Search Documents

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Jerry M. Whiting

Greater awareness of the increasing need to develop supplementary energy sources is accelerating us towards many basic decisions regarding future utilization of mined energy materials -- uranium, coal, oil sands and oil shale. The latter material comprises a major potential source of oil which will require creation of unusually large and low-cost underground mining systems. In this paper, the author briefly outlines and analyzes several of the factors which continue to provide the somewhat unique character of oil shale nine planning and mine operation.

Jan 1, 1974

By Jorgen Elbrond

The calculation of open pit operations&apos; capacities has been the subject of many studies using computer simulations. The common problems of simulation are that if one desires a realistic picture of an operation the programming work becomes long and expensive and that the program requires a large computer and long time to run. The method presented in this paper overcomes these problems by using a straightforward calculation procedure. It is based on the queuing theory&apos;s simple formula for waiting time in a closed circuit and uses a system of correction factors, which reflect the loading, travel, and dumping times&apos; relative variabilities and which have been found by 1) mathematical analysis and 2) simulations of basic circuits. The method includes the main parameters of the operation: numbers, sizes and operational availabilities of trucks, shovels and dumping point, distribution of the production over shovels, trucks&apos; loading, travel (loaded and empty) and dumping times as well as their variabilities, shift&apos;s composition. The procedure models: the average duration of a complete truck cycle during stationary and non-stationary periods during the shift as a function of the number of trucks in the circuit, the composition of the average 100% operated shift, the simultaneous probabilities of operationally available shovels and trucks and the distribution of shovels and trucks according to production and cycle times. The procedure can be programmed for a small computer and requires only short computing time, which makes extensive studies of various parameter combinations practical to carry out. The development of the method is an extension of previous work by Morgan and Peterson {1}, who by simulation established the relation between the match factor (which is the ratio between the sum of one loading time pr truck in the circuit and the complete net cycle time) and the shovel&apos;s efficiency, and by Hayes, Splaine and Whitaker {2}, who established this relation from a large number of observations in the Nchanga pit in Zambia. The present method establishes this relation by a straightforward calculation procedure. Theoretical solutions to some situations are found in the litterature on the queuing theory. The papers {3},{4} and {5} give solutions to situations, which fall outside those encountered in the shovel-trucks circuit. These solutions together with simulations of in-termediary situations have been used to establish an interpolation procedure for the correction factors to be applied to the waiting time formula in order to cover the situations encountered in practice.

Jan 1, 1977

By Brianna Eiter, Max Barham, Tim Bauerle

While not well established, there is evidence that the mining industry is encumbered by several work-related fatigue risk factors. Compared to other industries, mine workers are more likely to report inadequate sleep and work longer hours per day. Given these observations, there is a critical need to identify effective ways to intervene, manage, and mitigate mine worker fatigue and sleepiness when present. One barrier to this is confusion around the similarities and differences between fatigue and sleepiness, which can result in these terms being treated as interchangeable regardless of context and make it difficult to assess and mitigate safety risk.

May 1, 2024

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By Mike Preston

Attrition scrubbers may not be glamorous, but they are an important and sometimes neglected step in mineral processing. Optimal attritioning will significantly improve the results and efficiencies of subsequent processing steps and can lead to reduced costs and improved product yields. Why is attrition scrubbing used? Attrition means to wear away a surface, typically by friction or abrasion. An attrition scrubber does exactly this, using impellers to force particles against each other, causing intense scrubbing, grinding, abrasion and polishing. This process is not a new concept. It has long been used in the glass industry to remove surface contaminants from silica. But it is also widely used in many areas of mineral processing and other applications including soil remediation and plastics recycling. In mineral separation, for example, the scrubbers help improve yield and efficiencies by preparing feed materials for downstream processes such as flotation, magnetic or electrostatic separation. Inefficient scrubbing can lead to coatings remaining on valuable minerals and decreased yields, as the covered minerals cannot be processed efficiently or are mistaken as waste contaminates and removed. In the example of flotation separation, pre-flotation conditioning uses attrition scrubbers to provide better recovery of minerals while using fewer chemicals. If surface contaminants remain on the mineral, yield is reduced, as the unwanted coating acts as a barrier to the reactants, which make it unfloatable and, therefore, unrecoverable.

Oct 1, 2013

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012

By Chee Theng

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 13th MPD Student Poster Contest on March 1, 2023, during the MINEXCHANGE 2023 SME Annual Conference & Expo. The event showcased the work of 24 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to showcase their research to a panel of judges during the conference. In recognition of their efforts, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest also includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 28, 2023

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation&apos;s Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman&apos;s communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By Arthur S. Maynard

There was a tendency several years ago for the average coal producer to more or less sit back satisfied with the big utility and metallurgical mar¬kets with long term contracts, not realizing, or possibly not evaluating correctly the importance of the growing industrial market Even the companies which were producing coal for the industrial market were primarily interested in the larger industrial customer, not fully realizing that a large percent of the industrial coal sold was to plants using less than 15,000 tons per year. As a result, possibly, the greatest inroad made by competitive fuel was made in this group. The situation mentioned previously cannot be blamed entirely on the fact that the coal markets were not evaluated in their proper perspective. Some of the responsibility would have to be due to the situation that existed during the last war&apos; and the period immediately following, when most of the coal was put to markets of higher realization, leaving the relatively small -industrial user-to get his fuel wherever he could. This usually would mean coal from some &apos;gopher hole" with fluxuating quality and supply. Therefore, it was not uncommon for some industrial customers to go to competitive fuels as soon as equipment and fuel were available. Fortunately, before this situation got completely out of control, the coal producers, realizing the seriousness of the problem, made available, usually through their sales department, combustion engineers and other specialists, to help the industrial user with his problems; The engineers usually found several problems, old equipment, use of incorrect size con¬sist, ash and fusion coals, lack of automation, fly ash and dust problems which increased cost and jeopardized the customer&apos;s relations with his employees and the public.

Jan 1, 1959

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry&apos; and the raw s, materials upon which it is dependent. Of the three type&apos;s of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996