Search Documents

By Howard E. Banta

From Alaska to Florida and California to Maine, the National Forest System (NFS) is host to unprecedented levels of prospecting and development. The NFS is large (191 million acres), geologically attractive from the mineral standpoint and relatively unexplored. Significant recent finds and developments involve silver, gold, platinum group metals, molybdenum, cobalt and phosphates. Exploration and development are closely regulated, but most of the NFS is open. The Forest Service endeavors to be a good host to the mineral industry, but increasingly is asked or forced to delay or disapprove mineral projects to protect the environment.

Jan 1, 1984

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By Roberto Pimentel de Souza

Since 1976 CVRD is carrying out tests to develop a type of pellet made with organic binder. One binder that showed good possibility to be used in industrial plants is Peridur. An extensive framework of tests was run in CVRD&apos;s pilot plant. The results are presented in this paper. Finally, the decision was taken to carry out an industrial production of 50.000 t of pellets. It was scheduled for March &apos;81. The results are shown in this pager. It was not observed any detrimental effect of the peridur neither in the process nor in the product quality.

Jan 1, 1981

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By E. R. Palowitch

On February 5, 1973, Eastern Associated Coal Corp began shortwall mining in their Federal No. 1 Mine, thus marking the first attempt in the United States at modern shortwall mining, i.e., using a continuous miner to extract coal open-ended from pillars 100 to 200 feet wide, under the protection of a self¬-advancing roof support system (1)1/. Since then, four additional shortwall faces have been operated. While the number of face-years of shortwall experience in the United States is limited, this experience has been anything but uniform. Differences in operator motivation, coalbed parameters, geologic conditions, panel dimensions, and face equipment all have contributed to a wealth of knowledge which can provide guidance for the design of future shortwalls. The purpose of this paper is to review the history of shortwall mining in the United States and to assess its value to the U.S. coal industry in terms of the health and safety of the miner, the percentage of coal recovered, coal production, worker productivity, and relative cost performance.

Jan 1, 1976

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant&apos;s -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994