Search Documents

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By K. Nagata, T. Kawashima, S. Tejima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service, port construction, trans-shipment, and environmental control. The major problem is the shipment of coal. Customary methods for bulk transfer must be improved and new systems developed. Slurry unloading has a key role in the new systems. This report reviews progress in slurry transportation research that has been done in Japan since the 1960s, when large-scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are focused on.

Jan 1, 1987

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2017

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2018

By X. Song, Q. Zhang

"The development of fracture zones in surrounding rock mass has significant impact on the stability of underground mine roadways. Detection of the fracture zones is of compelling importance for maintaining roadway stability as well as for safe and speedy excavation of the roadways. This paper presents a study conducted at Dong Bao Wei underground coal mine, where the roadways were developed in diabase rock mass. The roadways suffered severe damages, including sloughing and excessive floor heaving. The borehole imaging technique was applied in the study to observe and detect fracture zone development surrounding the roadway openings. Based on the borehole imaging studies, new roadway support systems were proposed to improve the stability. INTRODUCTION At the Dong Bao Wei Coal Mine three main roadways of the west wing were excavated. The three roadways had semicircle arch cross sections and were at a depth of 650 meters, each being about 750 meters in length. The roadways were driven through a section of thick diabase intrusion, which was softened by water with reduced strength and may turn into powder form under weathering. Site investigation indicated that the roadways in diabase intrusion zone were badly damaged due to severe deformation, and very serious roadway sidewall sloughing and spalling accompanied by severe floor heave often occurred.(Figures 1 and 2) In order to ensure the normal use of the roadway, undercuts were excavated. However, this operation seriously affected the roadway construction progress and increased the amount of roadway support operations as well as the roadway maintenance costs. Furthermore, a roof fall accident occurred in nearby drilling site. The investigation indicated insufficient support provided for the roadways which imposed significant safety hazards and would have serious impact to mining production and subsequent mining activities.The support of the main roadways is a critical task and is the focus of the underground opening excavation work at the mine, since more than 40 years of service life is required from these main roadways. For these roadways, large cross sections with high degree of stability and minimal amount of deformation should be maintained. Therefore, providing sufficient and appropriate roadway supports is of significant importance to the coal mine. In this paper, in order to optimize the roadway supporting system, studies were carried out on the geological structures, lithological characters, roof bolt anchoring features and suitable anchoring layers. The studies were aimed at ensuring the stability of mine roadways, reducing the roadway maintenance costs and providing a safe mine passageway for orderly production and progressive development of the mine"

Jan 1, 2016

By K. N. Han, H. C. Cho, R. Kim

"As an extension of the work on the effect of OH- on various cations in hydrometallurgical systems, the effect of Cl-, Br-, I- and CN- on cations such as Ag+, Cd2+, Hg2+, Cu+, Cu2+, Co2+, Zn2+, Pb2+ and Sn2+ has been examined in detail. The Newton-Raphson technique has been used to determine the amounts of various metal species as a function of the concentration of anions. Some practical implications of various metal complexes in metal separation and removal from solutions have been examined and discussed.IntroductionUnderstanding the role of anions in hydrometallurgical processes often determines the success of an operation. The successful choice of concentration and type of anions not only leads to an effective extraction and removal of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2009; Al-Tarazi et al., 2004), but also to assisting effective separation of various metals, whether it is a solvent extraction, ion exchange operation or even a simple precipitation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974).This paper continues the discussion of the role of anions in hydrometallurgical systems beyond the role of OH-, which was the topic of a previous paper (Kim et al., 2014). Table 1 lists various anions that are frequently used in conjunction with metal ions to be selectively separated or precipitated. As seen in the table, many anions are used frequently in hydrometallurgical practices. Some of the more frequently used anions include OH-, SO4 2- and CO3 2-. The halogen elements, Cl-, Br- and I- , as well as CN-, are also used in hydrometallurgical applications, especially in relation to noble metal recoveries (Meng and Han, 1994; Zhang et al., 1996; Sun et al., 1996; Starovoytov et al., 2007)."

Jan 1, 2015

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988

By Paul Piercy

Bougainville Copper Limited operates a porphyry copper mine in Papua New Guinea. The waste dumps will contain 400 to 500 million tomes of rock at the end of nine life. The paper describes investigations carried out over a period of en years and highlights the problems associated with waste lump leaching in a tropical and seismic active region. Aspects discussed include mineralogy, chemical reaction, leaching rates, microbiological activity, dump stability, dump structures, effects of tropical conditions, seismic activity and topography.

Jan 1, 1981

Geostatistics is well known as a tool for ore reserves calculations at the exploration stage. The goal of this paper is to show geoscatistics can also contribute to productivity gains, allow better selection of the mining methods and better control of the grades during production. The first two examples show how geostatistics can provide sophisticated models, using conditional simulations and the use of them for simulations or optimizations of mining processes. A third example will show how to use geostatistics for short term planning in a large polymetallic vein type mine.

Jan 1, 1983

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By Horst Huettenhain

The Rowland Coal Preparation Plant is located on Workman's Creek in Raleigh County, West Virginia, approximately 20 miles Northwest of Beckley and 10 miles Southeast of Ameagle. It is owned and operated by the Rowland Division of Consolidation Coal Company. This paper describes the plant flowsheet, process considerations that were evaluated in its development, and observations made during and since the plant was constructed. The final flowsheet was developed specifically to wash the coal from the Rowland Mine and contains several equipment combinations and applications heretofore never placed in a single, commercial operation. The major process equipment is presented in a functional description of the flowsheet. The coal reserves are leased from the Rowland Land Company and consist primarily of #2 Gas and Middle Eagle coals and various major splits of the Middle Eagle seam. The Rowland Coal Preparation Plant was designed to process 560 TPH of raw coal consisting of 50 percent #2 Gas coal intimately mixed with 50 percent Middle Eagle coal and containing lumps no larger than a 12-inch cube.

