Search Documents

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By Brian Burdett, Terry I. Mudder, Robert T. Richins, James A. Stevenson, Michael M. Botz, Alan L. Wilder

The first Cyanisorb process was constructed in 1991 at the Golden Cross Mine in Waihi, New Zealand to recover cyanide from CIL tailings. The Golden Cross operation consists of an open-pit and underground gold mine with a conventional crushing, grinding and CIL circuit with Merrill Crowe zinc precipitation for gold recovery. Prior to disposal in the tailings pond, slurry tailings are stripped of cyanide at a pH of approxi­mately 7.5 using the Cyanisorb process. Mill throughput is approximately 2,500 tons per day (TPD), and CIL slurry tailings average 37% solids with a specific gravity of 1.27. CIL tailings WAD cyanide average 150 mg/L. The Cyanisorb process recovers approximately 85% of tailings WAD cyanide, produc­ing a slurry effluent with approximately 20 mg/L WAD cyanide. A second Cyanisorb process was commissioned at the NERCO DeLamar silver mine in southwest Idaho in May, 1992. The ore milling and silver recovery operation consists of crushing, grinding, a CIP circuit and Merrill Crowe zinc precipi­tation for silver recovery. Cyanide recovery is from clarified tailings with WAD cyanide ranging from 3 50 mg/L to 600 mg/L, producing an effluent with less than 30 mg/L to 60 mg/L WAD cyanide. Due to the presence of zinc-cyanide complexes in mill tailings resulting from the Merrill Crowe process, cyanide is stripped at a pH of approximately 5.5.

Jan 1, 1995

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By Keith S. Liddell

he selection of mill design parameters to suit the applica­tion requirements can result in quite different operating parame­ters for each generic type of application, even though the basic mechanical layout of the mills may remain similar. The selection of the type and size of grinding media is very important to efficient and cost-effective operation, and to ensuring that the milled product achieves the required properties. Accordingly, the grinding media selection is seen as an integral part of the mill design. Consideration of the requirement for classification is important in order to achieve the optimum mill and circuit performance. This can lead to the circuit feed not being classified for a steady feed with minimal slimes and a low size reduction ratio. Feed containing on-size particles would be deslimed by open circuit classification. Closed circuit classification is performed where the feed fluctuates. The rheological characteris­tics of the circuit feed slurry can have an influence on mill performance, and needs to be allowed for. A common misconception frequently encountered is the belief that "a mill is just a mill". This is not the case with stirred types of mills, since the operating parameters selected for the mill can have a large effect on the product characteristics. For example, horizontal shaft high speed stirred mills have a com­pletely different grinding action to vertical shaft low to medium speed stirred mills, which results in large differences between the surface area produced at a given product size (Liddell, 1986). Hence, it can be misleading to apply test results or design procedures obtained from one type of mill to other types for scale-up. The Metprotech stirred mill, as applied in the mining and minerals industries, is a low to medium speed vertical shaft mill. The basic design has been discussed previously (Liddell, 1989). Currently, the largest mills that have been manufactured have an installed power of 400 kW. The largest chamber volume at this power is 6000 litres, containing IO t of grinding media. It is intended that the installed power will increase up to lMW as applications requiring larger sizes arise.

Jan 1, 1995

By Norbert Patzelt

The high-pressure grinding roll was introduced about 10 years ago and has established itself in many applications. Most of these machines are used in grinding circuits in the cement industry. A few operate in conventional mineral-processing plants. Polysius has sold more than 350 Polycoms worldwide. An exception is diamond-ore processing in South Africa and Australia. This type of grinding system increases diamond liberation and reduces the capital costs for the downstream processing plant. There are several reasons why high-pressure grinding rolls have not been used more extensively in the mining industry: - The mining industry adheres to conventional grinding technology and regional preference for certain comminution circuits. - Design, scale-up and flowsheet assessment procedures are viewed as being immature and reduce confidence in the potential application of the technology. - Downstream process benefits are unproven on a plant scale.

Jan 1, 1995

By D. A. Stanley, B. J. Scheiner

The Bureau of Mines, US Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1990

By B. Gorain

"INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Keywords: Digital Transformation, Operational Intelligence, Gold Recovery, Mine to Mill integration, Planning and Execution strategy, Theory of Constraints. Challenges Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance. Consequently, over the last few years, there has been a major focus amongst some mining companies to imbibe Operational Excellence. This has been only possible because of the replacement of a silos based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organization is not trivial. Attempts in the past to integrate functions such as through Mine-to-Mill initiatives in the mining industry have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turn over and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate.Opportunities The advent of digital technology has opened-up opportunities to integrate inter-departmental information for a unified understanding of, and across, an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/Historian) and industrial networks have helped in the direction of enterprise wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan & Gorain (2016), some of the potential opportunities are as follows:"

Jan 1, 2018

By John R. Riede

The use of radioactive gages in beneficiation plants is relatively new However, enough applications have been made so that it is now possible to positively state that these gages have definitely progressed from a laboratory device to a very rugged and reliable on stream process measuring instrument. Gamma Ray Gages of the type presently being used in the beneficiation industry consist of three basic components: (1) A source of radiation (2) A radiation detector (3) An electronic amplifier The source is usually a radioisotope such as cesium-137, or cobalt-60. This source, adequately protected and ruggedly mounted, is most commonly placed on one side of a pipe or vessel. The radiation detector is then mounted on the opposite side, Since the absorption of gamma radiation as it passes through various materials is a function of the density of the material, the change in radiation measured by the detector is proportional to the change in specific gravity of the product in the pipe or vessel. One popular type of detector in use today is a cell which converts radioactive energy directly into electrical energy1. This electrical energy, when amplified, presents a usable output for metering and control devices. There are, of course, many other components which are part of a working gamma gage installation, such as zero compensators, lead shielding, mounting brackets, equivalent absorbers, etc.

