Search Documents

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By Lindsey Schneider, Steve Kirk, Michael Miglioretti, Jeffrey P. Kolzow, Kyle White

The US17 Spring/Fishburne Drainage Improvements Project utilizes a stormwater conveyance tunnel system of approximately 8,250 LF. The tunnel system includes two intersecting tunnels of differing diameter at a 40-degree angle. The intersection was constructed in soft-ground conditions. This paper discusses the design, geotechnical concerns, initial ground support, and final lining construction. The tunnels utilized two soft-ground TBMs excavated at 15 ft and 11 ft with ribs & lagging initial support. The final lining consisted of unreinforced and reinforced cast-in-place concrete with polymer fibers. Concrete final lining was successfully completed in March 2020.

Jun 13, 2021

By D. A. Stanley

Researchers at BCD Technologies and the University of Alabama have applied three statistical techniques to the information contained in a large database of measurements from a phosphate ore processing plant. The rust, Principal Components Analysis (PCA), replaces many measured variables with a few fundamental and un-correlated variables. The second technique, Projection to Latent Structures (PLS), is an extension of PCA that explores the relation between variables identified as either independent or dependent. The third technique, Cluster Analysis (CA), is applied to the results of the PCA or the PLS calculations, and identifies individual data clusters that represent uniform operating conditions in the plant. All three statistical methods can be seen as geometrical operations on the data viewed as points in space. A Viewer gives a corresponding graphical presentation of the data points. This paper describes the use of the above three techniques and the Viewer to explore part of the phosphate flotation database.

Jan 1, 1998

By Donn W. Leva

In North America, pipelines move more material than any other form of transportation. 1 Pipelines have been used principally for the transportation of liquids and gases; however, slurry pipelines have made notable gains in recent years enabling solid materials to be moved efficiently by pipelines. The obvious advantages of pipe-lines --low maintenance, low operating costs, minimal impact on the environment, greater land use, low labor intensity, safety and high operating factor --have stimulated researchers in England, West Germany, Japan, USSR and the USA during the past ten years to develop pneumatic capsule pipelines for the movement of bulk materials in large quantities. As a result of this work, pneumatic capsule pipelines are now available for the movement of dense bulk materials. Through these pneumatic capsule pipelines, material is moved in wheeled capsules which are pushed through the pipeline by flowing air. In this paper, a capsule pipeline system developed by the Georgia Institute of Technology and Tubexpress Systems, Inc. of Houston, Texas is discussed. The Tubexpress System Major Components The pipe used for a Tubexpress capsule system is standard thin wall welded steel pipe. Since pressures in the system generally do not exceed one atmosphere, the controlling design criteria for wall thickness of the pipeline is pressure from the overburden of the backfill if the line is buried or the structural requirements for supporting itself and the load if it is suspended or supported on piers. The air pumping system for Tubexpress is a combination of

Jan 1, 1977

By T. McCallum, B. Wellbrook, T. Ratnaweera

"Pressure oxidation (POX) leaching of copper (Cu) concentrates continues to be explored as the next generation of leaching processes to sustain existing Cu Solvent Extraction/Electrowinning (SX/EW) operations as easily leachable ores become scarcer. The leach liquors produced, particularly from total pressure oxidation, contain elevated concentrations of Cu and acid, making solvent extraction processing more challenging. Addressing this challenge will require innovative processing techniques and continuous improvement to be successful in achieving satisfactory physical and metallurgical performance in the SX plant. The ability to efficiently process these feeds via SX plays an important role in the continued success of POX technology. Characteristics of a concentrate leach pregnant leach solution (PLS) are discussed, along with best practices that should be considered for processing by SX. Findings discussed in this paper will shed light on ways to reduce process risk and bring additional improvement to the industry with minimal change to the SX plant. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electro refining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges. The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile. The experience related to the current paper centers around Cu concentrate leaching performed by Freeport McMoRan (known as CLP). The patented process was developed as an alternative to smelting and refining in 1998. The technology applies to both molybdenum and copper concentrates. Commercial CLP research and development began with Phelps Dodge in 1999 to 2001. The first commercial plant was commissioned in 2003 at the Bagdad operation. Initial operating conditions of the Bagdad CLP were under high temperature conditions before converting in 2005 to medium temperature conditions. In 2007-2009, the CLP technology was commissioned in Morenci, operating medium temperature and high temperature lite conditions until shutting down due to the economic downturn. The Morenci CLP restarted operation in April 2015 due to acid production benefits for the Morenci leach operations. Renewed solvent extraction test work initiated well before restart and has been an ongoing focus for further SX plant optimization."