Jan 1, 1970

By Walid M. Abdellah, Soliman Abu Elatta A. Mahmoud, Hanaa A. Abu Khoziem

The high-grade Th-U-Y zone is one of the numerous mineralized zones found in the El Garra El Hamra hydrothermally altered syenites in southwestern Egypt. It is characterized by the thorium minerals thorite and thorogummite, which are closely associated with xenotime-(Y). This zone of mineralization is localized in the eastern part of the El Garra El Hamra hydrothermally altered syenites. This zone does not relate to the first phase of syenites that appeared on the surface but is linked to the other, hidden phase of the syenitic body. Additionally, the fluids responsible for the mineralization of this zone belong to the late-stage hydrothermal event as well as the fault action due to the fact that it had continued reactivations for a long period of time. The studied mineralized zone also contains ceriopyrochlore-(Ce),(Ce,Ca,)2 (Nb,Ta)2O6 (OH), fluorite (CaF2) and barite (BaSO4), which are found in considerable amounts, whereas apatite (Ca5(PO4)3F) and chromite (FeCr2O4) are rarely found together with Fe-oxi-hydroxides (hematite and goethite) with a minor amount of jarosite (KFe33+(OH)6(SO4)2). Finally, the main constituent mineral in the zone is the pseudomorph perthite in addition to quartz, which is found as deformed crystals. A technological sample was collected from this zone and was found to assay 4.62 weight percent thorium (Th), 0.37 weight percent uranium (U) and 3.12 weight percent rare earth elements (REEs). From the chemical and mineralogical composition of the studied technological sample, the leachabilities of Th, U and REEs were investigated using sulfuric acid (H2SO4) agitation leaching and pug leaching methods. The latter was found to be preferred under the conditions of 0.54 ton H2SO4 per ton of altered syenite at 110 °C for two hours.

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By E. F. Nelson

The 1970s have witnessed the completion and successful start-up of several new non-ferrous metallurgical operations in the Western Hemisphere which utilize large semi-autogenous mills in the grinding circuits. These facilities' are arranged either as single-stage circuits, or in a two-stage configuration n with ball mills. Another major concentrator, designed with an autogenous mill, ball mill, crusher (ABC circuit), is presently under construction and scheduled for start-up late this year. The large primary mills employed in these circuits have high diameter-to-length ratios and are designed to accept a very coarse feed, i.e., the product of a primary gyratory crusher, or run-of-mine ore. This characteristic obviates the need for a secondary-tertiary crushing plant or, in selected cases, even a primary crusher, which is a basic requirement in feed preparation for conventional grinding mills. This paper discusses three such grinding circuits and, presents operating data for two of them: the Island Copper Mine of Utah Mines, Ltd., near Port Hardy, British-Columbia,- and the Pueblo Viejo Cyanide Leach Plant of Rosario' Dominicana, S.A. on the island of Hispaniola. The design criteria for the Cyprus Bagdad Concentrator under construction' at Bagdad, Arizona, are also included. Data pertinent to these circuits are tabulated in the Summary.

Jan 1, 1977

By Olivier Kraft, Olaf Kortz

"Project-specific optimized tunnel boring machines represent the spearhead of technological progress in tunneling because with their use, very long-lasting, high quality tunnel structures in almost any geology, depth and topography can be produced with a high degree of automation. The mechanized excavation of tunnel structures ensures the greatest possible environmental protection during tunneling itself. Professional, systematic and high quality rebuilds and reuse of already proven equipment also ensures maximum efficiency in the use of materials and energy resources. It offers an enormous potential for a highly optimized environmental balance. Here the manufacturers of tunnel boring machines and their users in particular have a duty to ensure transparent, high quality and binding standards in the entire rebuild cycle and in the refurbishment management of innovative tunneling technology. This paper deals with the comprehensive processes with rebuild levels of tunnel boring machines and highlights some exemplarily implemented projects. 1 INTRODUCTION All over the world, the number of tunnel boring machines (TBM) in which equipment rebuilds from previous projects are re-used has increased over the last few years. This text presents the technical and economical aspects of this market development. It also takes a look at the practical implementation of rebuild measures. The ""ITAtech Guidelines on Rebuilds of Machinery for Mechanized Tunnel Excavation"" from 2015 lay down the requirements that the machine manufacturers must meet. 2 ECONOMICAL AND ECOLOGICAL ASPECTS OF RE-USING COMPONENTS The globalization of the construction sector and the consideration of environmental aspects promote an increased re-use of machines and machine components. Nowadays, large-scale construction projects are often carried out by international joint ventures of several individual companies that are established specifically for this purpose. After the completion of the project, the joint ventures are dissolved and they liquidate their project-specific equipment, such as tunnel boring machines. Today, it is much more uncommon for such machines to remain permanently in the possession of construction companies. Joint ventures offer TBMs on the free market, or they exercise contractually agreed repurchase options with the manufacturer. On the whole, this increases the number of re-usable components or complete tunneling systems available on the market."

Jan 1, 2016

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines paper to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios are prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992