Search Documents

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By John Drew Ridge

Recent work by Haas has made available information on densities and vapor pressures of solutions of differing salinities at temperatures up to 330°C. From these data it is possible to predict the behavior of volcanic exhalations of various degrees of salinity as they approach the sea floor. Particular attention is devoted to solutions of 5.0 weight per cent NaCl and 20 weight per cent NaCl, two fluids that approximate quite closely the salinities of what Roedder termed: (1) normal hydrothermal fluids and (2) fluids typical of stratiform deposits of low-temperature conditions of origin. It is apparent that solutions above 220-230°C. cannot reach a sea floor on which the depth of water is 600 feet or less in the liquid state but will boil at some appreciable depth beneath the sea floor. Such boiling would result in the precipitation of all constituents of the ore fluids of significantly lower vapor pressure than water. The principal such constituent would be salt, and no sulfide deposits, the major constituent of which is salt are known. It follows, therefore, that ore fluids probably never get close to the sea floor of shallow seas at temperatures high enough to permit boiling. Ore fluids significantly above 230°C. can reach the sea floor in the fluid state only if the depth of the sea in the area. in question is well above 600 feet, for example, solutions at temperatures of ±300°C. reach the sea floor in the liquid state only if the depth of sea water is slightly over 3000 feet. Ore fluids reaching the sea floor at such depths may be the parents of such fluids as the Red and Salton Sea brines. On the basis of these data, the Cyprus and Kuroko deposits are discussed.

Jan 1, 1973

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By Nicholas Tabor, Norbert Fuegenschuh, Richard Taylor, Jean-Marc Wehrli

The Plymouth Tunnel forms part of the 16-mile long route of the Purple Line Light Rail Project promoted by the Maryland Transit Administration. The tunnel is approximately 1,220 feet in length with a shallow vertical alignment located beneath a residential area. Challenging mixed ground conditions included surficial soils, decomposed Saprolite, and highly weathered to fresh rock requiring the use of the Sequential Excavation Method (SEM) for construction. This paper discusses innovative approaches implemented during construction as well as challenges faced during planning and installation of a spray-applied permanent concrete liner.

Jun 13, 2021

By Daniel Willis, Ryan O’Connell

An 8-foot tall horseshoe adit tunnel located within an abutment of the Mount Morris Dam in Mount Morris, NY required repair of a failed reinforced concrete liner. The adit tunnel is entirely founded within highly weathered shale bedrock units, which induced unloading stress on the original tunnel liner. An epoxy-impregnated carbon fiber fabric wrap manufactured by Sika was chosen to repair the failed adit tunnel liner. Kilduff Underground Engineering completed the design of the tunnel repair utilizing both empirical and numerical methods. Merco Engineering Contractors completed the injection of chemical grout and repair liner installation.

Jun 23, 2024

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By R. V. Ramani, R. Srikanth, R. Zhao

A two-part study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbodvolatile matter), Vitrinke Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.

Jan 1, 1995

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By W. Moser

During the ten year span from 1978 to 1987, the number of fires which occurred in under-ground coal mines doubled from the previous ten years. Anyone involved with underground coal mines is well aware of the associated tragedy that can result from these fires, both to personnel and to property. Every day mine management and mining personnel face this threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. As a direct result of the ever-increasing interest in the Mine Emergency Preparedness Program and the Mine Fire Training Programs currently being conducted, the Emergency Preparedness Center was created. As a branch of the Mining Extension Service at West Virginia University, the Center provides preparedness training at several different levels on a varying range of topics. Classes are conducted at a new especially-designed training laboratory at the National Mine Safety & Health Academy in West Virginia. By maintaining the proper equipment and levels of training allowing for immediate response, the personnel who are part of the Center believe that the impact of a mine fire or other such emergency situation can be minimized. This paper will present recommendations for maintaining an efficient mine emergency preparedness program and will provide information regarding the Mine Fire Training Program as conducted by the Emergency Preparedness Center and describe the advantages of the newly constructed training facility.

Jan 1, 1993

By Michael J. Nicol

Hydrometallurgical processes involve the recovery of metals from ores, concentrates, calcines, mattes and scrap materials by a series of operations involving leaching or dissolution, separation, purification and reduction of metals in aqueous solutions. The underlying theoretical basis of many of these operations is electrochemical in nature and it is the purpose of this review to identify and illustrate, by way of examples from the author's experience and that of others, the central role of interfacial electrochemistry in the understanding, design and control of these operations.