Jan 1, 2018

By Bob Snashall

"We could blow that damned fort out of existence if we could run a mine shaft under it!," claimed one Union soldier eyeing Bobby Lee's Petersburg defense line protecting Richmond and Jeff Davis. Puncture the line, take the hill behind, and the Confederate capital would celebrate Yankee jubilee, 1864. That was June. At 4:15 am, July 30, mine boss Henry Reese, sergeant, 48th Regiment, Pennsylvania Volunteers, gingerly entered the mine, dark and muddy. Something had gone wrong. The mine, set to go off at 3:30, hadn't exploded. It had to be checked. The main mine gallery, 1.5 m high x 1.4 m wide (5 x 4 ft) narrowing at the top to 0.6 m (2 ft), forced Reese into a tuck run. Some¬where up there in that 155 m (511 ft) stretch running 6 m (20 ft) under the rebel works, moisture may have doused the charge. Or maybe a fuse splice went awry. Or maybe there was live fire steaming like a locomo¬tive towards 3.6 t (4 st) of black powder. Perhaps now Reese wished this sprint was shorter. For the mine boasted a record break¬ing distance in military annals. Lieut. Col. Henry Pleasants Credit goes to Lieut. Col. Henry Pleas¬ants, commander of the 48th, who overheard the soldier's claim for what a mine could do. In peacetime, Pleasants had been a railroad engineer working on the Sand Patch Tunnel. He later switched to mining, working for the Philadelphia & Reading Coal & Iron Co. He even married the daughter of the editor of The Miners Journal. Grieving over his wife's early death, Pleasants plunged into the ven¬ture of war. This Union officer took the mine idea to the brass. Headquarters was less than enthu¬siastic. "The chief engineer of the Army and the rest of the regular Army wiseacres said it was not feasible," Pleasants wrote to his uncle. The pros scoffed, ticking off a list of horribles: No mine has ever gone that far, men will suffocate and be crushed, the rebs will countermine, the men will be trapped. Still, Pleasants eked out a signal to proceed. In the meantime, the miners of the 48th had commenced to dig anyway. It was like the 48th to proceed against the odds. The 48th Pennsylvania Volunteers The 48th had been recruited from Penn¬sylvania's Schuylkill County, anthracite coal mining country. The mines had been torn with strife over wages. Strikes and rioting were prevalent. Murder was not unknown. This "Buckshot" resistance centered in Pottsville, PA. It forced the governor to call in troops. Coal was in high demand to run the war machine. Pennsylvania operators worried that a military draft would stir up violence, closing the mines altogether and further shift¬ing business to emerging Illinois mines. Men lit out for the western gold fields in the tens of thousands. Secret societies bred in the mining camps invited draft agents to dance at the end of a rope. Jobs threatened by cheap, victorious South¬ern labor were one warning intended to get immigrant miners interested in the war. Operators gave miners time off to help de¬fend Philadelphia during Lee's thrust to Gettysburg. Even so, the draft spawned new violence and troop intercession. Soldiers were not welcome. The dust had barely settled when into this Pennsylvania "minefield" marched the 48th on a recruitment drive. The 48th had been in Lexington, KY on guard duty. When it came time for the regiment to pull out, the townspeople had prevailed upon authorities to extend the regiment's stay. Finally ordered to move out, the 48th was feted by a hanky-waving, tear-dropping send-off to the lyrical lament Auld Lang Syne. And Kentucky fancied itself to be rebel. Striding smartly into the Pennsylvania coalfields, the 48th attracted 400 recruits and marched off under regimental colors specially made by the proud citizens of none other than Pottsville, PA.

Jan 1, 1989

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By L. A. Weakly

The requirement for large diesel equipment to be certified for operation in potential gassy mine conditions in western oil shale mines motivated a design engineering project to develop a dry exhaust conditioner system to replace traditional wet scrubber technology. A dry exhaust conditioner for a 600 hp diesel engine was designed and fabricated for retrofitting into a 600 hp underground haul truck. The engine conditioner package was taken through a simulated certification process at the Mine Safety and Health Administration (MSHA) Approval and Certification Center to refine test procedures and to uncover any flaws in the dry exhaust conditioner technology. The engine/exhaust system was then installed in an underground haul truck to demonstrate mine-worthiness of the system. No inherent features were discovered that would prevent the system from meeting test requirements. However, the tests did point out several deficiencies in the prototype design.

Jan 1, 1989

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By D. A. Newman

The accurate prediction of mine profitability is essential for success in the present minerals market as is the ability to quantify the influence/of variations in revenues and costs on cash flow. A menu based spreadsheet template has been developed to determine annual cash flow, maintain depreciation schedules, and estimate labor and operating expenses. Sensitivity analyses may be conducted to determine the effect of productivity upon mining costs and the effect of selling price escalation upon rate of return. The advantage of this approach is that it can be used by a wide variety of professionals without extensive computer experience.

Jan 1, 1988

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By S. Yuan

A large-scale work scheduling algorithm has been developed in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. This study basically concerned the formulation of a reliable mathematical programming model to handle the problem, the achievement of an efficient solution of the model, and the implementation of the algorithm to the worker assignment problems of a large underground coal mine. The results showed that the work scheduling algorithm can make optimal assignments efficiently. It is believed it has potential significance in improving manpower utilization and can offer great help to coal mine managers in making efficient manpower allocations.

Jan 1, 1994

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By Bahaa Alyosif, Turan Uysal, Muhammet Kürsat Aydemir, MURAT ERDEMOGLU

 The paper investigates the effect of intensive milling on the conversion of microcline to potassium chloride during chlorination roasting. The study aims to improve potassium recovery by reducing the chlorination roasting temperature through mechanical activation.

Aug 1, 2023

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993