Search Documents

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By Ethan B. Eilertsen

Titanium solves corrosion, maintenance and environmental problems in many reactor and autoclave applications. Titanium clad construction permits autoclave designers a great deal of flexibility combined with significant cost reduction. Titanium alloys can be selectively applied in specific regions of the autoclave to accommodate local environmental conditions. Resistance to general corrosion, crevice corrosion, abrasion, and ignition conditions can be accomplished selectively and economically. Explosion clad pressure vessel fabrication and performance have been proven through three decades of experience.

Jan 1, 1997

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

NTRODUCTION Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for pre¬dicting the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface move¬ment data, a relatively large portion of the subsidence data col¬lected could not provide information other than surface movement. In a paper by Luo and Peng (1992), the sources and magnitude of errors in the measured surface movements using an electronic total station in subsidence survey are discussed. If the errors in the measured surface movement components are left untreated before calculation for deformation indices (i.e., slope, strain and curva¬ture), the errors will be carried over to the deformation indices and enlarged if improper numerical procedures are used in the calcu¬lation. It should be noticed that in protecting structures affected by ground subsidence, accurate surface deformation indices are much more important than surface movement. In order to improve the accuracy of the collected surface movement data and the calcu¬lated deformation indices, a number of numerical procedures are also proposed in the same paper. The proposed techniques include: a data smoothing technique for data pre-processing; and a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data. DATA SMOOTHING Because of various factors, the measured surface movement data always contain errors, small or large. In order to better utilize the collected data, a data smoothing method is proposed to correct the errors in the measured movement data. The method uses the same concept as the influence function method (e.g., Knothe, 1957) on which many existing subsidence prediction methods are based. The data smoothing method makes necessary corrections on the measured movement for the point of interest according to not only the measured movement at this point but also those at the surrounding points. The contribution of a surrounding point in making the correction for the point of interest is inversely propor¬tional, in exponential form, to the distance between them. The new magnitude of a movement component at the point of interest (Zi*) is calculated by

Jan 1, 1992

By Charles Bruce

Three years ago, at a reception given during the Steel Institute meeting in New York, I heard the remark, "A new formula must be found for foreign investment." This was immediately following the takeover of U. S. Steel's Matilde operation in Bolivia. Recently, at the World Mining Congress in Lima, Peru, the subject of foreign investment was still a lively topic of conversation. The nationalization of the copper mines in Chile and recent trends in the "Third World" have made all but a few extremely wary of investment anywhere other than in the ?stable? countries. Now, the fallibility of this philosophy has been demonstrated in such "stable" countries as Canada, Australia, and Ireland. Yet, nationalization is not new to us. The events in Chile were classified as disastrous to the affected companies, but so were the effects of nationalization to the majors in Bolivia in 1952. Mexicanization of the mining industry in Mexico was considered impractical by many. Now, those who accepted it are finding it to be workable.

Jan 1, 1975

By C. F. Curry

In the early 1940's Humphreys Mining Company in Florida pioneered heavy mineral mining with a dredge in the United States, In 1948 Du Pont, in conjunction with Humphreys, opened their first of two mining operations recovering a titanium dioxide product in Florida. Later on in 1952 Du Pont opened their second plant, both of which used a cutterhead suction type of operation. This process is also used in heavy mineral mining in Australia and Africa. In 1957 ASARCO started prospecting in New Jersey. Test borings indicated a large deposit of ilmenite bearing heavy mineral sands had been deposited and concentrated in an area near Lakehurst in central New Jersey. Humphreys Mining Company was contacted about the possibility of mining the ASARCO New Jersey property in much the same way as Du Pont and themselves were doing in Florida. An extensive study was made to determine the economic feasibility of mining the ASARCO property. During this study, extensive test drilling and samples for a pilot plant were taken.

Jan 1, 1975

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By B. K. Gupta

Arch Mineral's Captain Mine has used the Bucket Wheel Excavator System(BWE) for over 3 years in conjunction with a 180 yd3 (138M3) stripping shovel. The bucket wheels prestrip the soft overburden ahead of the shovel. This soft overburden is brought to the spoil side through a series of shiftable conveyors and placed by a spreader over the ungraded or partially graded shovel spoils. The placement of the soft overburden and top soil is accomplished in a manner that meets the reclamation mandates. The prestripping by the BWE has reduced the incidence of the highwall and spoil slides, depth the stripping shovel has to dig and the volume handled by the pullback draglines.

Jan 1, 1984

By R. Mensah-Biney, M. T. Hepworth, K. J. Reid

The kinetics of gold-bromide loading onto activated carbon was investigated in a batch stirred reactor. Based on a second-order equation, the amount of gold adsorbed by the carbon was correlated with time. From a 30ºC solution containing 25 ppm Au and 0.8 g/L carbon, the rate constant for gold-bromide species onto activated carbon ranged from 0.27 x 10-3 to 1.2 x 10-3 (kg/t)-1 min-1. The equilibrium saturation capacity (Qe) was 36 ±3.0 kg/t from the same system. The rate of loading increased with increasing temperature and decreasing particle size, pH and solution gold concentration. The calculated activation energy (Ea) was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Qe) increased with increasing concentration of gold in solution but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1998

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By B. Denby, R. Hollands

Mine information is often multi-disciplinary, dynamic and spatially complex. Different departments use the same data in many different ways, information changes over time and mines change their shape continuously. Earthworks InTouch is a radical VR-based system developed by AIMS Solutions and marketed by Earthworks, which provides a rapid and intuitive interface to a wide range of mine information. VR is used to provide an interactive and visually accurate, dynamic 3D model of the mine workings and equipment operating in the mine. Individual objects in the mine can be linked to external applications that provide up-to-date and context sensitive information. Equipment movement can be simulated or tied in to real-time survey from GPS systems for example or excavator productivity data can be extracted from a production database. The paper will highlight the major advantages of using such a VR interface to access valuable and time sensitive information.

