Search Documents

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Daryl R. Tweeton

Bureau of Mines research in in situ uranium leaching includes injection well construction and environmental aspects. Clogging of injection wells is a common problem, and is affected by construction techniques. Part of the clogging can be caused by a low-permeability skin left on the borehole wall if the drilling fluids are not thoroughly flushed out. Certain polymer drilling fluids are less prone to cause clogging than bentonite muds, since a lower solids content can be used. The environmental research primarily involves two contracts. The first describes the environmental impact of in situ leaching and the effect of environmental legislation on leaching; the second describes the cost effectiveness of various methods of restoring ground water quality.

Jan 1, 1978

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985

By R. Jedrzejczak

Endako Mine is an open pit molybdenum mine located in the north central region of British Columbia, Canada, approximately 160 km. west of Prince George. Production for the latter part of 1992 is expected to average at 63,500 tonnes per day of which 27,000 tpd constitute the mill feed. This production is achieved with five 15 to 19 cu. yd. electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 121;.1 inch electric rotary drills. There are three ore zones delineated into pit areas called the Endako, Denak East and Denak West. Present mill feed source is the South East stage of the Endako Pit while the stripping is carried out in the South Wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM/BM/flotation circuits. The majority of the Molybdenum Sulphide (MoS2) is roasted on site to produce technical grade Molybdenum Oxide (MoO3) while a portion is further refined and treated to yield a 99.9% pure Molybdenum Sulphide (MoS2) "Ultrapure" product.

Jan 1, 1993

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Shiou-Chuan Sun

The froth flotation of coal, differing greatly from that of most minerals1-5, is not improved but rather impaired by temperatures higher than room temperature6-10 This phenomenon has long taunted us for an explanation. Gayle and Associates 8,9 reported the lack of relationship between their contact angle measurements and their flotation of American coals under various temperatures. Bailey and Whelan6 stated that the viscosity of flotation reagents, offering some clue for their flotation of British coals at low temperatures, could not be put forward as an explanation either in whole or in part for the effect of temperatures on coal-flotation. In this paper, a froth hypothesis is proposed to explain the flotation behavior of coals under various pulp temperatures. Test work involved the flotation of coals and the frothing of reagents.

Jan 1, 1966

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

With the depletion of mineral resources and the growing demand for metal resources from industrial development, the recovery of metal resources from secondary resources has attracted increased attention. Among all secondary resources, spent catalyst is one of the most important as it contains valuable metals such as vanadium, nickel, molybdenum, cobalt, and aluminum. Compared with the extraction of metals from minerals, the recovery of valuable metals from spent catalysts has the advantages of a simple process, a short production cycle, lower investment cost, and less environmental impact.

Apr 1, 2023

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By P. M. Hawley

In April 1975 Kaiser Steel Corporation and the United States' Department of Energy entered into a cost-sharing agreement for the demonstration of shield-type longwall supports on three consecutive longwall panels at Kaiser's York Canyon' Mine in New Mexico. Under this agreement the Department of Energy supplied 117 Hemscheidt 320 HSL caliper-type shield supports and hydraulic pumps for the duration of the demonstration. The purpose of the demonstration was to educate the U.S. coal mining industry as to the benefits in production, productivity, health and safety, and increased coal extraction afforded by shield-type longwall mining systems and to provide the industry with a working model. A detailed description of this demonstration is given in U.S. Department of Energy Publication No. DOE/ET/12530-T1, entitled "Demonstration of Shield-Type Longwall Supports at York Canyon Mine of Kaiser Steel Corporation," hereafter referred to as the York Canyon Report.

Jan 1, 1984

By W. G. Lawrence

The rapid development of science and technology in Russia has been the result of well laid plans since 1918. At that time the Institute of Silicates was established is Moscow and later the establishment of similar more specialized institutes for the study of cement, glass, refractories, construction ceramics, electrical ceramics, building materials and asbestos provided the necessary research facilities for studies related to all types of ceramic inorganic materials. The' Institute of Ceramics and the Institute of Silicate Chemistry, Academy of Sciences, USSR, were founded in Leningrad. The work now going on in these various research' institutes covers every branch of silicate science and ceramics The impetus behind such establishment of special¬ized laboratories is no doubt due to the 5-year plans and the necessity of improving the scientific knowledge regarding the materials being used and the products being manufactured.

Jan 1, 1960

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By John Berney-Ficklin

Large scale grinding mills can reduce both capital and operating costs for concentrators. These mills can be effectively used, but they must be free from design and manufacturing deficiencies if they are to reach their full potential and avoid costly downtime. This paper presents the evolution of today's complex grinding mill specifications and discusses the most important items to look for when buying new equipment. It emphasizes the need to monitor specification requirements during design and manufacture. It also discusses the growing trend to have grinding mills fabricated in overseas plants, and the importance of recognizing this when preparing specifications.

Jan 1, 1987

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019