Search Documents

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors in¬fluencing the variation in face emissions between the two mines will be discussed.

Jan 1, 1997

By J. C. Rhodes

The demand for good white minerals for many industries including paint and plastics have made it necessary to import high grade industrial minerals from various parts of the world. Some of the calcium carbonate, barite and talc minerals are from China, Mexico, Jamaica and Haiti. These materials can be processed by custom processors. The custom processor can provide a service to the Industrial Mineral owner. The imported materials can arrive in various feed sizes from lumps (3"-6") down to 325 mesh. The materials can also be in various size shipments or container loads. The economics for importing should be investigated thoroughly. The two factors just mentioned can influence the quantity of material to be processed. These two factors can also influence the total cost for each end product.

Jan 1, 1989

By Duk-Won Park

A new gage for monitoring fractures in underground openings was successfully developed utilizing the reflection photo-elastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so that remedial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by the use of rubber backing. Crack growth as little as 0.003 inch up to as much as 0.1 inch width were detected in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in the laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1982

By Y. Luo, S. S. Peng

Based on the concept of slope-stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain is proposed. The slope geometry and the physical and mechanical properties of the soil at the surface of the natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach for the study of ground movement in hilly regions.

Jan 1, 2000

By Dan Nilsson

INTRODUCTION There are many mine planning factors in sublevel caving, as in the other mining systems, which when varied can substantially alter mining costs and profit¬ability. In this chapter, the following four topics are addressed with regard to economic optimization of sub¬level caving: production planning, haulage level spacing, orepass spacing, and extraction cutoff. The costs used here are the right order of magnitude but since each mine is unique, they should be considered only as examples. The objective is to demonstrate the tech¬niques which can be used. In a real mine, the evalua¬tions must be done using actual costs and conditions. It is difficult to predict exactly the costs involved, and therefore it is valuable to perform a sensitivity analysis to evaluate the effect of making incorrect as¬sumptions. Since the mining industry is very capital intensive, the effect of the interest rate must also be studied. PRODUCTION PLAN FOR AN IRON ORE DEPOSIT Introduction The first and most important thing to do before de¬signing an underground mine is to establish a long-range production plan. Such a plan is necessary for all eco¬nomic evaluations and should provide information about the lifetime of the mine, how much ore and waste must be handled per year, how much development per year is required, etc. An example is given in the following section. Problem In an iron ore mine sublevel caving is used. The iron content is 42%, and the mine supplies a pelletizing plant with an annual capacity of 3 million t/a. The ore body is shown in Fig. 1. The length of the ore body is 1000 m and the width is 100 m. Each slice is 10 m high, and there are 10 m be¬tween crosscuts, each of which has an area of 20 m2. The density of the ore is 3.5 t/m3. The spacing between rings is 2 m, and the extraction is 100%. The iron con¬tent is 66% in the pellets and 6% in the tailings. The problem is to develop a detailed production plan. A typical sublevel caving sequence is shown in Fig. 2. Solution Amount of ore per meter of crosscut: 20 X 3.5 = 70 t. Number of crosscuts per slice= 100. Length of crosscuts per slice: 100 X 100 = 10 000. Ore from crosscuts per slice = 10 000 m X 20 m2 X 3.5 = 700 000 t. Number of sublevel caving rounds per slice: 10 000/2 = 5000. Area for each blast in sublevel caving: 10 X 10 - 20 = 80 m2. Amount of ore per blast: 80 m2 X 6 m X 3.5 = 560 t. Extraction: 100% (see extraction curve Fig. 12). Loaded ore per blast: 75% or 420 t. Loaded waste per blast: 25% or 140 t. Total: 560 t. Total amount of rock from each blast in the sublevel caving: Ore: 560 t of which 2 X 70 = 140 t from develop¬ment work and 420 t from sublevel caving. Waste: 140 t. Total: 700 t. The ore needed per year is 3 X (66-6)/42-6 5 mil¬lion t. Necessary number of blasts per year= 5,000,000/ 560 = 8929. Distance to develop per year = 8929 blasts per year X 2 m per blast 17 858 m. Total amount/year: Ore from development work 17 858 m x 70 t/m = 1.25 million t/a Ore from sublevel caving: 8929 blasts per year X 420 tons per blast = 3.75 million t/a 5.00 million t/a Waste rock dilution: 8929 blasts per year X 140 tons per blast 1.25 million t/a Total amount to hoist 6.25 million t/ a The amount of ore from development work will in¬crease a little if the horizontal drift is placed in the ore body and not in the footwall. In this example the ore loss in 20%, and the waste rock dilution is also 20%. After taking the ore loss into account, the lifetime for 100 m of the ore body will be:

Jan 1, 1982

By Mark J. Schultz, William J. Francart, Gary J. Wirth

Atmospheric Monitoring Systems (AMS) utilizing carbon monoxide sensors have demonstrated their superiority over thermal type fire sensors for early fire detection in underground coal mines. After proving their capability and dependability throughout the 1980's, systems are now evolving and applying new technologies to enhance their effectiveness and reliability. The use of AMS in coal mines which utilize diesel equipment presents unique obstacles. Exhaust gases from diesel equipment not only raise mine ambient CO readings, but also cause numerous nuisance alarms. Both of these conditions reduce the effectiveness of the AMS. New technologies, such as discriminating devices, smoke detectors, and time delays, as well as administrative controls, have been developed and are being utilized to help reduce nuisance alarms produced by the diesel exhaust. This paper will discuss these technologies and administrative controls which are being utilized in coal mines to enhance the effectiveness of the Atmospheric Monitoring Systems. Reference to specific products does not imply endorsement by the Mine Safety and Health Administration.

