Search Documents

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By Francois E. Heuze

We demonstrate a new capability to analyze the behavior of circular shafts in jointed rock. This was made possible by the development of a new, axisymmetric, joint finite element (2). Whereas the only previously reported such element was singular (1) and inadequate at some orientations, the current element has been extensively validated (3). The need for including discontinuities in a shaft analysis comes from two sources. First, the various rock formations may have discrete jointing, bed- ding, and interface between them. Second, there is a joint at the boundary between a concrete liner and the rock, and possibly between the various segments of the concrete liner. To demonstrate the applicability of the new model, we analyze a vertical circular shaft 5.4 m in diameter, in a series of horizontally bedded sandstones and siltstones. The shaft excavation is followed through three initial steps: 6 m, 15 m and 24 m deep.

Jan 1, 1979

By Robert G. Ditchburn

The Mariana arc is an ~1,400-km-long intraoceanic arc that marks the southern extension of the Izu-Bonin arc, and is host to 62 ?volcanic centers? of which at least 27 (21 submarine) are hydrothermally, or volcanically active. A surface ship cruise in early 2003 mapped the distribution of hydrothermal plumes emanating from these centers, followed by remotely operated vehicle (ROV) cruises with ROPOS in 2004 and Jason II in 2006. With the exception of one volcano (East Diamante), none of the vent sites visited by the ROVs were host to sulfide mineralization. Rather, they were characterized by high sulfidation mineral assemblages dominated by native sulfur. The sulfur was seen marking the vicinity of vent sites, or as sulfur ?chimneys? (e.g., NW Eifuku and Nikko), or more spectacularly as ?lakes? of molten sulfur, either occupying the summit crater of the volcano (e.g., Nikko), or perched on the flanks of the volcano, near the summit (e.g., Daikoku). Gas (H2S and CO2) was discharging through the molten sulfur. Evidence for these lakes to have either been substantially ?deeper? in their recent past (e.g., Nikko), or existing at other volcanoes (e.g., Seamount ?X?) is given by remnant ?pillars? of native sulfur that are reminiscent of rock pillars in lava lakes found along mid-ocean ridges.

Jan 1, 2008

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By Roger N. Kust

Because ammonia can form complex ions with certain of the transition metals, such as copper and nickel, it has long been of interest to extractive metallurgists interested in leaching or separating these metals. Although it is a relatively expensive reagent, ammonia is amenable to recycle because of its volatility. In development of processes utilizing ammoniacal leaching or separation schemes, information regarding solution vapor pressures, pH and solubility limitations is needed. There is voluminous literature on ammonia-water systems generated by the urea industry. However, frequently the systems of interest to metallurgists differ significantly in concentrations of ammonia used, the temperatures of interest. Furthermore, the differences arising from the presence of metal values in solution must be comprehended. There is surprisingly little information readily available regarding systems of practical interest to metallurgy. As a result, those interested in ammonia-based processes end up either doing expensive laboratory research to obtain necessary data or overdesigning the process. Another approach to obtaining desired information about ammoniacal systems is to attempt to calculate from first principles the various solution properties. This paper is being presented to illustrate what can be accomplished by estimating the state of equilibrium in an ammoniacal carbonate system from available thermodynamic information making simplifying assumptions when needed.

Jan 1, 1976

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By J. A. Herbst, Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous grinding mills through detailed mathematical models, a better understanding of the charge motion and rocklball segregation is needed. To achieve this a 0.61 m (2.0 ft) diam by 0.305m (1 .0ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video presentation (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rocksize distribution, and flow rates.

Jan 1, 1990

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By R. W. Reisinger

An historic underground copper mine in Wyoming is discharging neutral but copper-laden water into a pristine creek. The EPA-deferred site qualifies for reclamation by the Wyoming Abandoned Mine Land (AML) program; restoring the discharge so that the creek can eventually support a trout fishery is the cleanup goal. Hydrological and geochemical investigations underground have suggested two sources of mine water: one clean and the other copper-containing. Results of bench-scale and pilot-scale tests support the viability of using low-cost passive treatment techniques to reduce copper concentrations in the near-freezing mine discharge.

Jan 1, 1998

By Y. C. Guan

The leaching kinetics of chalcopyrite in ammonium iodide solutions with iodine has been studied using rotating disc. The variables studied J include the concentrations of lixiviants, rotation speed, pH of the solution, reaction temperature, and reaction product layer. The leaching rate was found to be independent with the disc rotating speed. The apparent activation energy was measured to be about 50 kJ/mole from 15°C to 35°C, and 30.3 kJ/mole from 35°C to 60°C. Experimental findings were described by a kinetic model, and the overall rate was found to be: (formula)

Jan 1, 1997

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By D. Wheeler

Similar to modern day petro-chemical processes, the flotation column is a complete break from the conventional manner of floating on a batch basis in cells. The column has a reputation of being only suited for cleaning applications, particularly that of molybdenum cleaning. The original column, invented and developed by Column Flotation Co. of Canada, Ltd., was developed as a Rougher-Scavenger. Only after proving its capability in this field was cleaning allowed. One rougher-scavenger column in closed circuit with a cleaner column produced better grade and recovery than a conventional cell plant consisting of one stage of roughing, two scavenging and four stages of cell cleaning. Three cleaner columns replaced 13 stages of conventional cell cleaning and resulted in higher grades and recoveries. The gentle countercurrent action of the column itself together with complete automatic control enable this machine to produce such results.

Jan 1, 1986

"From April 22 to 28, the eyes of the tunneling and underground construction world will be on San Francisco, CA, as the world’s most influential underground construction industry leaders gather at the Moscone Center for the 2016 World Tunnel Congress.Recognized as the most important international annual meeting for the industry, the 2016 version comes to the United States for the first time in 20 years and will be hosted by the Underground Construction Association of SME (UCA of SME). The conference will be held in lieu of the UCA’s biennial North American Tunneling Conference and will bring the strengths and resources of the UCA of SME and the International Tunnelling and Underground Space Association (ITA). The result will be a conference with unmatched technical programming and a showcase of more than 200 exhibiting companies.A program committee led by Randy Essex of Mott MacDonald, Lonnie Jacobs of Frontier Kemper Constructors, Michael Mooney, of the Colorado School of Mines, Priscilla Nelson, of the Colorado School of Mines and Amanda Elioff of Parsons Brinkerhoff formed the program committee and worked for more than two years to build the program. The result is four technical sessions with five tracks in each session and 185 oral presentations.“One challenge was the sheer size of the group that would be assembled, perhaps 2,500 attendees or more, and the large number of abstracts we were likely to receive,” said Essex. “ We investigated extending the conference a fourth day, but that was not workable with the Moscone Center. We settled on having five concurrent technical tracks – something that has not been attempted in past NAT or RETC conferences to my knowledge. The next step was to develop suggested session titles that would span the breadth of subjects that would interest conference attendees as well as serve the conference theme.”"

Apr 1, 2016

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010