Jan 1, 1974

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016

By Gábor Antal, József Bõhm, Barnabás Csõke

From the waste material of the production of aluminium foil aluminium pigment is produced for the paint industry by grinding it in white spirit. During grinding 1-2 % iron impurity gets into the product, weakening its quality, from the wear of the mill armour and the grinding bodies and from the contamination of the raw material. For deironing the product, a stage-operated electrically induced magnetic filter separator was developed and put into operation. The separator was sited in an explosive environment and therefore required a special design and safety system. The paper describes the results of the development work. the device that was developed, the safety system as well as the results of and experiences with the operation of the separator.

Jan 1, 1995

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By K. N. (Mani) Subramanian

A 2.5 meter diameter column has been successfully used in a 100 tph flotation plant at the Harbour Lights Mine in Leonora, Western Australia, to produce a final gold bearing sulfide concentrate from the ore in a single stage. This pioneering application of column flotation cells to rougher stage was pilot tested using a 11 cm column, which demonstrated column's capability in rougher, scavenger and cleaner flotation stages. A hybrid circuit involving columns and mechanically agitated flotation cell s was adopted for the commercial installation. This paper describes pilot plant results, design of the plant flotation circuit, and early results of commercial operation.

Jan 1, 1988

By B. K. Mishra, R. K. Rajamani, R. Venugopal, P. Songfack

Millsoft is a computer-simulation software that predicts the performance of large industrial grinding mills. This software surpasses all other tumbling-mill analysis techniques available today because it is based on fundamental laws of physics instead of empirical correlations. Graphical user interface (GUI) forms simplify the specification of the following design and operating parameters: mill diameter, length, speed, charge density and size distribution, lifter material and geometry. All of these parameters are taken into account in the discrete element numerical technique that constitutes the essence of the simulation software. In turn, the software produces a visual animation of grinding-charge motion, predicts mill power and gives the distribution of impact energy. In this paper, a case study of an 8.5-m-(28 ft-) diam SAG mill is used to illustrate the application of Millsoft for mill design and trouble shooting.

Jan 1, 2000

By P. K. Davis, B. Gharib

The results of a previous basic study of the flow and design characteristics of hydrocyclones demonstrated that a recovery as high as 99% with a product rating* of 0.95 can be achieved on a batch+ basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-¬cyclone system was sponsored by the US Department of Energy, which also sponsored the initial study. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1990

Floc properties such as density, size, size distribution, porosity and shear strength govern the effectiveness of flocculation as a process for solid-liquid separation. Floc characteristics desired for removal of suspended solids by sedimentation or filtration, for example, are known to be different. In this study, an attempt has been made to evaluate floc density using a simplified procedure and determine the effects of various physical and chemical factors on the density of floes obtained. A brief discussion of techniques employed to measure the shear strength of flocs and the effect of various parameters on the floc strength is also presented.

Jan 1, 1988

By E. S. Smith, Sunirmal Banerjee

INTRODUCTION Social awareness of the detrimental impact of man-made wastes on our environment has grown considerably during the last two decades. Increased public and institutional concerns have resulted in the implementation of a wide variety of regulatory controls of disposal of wastes. These regulations have often reflected significant conservatism in expecting guaranteed elimination of pollution risks. This sort of expectation assumed a state of knowledge which was not readily available to the major producers of wastes. The mining industry, in particular, has been affected by such regulations in terms of excessive costs and loss of benefit. As a result, investigations are in progress (1) to generate newer methods for satisfactory stabilization of mine and mill wastes and (2) to apply the available technology to achieve the standards set by the regulatory agencies at reasonable costs. This paper presents a conceptual scheme for stabilization of mill wastes by suitable management of operations and accelerated consolidation of tailings slurries. The main discussion in this paper is aimed at the ability of the proposed scheme to address the major considerations in effective disposal. Comparison in both cost and effectiveness are also made between the proposed scheme and various other currently used disposal concepts. MAJOR CONSIDERATIONS IN EFFECTIVE DISPOSAL The primary objective of an effective tailings disposal scheme is to provide containment of the contaminants in such a manner that the undesirable impact of the wastes on the three basic elements of our environment--land, air, and water-would be minimal. Bearing the above objective in mind, one may justifiably list the major considerations in the choice of the disposal scheme in terms of its effects on land, air, and water (Bromwell, 1976) as follows: Effects on Land (1) whether the scheme makes optimal use of land.

Jan 1, 1980

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By D. R. Zeni

Today's mine development requires the safe, expedient and economical construction of vertical shafts for both ventilation and access. This construction must be accomplished within diverse ground conditions. Advancements in large-diameter shaft drilling have led to many exceptional mechanical refinements in shaft-drilling technology. The author traces the history of the equipment and methods employed by the large-diameter shaft-drilling industry and explores the likely paths of future development. Case histories that illustrate the adaptability of shaft drilling as a versatile tool for advanced, worldwide mining operations are cited. Safety, scheduling, costs, environmental impacts and capabilities are discussed.

Jan 1, 1996