Jan 1, 1993

By P. J. Kientzler, Y. C. Lo

The current study is concerned with the analysis and attempt at simulating the product size distributions obtained from a vibrating ultrasonic device. Systematic experiments of comminution were performed with natural sizes as well as monosizes in order to understand the breakage behavior of the device. A precise analysis of the device's breakage performance in the case of fine grinding of alumina samples will be presented. Initial steps to model the breakage events using a detailed mathematical algorithm will be discussed.

Jan 1, 1992

By M. Bleeck

Calcium carbonate (CaCO3) is one of the most ubiquitous and versatile minerals found in the earth's crust. Its availability, attractive physical properties and relatively low processing cost make CaCO3 the most widely used filler material today. It is mined in three different forms - chalk, limestone and marble. Each physical form of CaCO3 has different qualities due to differences in postdepositional geology. But the chemical composition remains the same, with CaCO3 an inert component of the finished product. In the past, the paper industry largely left CaCO3 by the wayside, as it cannot withstand the acid-based papermaking process. But conversion to an alkaline system by many US mills changed this picture. Carbonate suppliers have put time and effort into research and development, demolishing barriers and creating new possibilities for what is a simple, natural product. By controlling particle size, size distribution and particle charge, the industry uses ground calcium carbonate (GCC) as a performance enhancer and as an extender for more expensive ingredients. It is estimated that the United States uses 3.6 to 4.1 Mt/a (4 to 4.5 million stpy) of CaCO3. Consolidations and mergers are taking place in the industry. Of the 12 major GCC producers in operation nine years ago, seven are left. Mineral Technology (US) is the dominant precipitated calcium carbonate (PCC) producer with more than 50 satellite plants worldwide. Other producers include Georgia Marble (French); Franklin Industries (US); OMYA (Swiss); J.M. Huber (US); ECC (English); and Filler Products (US). Global Stone PenRoc (Canada) is the only newcomer. In addition to this group, there are three small producers left in North America, each with a capacity of less than 100 kt/ a (.110,000 stpy). The trade organization operating as the Pulverized Limestone Division of the National Stone Association renamed itself the Pulverized Mineral Division, to increase its membership pool. The US paper industry is a predominant GCC con¬sumer, using approximately 800 kt/a (882,000 stpy) at an approximate cost of $130/t ($1.43/st). European paper mills pioneered alkaline papermaking. In the early 1960s, they began using GCC as filler and soon thereafter added GCC to their coating formulations. A decade later, the North American paper industry followed suit. The conversion from acid to alkaline paper production benefits the economic and performance aspects of the industry. Less pulp is needed, paper machine maintenance and effluent treatment costs are reduced, and sheet strength, opacity and brightness are increased. Perhaps most important to the reader, the sheet is desensitized to ultraviolet light, extending the paper's archival ability. CaCO3 can provide the papermaker with additional control of his paper. For example, PCC has long supplied the tobacco industry with a means to slow down the burning rate of cigarettes. Due to enhanced performance with regard to bulk and opacity, filler PCC use has risen to 1,500 kt/a (1,650 stpy) in the United States, at an approximate price of $130/t ($143/st). The majority is produced onsite at the paper mill, using "satellite plants." This concept reduces freight cost because only quicklime (CaO) is shipped to the mill, not CaCO3 slurry. The future of CaCO3 is encouraging. The amount of natural ground CaCO3 used is expected to double by the year 2005 to approximately 8 Mt (8.8 million st) worldwide. Acid papermaking practices will feel an increasing pressure to convert to an alkaline process as larger volumes of GCC containing paper enter the recycling market. CaCO3 reserves are plentiful. They will supply the ever growing demand for increasingly sophisticated paper. The plastics industry is supplied with almost 900 kt/ a (990,000 stpy) GCC at an annual growth rate of 4% to 5%. The price of a functional, inorganic filler, surface modified for the plastics industry, has an average selling price of $220/t ($243/st). GCC represents the most common filler, creating a product with higher gloss, better dielectric properties, impact resistance, weatherability and shrinkage control. CaCO3-filled plastics surround us - auto hubcaps and dashboards, shower enclosures, floor tiles, wire coatings, microwave dishes and Tupperware. The caulking and sealant industry is an enormous GCC user, with annual consumption requiring 1.13 Mt (1.2 million st) at about $44/t ($48.50/ st). Caulking and sealant may be highly filled with GCC yet undergo no adverse flow effects, with a narrow particle-size-distribution filler decreasing the binder demand. The CaCO3 industry, as well as the carpet industry, are more or less tied to the growth rates of the construction industry. It is estimated that the carpet industry uses some 680 kt/a (750,000 stpy) of GCC at about $25/t ($27.50/st). The paint industry uses approximately 300 kt/a (331,000 stpy) at a 1 % to 1.5% annual growth rate. Here, too, GCC is the dominant filler. It is used to enhance flow characteristics and color uniformity. It also extends costly titanium dioxide, creates sheen and controls roughness, hardness and tack. More CaCO3 should be used in the future as industry shifts from solvent-free or water-based formulations that can accommodate higher GCC volumes. CaCO3 is not imported or exported in any great quantity. Most areas have reserves of their own and the selling price is relatively low. Even so, quality varies from deposit to deposit. As our needs become morespecific, it remains a challenge to provide varying industries with a fitting product.