Jan 1, 2002

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By W. J. Douglas

Before discussing minicomputer software for the mineral industry, it is helpful to explain some of the computer program terminology. Most of the terms are the same as those applied to large computers. A computer system consists of a machine (hardware) with electronic and mechanical components and instructions (software) that define its operational logic and sequence. This logic is described by sets of commands grouped into programs. Each program has specific objectives related to the computer's operation and to production information from computer data that are input and processed. Software, therefore, is a general term applied to any type of computer program. Instructions to the computer are communicated through languages that convert logical and arithmetic statements into machine operations. The languages may consist of statements resembling mathematical or logical phrases understandable by humans, or they may be coded statements with no apparent resemblance to spoken language but readily understandable by the computer. Computers also translate higher level languages such as FORTRAN or COBOL into machine languages using other programs called Compilers. Programs written in these higher level languages are generally called source code. However, programs written in computer assembly language may also be called source code. The compiled version of the program after it has been translated by the compiler software is called object code. Programs used to "instruct computers how to be computers" are generally called systems software. They relate more to computer operation than to producing externally usable results. Programs producing information for many users-engineers, accountants, managers-are termed applications software. For the most part, applications software is the principal concern of the mineral industry. Programs are developed to fit user requirements as interpreted by programmers. Programs vary in quality, precision, efficiency, accuracy, and complexity, depending on programmer skills and abilities and programming decisions forcing design tradeoffs. A well written program should have speed, efficient use of available hardware resources, accuracy, and an inherently logical structure that aids documentation and subsequent modifications. Programs developed to fit specific requirements are termed customized software. A program organized and prepared for general commercial use is called a package, or a software package, and includes documentation for program use. A form of customized software that takes an existing program or package as its starting point and modifies it is called a customized package. A minicomputer program can be stored on computer cards, standard magnetic tape, magnetic cassette tape, floppy disk, or hard disk. The software purchaser or lessee may select one or more of these media when specifying a program in a software contract. Supporting documentation may include a listing of the program instructions linkages, hardware and storage resource requiremnents, flow charts, and programmer and user manuals. The purchaser must carefully make and clearly understand specifications for media and format of program delivery. This assures that delivered software is compatible with the intended hardware. Mineral Industry Attitudes Toward Computer Software The mining industry has traditionally been conservative concerning computer applications. Furthermore, large computer costs have made these systems accessible only to large companies, for the most part. But in the past few years, mining software systems developed at schools such as Pennsylvania State University and Virginia Polytechnic Institute have gained wider acceptance in the mineral industry. More mining engineers now have academic training in computer application, and computer use is now more acceptable to the mining industry. Mining managers in decisionmaking positions are faced with a new generation of computer technology resulting from the rapid evolution of minicomputers. Not too long ago, manufacturers such as Digital Equipment Corp., Data General, and Hewlett-Packard were considered newcomers. They are now established companies. In addition, Apple, Radio Shack, Commodore, and others have emerged in the growing microcomputer industry. So the mine manager or mining executive now has more options. Mining Software is Limited Along with the rapid evolution in hardware development, much general purpose software is now being developed for minicomputers. The 1981 Apple Software Directory can be obtained for about $14; Radio Shack published the Application Software Source Book in three volumes for $1.95 each. Brochures describing software can be obtained for other minicomputer manufacturers by contacting local sales representatives. Hewlett-Packard software can be obtained and exchanged through HP user's groups. Manufacturers' programming staffs are generally concerned with developing applications software. In some instances, manufacturers will recommend software developed by their hardware users. Until now, however, software development for mining applications has been minimal. This should not be surprising, since software development traditionally lags hardware development by several years. A review of A Directory of Computer Software Applications/Mini-Computers and Micro-Computers, August 1977-1980, published by the US Department of Congress, National Technical Information Service, contains many entries and subject areas. General applications include some references to tunneling machines, but there are virtually no entries specifically relating to

Jan 11, 1981

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By A. Geoffrion, L. J. Cousineau

In underground powerhouse excavations, the access to the horizontal sections of the penstocks is most often critical. Other factors which influence the schedule include: the sequences of excavation, the interface dates between contracts, the type of support for the overhead cranes and whether the roof in the powerhouse is a reinforced concrete arch or a suspended prefabricated material. At Outardes 3, Churchill Falls and LG-2, these factors, along with the size of the powerhouse and the local topgraphy and geology were studied to produce the optimum schedule.

Jan 1, 1983

By I. R. Miller

The purpose of this discussion is to try to offer some suggestions as to how the zinc and lead markets will perform over the balance of the decade, review some of the factors influencing production and come to some conclusions regarding prices. The past 2 years have been simply awful in terms of consumption, prices and overall profitability for the industry. In looking ahead to the year 2,000, it is probably not a bad idea to look back about 20 years to see where we have been and how we got to where we are. Zinc consumption from 1950 to the early 1970's increased steadily and rather nicely at an annual average rate of close to 4.0%. It was starting in the early 1970's that things started to get volatile and at times, difficult for the industry. The general economic boom of the early 70's was marked by annual consumption rates close to 5.0 million tons, a level not seen again for over 10 years. The First Oil shock of 1973-74 was followed by the sharpest consumption drop in memory. In two years, Western World zinc consumption fell 27%. While our chart shows a rather dramatic recovery thereafter, the average annual growth rate since 1970 has only been a rather modest 1.5%.

Jan 1, 1992