Search Documents

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By Warren D. Stanford Stanford

Introduction The Sleeper mine is a near-surface gold mine located in a remote area 56 km (35 air miles) northwest of Winnemucca, NV (Fig. 1). The deposit was discovered in 1984 by an Amax exploration geologist. Favorable drilling results led to feasibility studies and metallurgical testwork. Final evaluation of the mine potential proceeded very quickly. The project received Amax board approval in July 1985. Eight months later, the process plant was fully operational. The first gold ($1 million) was shipped one month later, in March 1986. Total plant capital was $27 million. Payback was achieved in six months. The Sleeper mine was expected to produce 1.6 t (53,000 oz) of gold and 1.3 t (41,000 oz) of silver annually. However, the ore body exceeded all expectations. Production for the first 10 months of operation amounted to 4 t (128,000 oz) of gold and 2.9 t (94,000 oz) of silver. Direct cash operating costs are in the $1.77/g ($55 per oz) range. Amax is actively conducting exploration nearby for additional reserves to extend the mine's life. (See update on page 242.) Geology The Sleeper gold deposit is located on the northwestern flank of the Slumbering Hills and in the Awakening Mining District. Rocks exposed in the vicinity of the deposit are interbedded siltstones, sandstones, and limestones of Triassic age. They are overlain by latite lava flows and tuffs of Tertiary age. Dikes and sills of latite and andesite intrude the sedimentary rocks. Quaternary deposits of mostly sand with minor gravel and clay cover a pediment containing the gold deposit. The sedimentary and volcanic rock units have been transsected and offset by extensive north- northeast trending faults and less abundant northwest trending faults. Both fault systems fractured and prepared the ground for subsequent invasions of mineral-bearing hot spring geothermal waters. The hot spring systems produced widespread hydrothermal alteration and gold mineralization at silicified centers near feeder fault structures. The deposit is hosted by siltstone and latite that have been hydrothermally brecciated. The main breccia is elongated north-northeasterly. The hydrothermal breccia zones appear to dip steeply to the west. Gold mineralization consists of native gold and electrum deposited in two or more high-grade quartz-breccia veins. Lower grade gold mineralization occurs

Jan 4, 1987

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By John Batchelder

The Copper Canyon Cu-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.-old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Calculated 6dD values of water in equilibrium with primary and secondary biotites range from -76 to -99 per mil at temperatures indicated by d180 values from coexisting quartz and biotite. The lightest values are in secondary biotite from the east ore body. These data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1976

By B. W. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the design and ultimate economic success of the project. An incorrectly-determined lifetime can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the calculation of the optimal lifetime using both traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the net present value of the project is maximized.

Jan 1, 1992

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

By Dhananjay Kumar

In past, no serious attempts have been made to study the effects of operating environments on performance characteristics of a mining system. In this paper, proportional hazards model (PHM) analysis technique is introduced which can be used to analyze the effects of operating environments on the performance of a mining system. It can be used to select suitable materials, manufacturers or designs of items for a particular working environment. In this paper some applications of the PHM are discussed with examples from a Swedish mine. Its application for decision making in maintenance is also discussed.

Jan 1, 1992

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By P. Verhoeven, G. Hefter, P. M. May

The dissociation (ionisation) constant of hydrogen cyanide, pKa(HCN), has been measured by high precision glass electrode potentiometric titrations in saline solutions containing up to 5 mol/L sodium chloride. The dissociation constant of water that is necessary for the calculation of pKa(HCN) has also been measured. In saline solution, and in contrast to literature values, pKa(HCN) changes considerably at both high and low ionic strengths as a result of changes in activity coefficients. In addition an equation is presented, using literature data, that describes the variation of pKa(HCN) with temperature up to 150°C. The significance of the changes in pKa(HCN) for optimising the pH of alkaline cyanide gold recovery streams is briefly discussed.

Jan 1, 1991

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By Calvert D. Iles

Open-pit mines in the US and throughout the world are typically characterized by increasing operating costs and decreasing ore grades. Thus, companies must continue to improve their use of human and technological resources to remain competitive in the marketplace. Duval Corp. has historically been very sensitive to mining costs, in part because of relatively low grade copper-molybdenum ore bodies. These concerns have resulted in three haulage system generations at the 218 kt/d (240,000 stpd) Sierrita-Esperanza open-pit mine south of Tucson, AZ. Each generation has exceeded the performance of the one replaced. The latest system of portable crushers and conveyors reduces hauling costs by combining both hardware and technique. Savings are achieved not only bysubstituting conveyors for haul trucks, but also by permitting the crusher-convey or system to closely follow mining as the pit deepens and/or mining areas change location. The Duval system is capable of easy and inexpensive relocation in varying site configurations in relatively short time periods. Its implementation in active mining areas results in minimum disruption to both the mine operation and mine design. This haulage concept allows the mining engineer maximum freedom to design an open pit for profit rather than for equipment. Maximum savings with a portable system are achieved by minimizing truck haulage costs. At Sierrita, for example, the yearly estimated operating cost savings for each thousand feet of +10% truck ramp replaced by conveyors is about $1 million per portable crusher. A savings of $30 million could be achieved fora three-portable system overa 10 year period simply by reducing the average truck Iiftto the crusher by 30 m (100 ft), There is also the added capital expense of buying trucks to cover the additional 30 m (100 ft) of lift. Relocation costs are an important consideration in a portable system. Direct costs can become a significant operating expense if frequent relocations are necessary to take full advantage of potential haulage cost savings. A site preparation cost of $375,000, for example, would add an additional operating cost of 2.8¢/t(2.5¢/st) for a system handling 13.6 Mt/a (15 million stpy), assuming one move a year, In addition to the direct cost of site preparation, such as installation of retaining walls, apron feeder slots, and equipment pads, there is the cost of site renovation after abandonment. Indirect relocation costs, while less tangible and more dependent on specific mine design and scheduling, can be of significance. A slowdown in the mining rate or a less efficient mining plan can result from a site not being immediately available for mining after abandonment. Conversely, mining in narrow areas can be adversely affected if two or three month lead times are required for site preparation.