Jan 1, 1995

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

By S. Gupta

Froth flotation is a process commonly employed for the selective separation of phosphate from unwanted mineral. Column flotation has become widely accepted in the mineral processing industry, including phosphate industries, due to its ability to improve selectivity, lower operating cost, lower capital cost, and superior control. In this work, a hybrid model is developed that combines a physicochemical model with artificial neural networks. The physicochemical model is based on axial dispersion with first order collection rates. A new approach, in which both frankolite (the desired mineral containing phosphate) and gangue (undesired product) are modeled, enables prediction of grade of the recovered product. Thus, two basic parameters are required in this model: flotation rate constants for frankolite and gangue. Artificial neural networks are used to predict flotation rate constants. The model also takes into account the particle size distribution and predicts grade and recovery for each particle size range. The model then combines grade and recovery for each particle size range to determine the overall grade and recovery of the column. The model is validated against laboratory column data.

Jan 1, 1998

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By James R. Taylor

24.1-BASIC PRINCIPLES JAMES R. TAYLOR The basic principle involved in maintenance is protection of a company's investment through the care and upkeep of machinery and equipment, buildings and properties. Maintenance is justified through making available to the maximum extent possible the facilities, machines and services required by the operating and production departments in their function of insuring optimum return on investment. As the size, cost and complexity of the equipment used in modern mining and related industries increase, operating and production personnel become proportionately more dependent upon maintenance engineering for its contribution to the overall profit picture. A greater part of the total cost now is charged to maintenance and the maintenance group becomes a major company unit. Basic maintenance concepts have changed very little over the years, but the advances in methods and technique have brought about tremendous challenge and have in consequence assumed a greater influence and importance. The older "sledge- hammer" methods have given way to engineered and scientific systems, while the accelerating development of intricate equipment and machinery, and the instrumentation essential for control, demand an ever-increasing upgrading of maintenance personnel. Regardless of this growth in importance, cost and complexity of the maintenance function, it is important to remember that it is not an independent and self-sufficient unit, but is a necessary facet of the entire plant operation and is subject to the company's total production effort. As one part of a team, maintenance is successful only when functioning cooperatively wit11 the other departments it serves Close collaboration in all areas served by n maintenance group is essential if it is to function fully to protect the company's investment, whether the assets are in machinery, materials or people. 24.1.1-MAINTENANCE SCOPE Maintenance functions may be grouped into the two general classifications of primary and secondary. This grouping constitutes a basic division although, in practice, the scope of the maintenance activity varies in each mine or plant and is subject to differences in size and type of operations and company policy, plus the influence of precedent, which may be sectional or industry-wide. The primary functions supply the justification for the maintenance engineering department. while secondary functions are variable according to plant conditions and needs. The primary functions may be categorized as follows: 1. Maintenance of existing machinery and equipment. 2. Maintenance of existing buildings and grounds. 3. Inspection and lubrication of equipment and machinery. 4. Utilities generation and distribution. 5. Alterations to existing equipment and facilities. 6. Installation of new equipment and facilities. 7. Instrumentation.

Jan 1, 1973

By Gerald P. Kelton

Hydrocyclones have emerged as successful classification devices In closed circuit grinding applications However, their use for ultrafine particles separation is a relatively new application For ultrafine particles separation In small diameter (51 mm or smaller) cyclones, the cyclone diameter, feed pulp density or viscosity, pressure drop, and configuration play an important role Most often commercial application of the small diameter cyclones suffers from plugging problems resulting from the presence of fibres, wood chips, paper scraps, etc This paper describes important design features of small cyclones, followed by examples of case studies of commercial application of these cyclones

Jan 1, 1983

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By B. M. Flohr

Railroads are cost competitive with trucks for hauls greater than 500 miles - WRONG. Today I will tell you about many rail movements of less than 100 miles throughout the country. Rail is a short haul transportation alternative you must consider. Transportation today is the largest controllable cost in the total cost of production of goods. In fact it is the one cost area where aggressive management, using new tools, can achieve significant reductions. You can't control the price of metals in the world market, you can't control labor rates since they are tied to industry norms, and the price of raw materials are relatively insensitive to specific price reductions to your firm. Transportation is the one area where major savings are now being realized. Sample Movements First, I will give you several examples of short haul rail moves to make you a believer that they do exist. Then I will show you the reasons why railroads suddenly "like" short hauls.

Jan 1, 1986

By Stephen H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, New Mexico area. The first four shafts sunk at international Minerals and Chemical Corporation's property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 Shaft there has been extensive-erosion and salt dissolution in the Rustler Formation which has led to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows it was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be codified to reflect any new or additional information which is obtained during the progress of the grouting.

Jan 1, 1984

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987