Search Documents

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By Roger J. Araujo

A photochromic material is one which undergoes a change of color when exposed to light and reverts to its original color when the light is removed. Review articles carrying extensive bibliographies have been written by Brown and Shaw (1) and by Schwab and Bertelson (2). Organics. Schwab and Bertelson divide the reactions in different organic photochromic materials into some half-dozen categories; Windsor (3) reduces these to the following three main classes of general interest, based on how they work. 1. Stereoisomers. Absorption of light breaks one of the chemical bonds in a. ring molecule, thus allowing the molecule to unwind and form a different geometrical arrangement. The reverse process is a reforming of the bond. Examples of this class are the spiropyrans and the anils. 2. Dyes. A triphenyl methane dye, for example, is oxidized by energetic light; the absorption characteristics of the positive ion so formed are different from those of the original electrically neutral benzene rings. 3. Triplet States. In the class of polynuclear aromatic hydrocarbons, ground-state molecules are excited first to a singlet state by irradiation, and then go, via the lowest triplet state, to an excited triplet state. Visible light is absorbed in the triplet-triplet transition.

Jan 1, 1970

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non-bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30% and 50% alunite between 50% and 70% quartz with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone and a chlorite-montmorillonite zone. Total U.S. reserves of alunite were estimated at 20 million metric tons (at 30% alunite) by the U.S. Bureau of Mines in 1941. Here recent work by the U.S. Geological Survey estimates reserves of 252 million metric tons and potential resources at 1.4 billion metric tons. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves at these properties are estimated to be about 650 million metric tons. Inferred reserves are estimated at 2.5 billion metric tons and potential resources at 8 billion metric tons. It appears that the U.S. has sufficient reserves and resources for alunite to be considered as a potential non-bauxite source of alumina.

Jan 1, 1980

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

While there have always been mining activities on the outcrops of the copper deposits around Tsumeb, large scale mining activities in Namibia only started in colonial times. Originally focusing on the known deposits, the then German Geological Survey and independent geologists soon discovered significant deposits all over the country. This eventually lead to intensive mining operations all over the country on copper, gold, diamonds, fluorspar and finally uranium. Ever since those days, mining has been one of the major economical factors of Namibia?s development, as shown in picture 1. In the Central Namib Desert mining on base metals started in 1901, and first uranium deposits were discovered as soon as 1910, later followed by others, this did, however, not lead to any mining activities on those uranium deposits in the following decades. [ ] The upswing in the use of nuclear energy in the 1960s and early 1970s triggered some extensive uranium exploration worldwide and also in Namibia. Several airborne radiometric overviews were conducted by the Geological Survey at this stage and eventually the first uranium mine was commissioned in 1976. In the following three decades, the focus of prospecting activities in Namibia shifted away from uranium again. However, since 2000 the forecast for a developing and growing global economy and its even stronger growing energy demand have triggered a large number of nuclear energy projects worldwide, thus increasing the installed nuclear energy generation capacity from 387 GW today to more than 490 GW in 2025.

Jan 1, 2011

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By J. S. Rapp

This report is based on existing reports and recently gathered field data. It discusses mineral resource potential of Tertiary playas in the Fort Irwin region. An estimated 1.3 million tons of measured salt "reserves", and 20 million tons of indicated salt resources, have been identified north of the fort. Other indicated resources include 300,000 tons of celestite, 800,000 tons of gypsum, and 10 million tons of selenite. Zeolitic tuff was mined south of Fort Irwin from 1978 to 1984, and unexplored occurrences are widespread. Calcium-bentonite is mined near Barstow, and more may exist, including valuable sodium-and lithium-based bentonites.

Jan 1, 1992

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By W. E. Heinrichs, R. W. Davis

Introduction Cross borehole seismic tomography (CBST) is a geophysical technique that allows definition of the distribution of some physical rock property between two boreholes. The method is similar to the computer-assisted tomography (CAT) scans used by the medical industry. This paper describes the method, its applications and the developing trends in its use that interest the mining industry. The idea of using tomography in connection with geophysical methods for measuring rock properties between boreholes has been around for three or four decades. Until the advent of high-speed, large-capacity computers, the necessary calculations were too formidable for production use. Another factor in the development of the technique has been the refinement of a mathematical base to meet the needs of the medical industry. The geophysical applications have benefited from this refinement. An extensive discussion of the basic theory is given in Kak and Slaney (1988). CBST, although widely researched and written about, is still not extensively put to use in mining and engineering projects. Most real world examples in the literature have come from research carried out by government laboratories or by large companies. An exception is the regular use by Prospection Geophysique Francaise (Cottin et al., 1986) in damsite investigations. The Japanese appear to be doing extensive research and testing of CBST's uses in civil engineering projects (Saito et al., 1988). Canada is researching the use of the method in connection with nuclear waste site investigations (Wong et al., 1987). Finland has tested the method in connection with a foundation investigation for a nuclear power plant (Cosma et al., 1984). In the US, the US Bureau of Mines has taken an interest in using CBST as a means to enhance in situ mining operations (Tweeton, 1988). Major oil companies are examining the method as a tool in oil field development (Justice et al., 1989). Description of the method CBST involves placing a series of receivers down one borehole and recording transmissions from an energy source placed successively at a series of positions in another hole. The objective is to generate a dense network of seismic raypaths between the holes. The denser the network of raypaths, the better the features between the boreholes are resolved. Either seismic travel times or sine wave amplitudes are measured by the receivers. Analysis of travel times between boreholes develops a picture of rock velocities between the holes. Analysis of seismic wave amplitudes develops a picture of the distribution of energy transmission characteristics between the holes. These seismic properties can be used to define occurrences of fracture zones, lenticular sequences or other important geologic data not apparent from examination of the borehole logs. When longitudinal (compressional) and transverse (shear) waves are analyzed, the physical properties, such as elastic moduli, can also be mapped. When wave amplitudes are measured, rather extensive corrections to the data are necessary. There is some disagreement among researchers as to the feasibility of making some of the corrections. For this reason, this paper will concentrate primarily on travel time analysis. Wave amplitude analysis will be mentioned occasionally only in passing. This does not mean that amplitude analysis does not provide important data on rock parameters, only that for the present there are limitations on its uses. Vertical seismic profiling (VSP), extensively used in recent years in oil exploration, is similar to CBST. Instead of using two boreholes, however, the VSP method uses an array of seismic sources or detectors down one hole and an array of detectors or sources along the surface radiating outward from the hole. While adequate for determining vertical velocity distributions, the VSP method is not, by itself, suitable for most engineering or mining projects. Computer programs used to analyze the field data make use of the fact that the total travel time or change in signal amplitude between boreholes is described by Dines and Lytle (1979) as: [9k = f Rk f( x,Y) ds (1)] where gk = the total time or attenuation along the kth ray path,

Jan 1, 1992

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By Donald E. Ranta

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 assays and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1983