Jan 1, 1958

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines&apos; program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau&apos;s continuous residue processing plant, College Park Metallurgy Research center.&apos; The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By W. R. Boehme

The test work was done in two parts. In Part I, five 6 x 16 mesh activated coconut shell carbon samples made by four different manufacturers were evaluated as to their gold loading rate and total gold loading. The five carbon samples tested are not identified by manufacturer and are simply designated as Types A through E. Then from the carbons tested, a suitable highly active carbon was selected for subsequent studies on impurity effects upon loading, Part II. Test Procedures The procedures and tests descriptions are given for the ultimate gold carbon loading tests and the dynamic gold carbon loading tests.

Jan 1, 1983

By W. L. Han, Y. D. Zhang, X. C. Li

Meta-systhetic technique for large systems engineering has been placed on the agenda. The meta-systhetic A1 approach should involve the integration of digital and knowledge info, from qualitative to quantitative analysis, etc. Some algorithms of meta-systhetic technique such as ANN-ES and GA-ANN are introduced. A case study follows - mining conditions evaluation by meta-synthetic A1 methods, including: setting up the structure of evaluation indexes system, deciding their grade of membership by ANN-ES algorithm; determining the weight values of evaluation factors by GA-ANN algorithm; and developing the integrated evaluation model.

Jan 1, 2002

By D. G. Krige

In the world mining scene, precious metals (particularly gold) have recently monopolized the attention in exploration as well as new production activities. As the major world producer of gold, South Africa plays and will continue to play a very significant role in this commodity. This role will, of course, have its consequential effects on the world&apos;s gold supply and, hence, also on the international price of gold. It is essential, therefore, and in the interests of all gold producers that the likely future pattern of gold production in South Africa be estimated such that some measure of production uncertainties can be predicted. For this purpose, some elementary geostatistical models will be used, and the main factors affecting the situation will be analyzed in broad outline only under the following headings: South Africa&apos;s basic gold ore potential in the three categories of: (1) ore remaining in existing mines; (2) extensions to existing mines via unexplored areas and/or reef horizons of lower grade; and (3) new mines, potentially deep or ultradeep. Cutoff grades - operating, marginal, and flotation, for the foregoing three ore categories, respectively. The availability of production, financial, and other resources required. Cutoff grades will, of course, depend on cost levels (operating and capital), future inflation and cost escalation trends in South Africa (SA), and/or gold price trends (in US$ and via the exchange rate in SA Rand terms). The differentials in inflation and escalation trends with those in overseas countries, mainly the USA, will, in general, set the scene for future exchange rate levels of the Rand. To predict the effect of various cutoff grades on future gold production from South Africa, it is essential to use geostatistical models. The applicability of such models is tested against past records of price, cost, and grade trends and then applied to the estimated ore potentials. These models were referred to briefly in a paper at a recent seminar on gold (Krige, 1986) but are discussed in detail herein. This lecture was intended originally to cover only technical aspects, but, in view of South Africa&apos;s position internationally and the possible effect of sanctions, internal unrest, and strikes on gold production, a brief reference to the third factor above (availability of production, financial, and other resources) seems appropriate.

Jan 1, 1988

By Patrick J. Doig

The Crosstown 7 Collector System, Contract C28G11, is part of the Milwaukee Metropolitan Sewerage District&apos;s Waste Pollution Abatement Program. The contract involves the construction of 1.6 km (1 mile) of 3 m (10 ft.) diameter tunnel in soft ground. The tunnel is 10 m (35 Ft.) below surface and passes through a variety of soils. The eastern leg of the tunnel along Bruce Street is mainly in till material, a stiff, relatively dry clay. The northern leg along 16th Street starts in till, and continues in estuarine deposits - moist sticky clay, with intrusions of alluvial sand and gravel. The contract specifications required that the tunnel be constructed either under compressed air or with an earth pressure balance tunnel boring machine. The S. A. Healy Co., the general contractor, chose the latter option. Additionally, a single pass, pre-cast concrete segmental liner was selected as the lining system. The mining machine was manufactured by Lovat Tunnel of Canada and the segments were made by the Sehulster Company of Milwaukee. The use of this combination of machine and lining is relatively new to the United States and this tunnel is the most extensive built to date with a gasketed, segmental single pass lining for transportation of fluids. This paper details the various aspects of the construction of the tunnel and associated shafts.

Jan 1, 1989

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023