Search Documents

By J. M. Van Langen

In 1965 Hoogovens was looking for additional capacity for burden preparation in the order of 2,5 to 3 million metric tons per annum of some kind of optimal blast furnace ore feed. In principle four solutions offered them-selves for further investigation: 1. purchase of screened ore and/or run of mine ores with the provision of a corresponding ore screening capacity on the blast furnace site; 2. manufacture of sinter; 3. purchase of pellets; 4. manufacture of pellets. After studying the technological, technical, economical and commercial factors Hoogovens decided for the last mentioned possibility. Before taking this decision not only a great number of different mixtures of iron ore were tested, but during a long period in one of the big blast furnaces a number of tests were also executed with purchased pellets from South and North America. It was found, that using 50% acid pellets with 40% basic sinter a coke rate saving of 25 kg per ton hot metal (50 lbs/net THM) and a production gain of 15% could be obtained as compared with a full sinter practice. With some pellets it became clear, that due to properties, commonly referred to as swelling, we got very poor furnace performances; so in studying the production of pellets, pellet quality should be regarded as the most important aspect of the problem.

Jan 1, 1972

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By Karin Bäppler

Hydropower produces almost two-thirds of the world’s renewable electricity generation and delivers a major contribution on the ambition of the Paris Agreement and Sustainable Development Goals (SDG) with a range of benefits to society and environment. These include clean and flexible generation and storage in addition to reduced dependence on fossil fuels and avoidance of pollutants. The Limberg III PSP is one of the European projects that addresses the implementation of the UN SDGs. The challenge of the project is the construction of a 770 m long pressure shaft to be excavated with a TBM at an inclination of 42°.

Jun 13, 2023

By H. Sevim

Belt network simulators developed in the last two decades are reviewed. Critical parameters in belt network design are identified, and the capabilities of belt simulators in providing values of these parameters are investigated. An alternative design model that optimizes values of the critical parameters is introduced. To illustrate the capabilities of the alternative model, a real life case is treated and the outcomes are discussed.

Jan 1, 1990

By M. G. Rylatt

The Ekati process plant flowsheet features the common steps in diamond recovery plant design. Primary treatment and concentration is by crushing, scrubbing, high-pressure grinding rolls and heavy medium separation (Fig. 1). Secondary concentration is by an attrition mill; wet, high-intensity magnetic separation and X-ray sorting (Fig. 2). All of these are performed on site, although final sorting of the diamonds into commercial categories will be carried out elsewhere. The initial throughput rate is 9 kt/d (9,900 stpd), increasing to 18 kt/d (20,000 stpd) during the first 10 years of operation. A range of ore characteristics will be encountered that will effect the plant operating conditions during the life of the mine. The adopted design envelope is based on these expected variations. The design is based on the use of large-scale equipment, incorporating the latest and most efficient technology available. Where proven technology exists, no attempt was made to reinvent the wheel. However, where recently developed technology offers a significant advantage, this has been incorporated into the design. The Ekati run-of-mine (ROM) and coarse ore handling facilities are unheated, to take advantage of the better handling characteristics of the frozen ore in winter. The stockpile reclaim features an MMD mineral sizer (a toothed roll crusher) to minimize the problems of handling thawed, sticky kimberlite in the summer and break frozen lumps in the winter. All processing downstream from primary crushing and the coarse ore stockpile is carried out in a temperature-controlled environment in the main process plant building. Personnel involvement in the process is mini¬mized by using a Modicon Quantum series PLC with human-machine-interfaces (HMI) running Wonder-ware software on dedicated personal computers.