Jan 4, 1983

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By Robert L. Sundeen, Richard V. Wenberg

Service vehicles, often called support vehicles or auxiliary vehicles, are used in secondary functions to support production activities such as loading, drilling, and timbering. Probably the most common support vehicles are the personnel carriers used to move miners to and from work areas. Utility designs are used to transport supplies and various less mobile equipment. Specific application designs are used for special work such as explosives transportation and loading, equipment maintenance, and equipment lubrication. PERSONNEL CARRIERS Personnel carriers are available in a wide variety of sizes and configurations. Some are two-wheel drive, though most are four-wheel drive. Smaller versions carry at least two men and usually have sufficient capacity to carry a small payload of supplies or equip¬ment. The American Motor's 05 Jeep, equipped with an optional diesel engine, has been adapted successfully for this light duty. Larger personnel carriers with ca¬pacities of 12 to 20 or more men currently are available, as shown in Fig. 1. The designs often are customized to the operating characteristics of each mine. All meet the latest federal requirements for rollover protection, emergency brake systems, etc. UTILITY VEHICLES Utility vehicles are adaptable to numerous duties. Probably the most common are ordinary haulers with a flat bed or low-sided box. They are used for hauling supplies and equipment from one point to another. Some occasionally are used for towing and may pull one or more trailers. Fig. 2 shows a typical utility truck. SPECIAL-APPLICATION VEHICLES Special-application vehicles are possibly the most important of all support types since these vehicles di¬rectly support and maintain production equipment. Such vehicles are available in a wide variety of sizes, mechanical functions, and operating specifications. Most versions are four-wheel drive and articulated. Among the more common vehicles are explosive haulers and loaders, mechanic's trucks, lubrication trucks (Fig. 3), and special carriers. TYPICAL APPLICATIONS Development Utility haulers are essential in trackless operations to bring supplies to advancing headings. Some utility haulers may be dedicated to bringing in steel sets and may be equipped with boom lifts to unload heavy sup¬ports or even place them as required. A rockbolt hauler may have a boom-mounted operator's basket which can be used for bolt installation or inspection. Various mechanic's trucks and pipe trucks service the heading to keep power, air, water, and ventilation at the face and to keep face equipment at maximum utilization. Production Production operations require a variety of support equipment. Because of the larger crew size brought about by the addition of the production force, personnel carriers play a greater role. Correspondingly, steel¬support hauling equipment and bolting trucks usually see limited application. PRODUCTION UNITS Capacity Personnel carriers are available to carry almost any number of people desired. Likewise, other types of carriers or haulers can and are built to fit specific re¬quirements. Physical size, capacity, and operating char¬acteristics can be varied to fit any size of opening and operating condition. Generally, articulated models offer greater maneuverability than straight frame-axle steer designs. Most vehicles of this type are lower in power than production units, generally under 74.6 kW (100 hp). Operating performance still compares favorably to that of production equipment, i.e., the support vehicles can travel at equivalent speeds on the various mine gradients. Manpower Auxiliary vehicles should require only a single opera¬tor. Specific application vehicles may require more than one person. For example, ventilation trucks usually require a crew of two where pipe must be installed.

Jan 1, 1982

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of both underground and surface operations. The East Ertsberg Skarn System (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production is from the third lift (Deep Ore Zone), which is scheduled to peak at 80,000 mtpd during 2009, with this rate sustained through 2015. The orebody is proven below the existing caving level, with the next vertical block called the Deep Mill Level Zone (DMLZ). This paper presents an overview of the DMLZ Mine based on recent feasibility level study. The mine is being designed for a peak production rate of 29.2 million mtpy, with 1,803 total ore draw points spread over a panel caving footprint of about 1.3km by 375m. The present reserves for this mine total 501 million tonnes. Located 1,400-1,800m below the original surface, the DMLZ will be one of the deepest caving operations in the world. Production is scheduled to commence in 2015. Discussion is provided on most design aspects including; caving methodology and layouts, geotechnical predictions and risks, ore handling systems, ventilation design and associated infrastructure, high-lift pumping system, cost estimation and expenditure scheduling.

Jan 1, 2010

By D. E. Ranta, Stephen W. Thomas, Clancy J. Wendt

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A. A relatively large sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B. When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves. C. Values are usually erratically distributed within the gravel mass. Therefore, some placers with a more uniform value distribution may be adequately assessed with a minimum number of samples whereas a deposit with a highly erratic distribution of values may not be adequately sampled regardless of how many samples are taken. D. The investigation of a placer deposit should be made by, or be under the direction of, a person experienced in the art of placer sampling. F) During a sampling program, items that must be observed and noted in addition to the sample size and valuable mineral content should include boulder size and number, clay content, bedrock conditions, water, frozen ground, false bedrock, and any other physical characteristics that would affect mining of the deposit.

Jan 1, 1992