Jan 1, 1998

By Erica Frederickson

"Millennials. Doesn’t the word just make your blood boil? You’ve probably encountered one of those kids who think they know best despite a lack of any real experience.Hi, my name is Erica, and I am a Millennial. We often get a bad rap, sometimes for good reason. But we do have qualities that are often overlooked. For example, I am happy to share with my generation a real desire to make a difference in the world and a commitment to innovation. Does this mean I think we always have good ideas? No – especially not right away. After all, few of us came anywhere near a piece of construction equipment until arriving for our first job, as was the case for me. We may have fancy degrees, but not many of us learned to run a jackleg drill in school.Two weeks after graduating college in 2011, I packed up my bags and moved to New York City to work as a field engineer for Traylor Bros. Inc. on the Queens Bored Tunnels project (Granite/Traylor /Frontier Kemper, JV), part of NYC MTA’s multi-billion dollar Long Island Railroad East Side Access project. It was here I became acquainted with the notorious New York City union workers. Perhaps the greatest challenge of my career thus far was earning the respect of the field supervision and craft workers on this first project.The first time I asked a maintenance mechanic to clean a piece of equipment in accordance with our maintenance protocol I got a flat-out “No.” It was the most powerless I had ever felt. But why should these experienced workers trust a 21-year-old girl with her civil engineering degree and no prior experience? I realized no employee on the job had any reason to listen to me — not until I proved my worth. Fortunately, I arrived on the job site just as we were commissioning the slurry plant for the first tunnel drive. I dove into learning as much about the slurry tunneling process as possible and was able to quickly pick up the ins and outs of running the slurry separation plant. As none of the other engineers or management had first-hand experience on a slurry tunneling job, I soon became the go-to engineer in the slurry plant. No one questioned me if I asked to have something done around the plant after that, or if they did, they quickly learned that I had a convincing answer as to the need for the task. I was even able to play a large role in shaping our slurry monitoring and control methodology."

Jan 1, 2015

By W. Baguley, L. P. H. Greenhalgh, R. P. Riley

The traditional impeller system for aeration and suspension of slurries, e.g. in bacterial oxidation plants, is the vertical flat blade turbine (VFBT) . This type of impeller is energy-intensive, which results in a heavy-duty design of shaft, gearbox and drive. The Mixtec BX04 agitator development programme is designed to evaluate the use of the new generation of hydrofoil impellers which consume less power and thus have potential for capital and operating cost savings as well as being possibly less damaging to the bacteria. The early tests on pyrite oxidation in a 300 litre laboratory pilot tank using the Thiobacillus ferro oxidans bacteria, showed that hydrofoil impellers had superior characteristics to the VFBT impeller and to air-agitated pachucas, with lower energy input. The geometry of the air sparge ring was found to be very important in optimizing the system. These early successes resulted in a prototype impeller and sparge ring beinq tested in a 9m3 tank where oxygen uptake in water, impeller cavitation at different impeller speeds and air flows were evaluated. Resulting from this work was the supply of an agitator unit to an operating bacterial oxidation plant where it has been successfully evaluated. This paper describes the development work so far carried out

Jan 1, 1992

By B. P. Atkin, D. W. Brown

The handleability monitor has been specifically designed to provide a simple, rapid and on-site assessment of the whole or part consignment of a coal blend in its ‘as-received’ condition. Evaluation has been carried out at a number of coal-handling plants, on both metallurgical and power station coals from a variety of sources world-wide. The results which are used to predict which coals could routinely pass through a handling plant at line capacity, without causing blockage or delay, have also been correlated with moisture, ash and size analyses of the coal to develop a predictive model of handleability.

Jan 1, 2000

By George J. Bujtor, Anthony K. Scott, Haddon F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1992