Jan 1, 1999

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Luis Pommier

The requirements of metals by modern society have created big challenges for mining engineers minerals processing engineers, metallurgical engineers and economists to produce these metals economically from mineral deposits which contain, with time, less and less value. The advances of science and technology allow, today, the exploitation of mineral deposits which only few years ago would not have been considered economical. However, there are limitations both on the minimum grade of recoverable values contained in the ore to be fed to a mill or on the concentrate to be smelted, and on the maximum content of "impurities" i.e. chemical elements which are difficult or expensive to refine from the ore, from the concentrate or from the metal. It is also known that the cost of treatment in a mill or in a smelter, for unit of metal contained in the ore or in the concentrate, increases as the grade of the recoverable values contained in them decreases and also if the content of impurities increases. In order to work a mineral deposit economically it is necessary to ensure not only that it has more than a minimum content of values, less than a maximum content of impurities and that there exists a good up-grading or metallurgical process but also to ensure that the opti-

Jan 1, 1971

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By P. T. Luckie

Analysis of classifier performance independently of a closed grinding circuit configuration may result in a poor match-up between the grinding device and the classifying device. This paper examines the relationship between classifier and grinding device in dry grinding circuits by employing a semi-empirical methodology.

Jan 1, 1980

By A. Durnan

Barrick Goldstrike Mines Inc. (Goldstrike) operates a six circuit (train) pressure oxidation plant for the pretreatment of gold bearing sulfide ores. The property is located 27 miles north of Carlin, Nevada. Since the commissioning and start-up of the first circuit in 1990 until the present total plant availabilities have exceeded 90%. The discussion that follows will detail the maintenance practices employed to consistently achieve this goal.

Jan 1, 1994

By Herschel H. Potter

While preparing this paper, I soon realized I had a problem in defining what injuries should be classified as "personal." Admittedly, in some cases, falls of persons, sprains and strains, pulling and pushing injuries, and back injuries may have been caused by the individual. But, I believe the number of injuries directly attributed to an individual's carelessness is relatively small in comparison to the total number of injuries in those categories. For discussion purposes, the injuries most often considered to be personal, that is, caused by individuals are those classified as back injuries. My paper will be devoted to back injuries because this category represents the greatest number of injuries occurring in coal mining. A man's best friends are his wife, his back, and his dog. The back, however, has a reputation of not being as faithful as his other two friends.1 "Industrial back injury is one of the major occupational health problems plaguing industry to- day. According to national surveys, back injury accounts for more lost time than any other occupational injury and costs companies thousands of dollars in compensation, medical fees and over- time pay."2 A study conducted by USA Today found that back ailments afflict an estimated 75 million Americans, have totally disabled about 2.5 million adults, lead to as many as 200,000 required surgeries each year, are a leading cause of absenteeism and disability, are the second leading cause of hospitalization, are responsible for 18 million doctor visits a year and cost about 93 million work-days annually. The cost to industry is estimated at $14 billion a year.3 During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, this effort has not produced any great change in the incidence of the injury. Back injuries should be of the utmost concern to everyone here today. I don't need to tell you what the incidence rate is for back injuries, nor will I use any statistics to inform you of the incidence rate for the coal mine industry or any specific mine. It is only important to know that the number of back injuries is excessive. Back in- juries resulting from lifting have been and continue to be one of the most constant and undiminishing problems in the occupational environment. The fact is, we use our backs to per- form work that the back was not designed to do. Historically, manual materials handling related accidents have consistently accounted for the largest percentage of all industrial accidents. In fact, over 25 percent of all industrial accidents are related to handling of materials.4 In underground coal mining operations, material handling accidents account for even larger percentage of lost time injuries. In 1983, for example, they accounted for 34 percent of all lost time injuries and 32.6 percent of all non-lost time injuries. 5 I want to use one example of a task that will illustrate what I have just said: the building of a concrete block stopping. Each solid concrete block will weigh from 60 to 70 pounds. To build a stop- ping 6 feet high and 20 feet wide will take approximately 80 blocks. On the average, these 80 blocks will be handled at least four times from loading into the conveyance for transportation to being placed while constructing the stopping. This generally requires repetitive lifting from ground level. The next three slides demonstrate the lifts

Jan 1, 1986

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015